• Journal of Electrical Engineering and Technology
• /
• v.9 no.1
• /
• pp.80-89
• /
• 2014

A stochastic optimal power flow (S-OPF) model considering uncertainties of load and wind power is developed based on chance constrained programming (CCP). The difficulties in solving the model are the nonlinearity and probabilistic constraints. In this paper, a limit relaxation approach and an iterative learning control (ILC) method are implemented to solve the S-OPF model indirectly. The limit relaxation approach narrows the solution space by introducing regulatory factors, according to the relationship between the constraint equations and the optimization variables. The regulatory factors are designed by ILC method to ensure the optimality of final solution under a predefined confidence level. The optimization algorithm for S-OPF is completed based on the combination of limit relaxation and ILC and tested on the IEEE 14-bus system.

• Proceedings of the KIPE Conference
• /
• 2005.07a
• /
• pp.251-253
• /
• 2005

This paper presents a study on a current control of a PM synchronous motor which is fed by two-level voltage source inverter in the high modulation index area. In order to increase dynamic response and extend speed limit caused by voltage limit, overmodulation method is generally used. The current control in overmodulation have voltage limit. So larger voltage command than voltage limit should be diminished. In this paper, the problem conventional normalization method is analyzed and New normalization method in overmodulation region is proposed.

• Journal of Korean Society for Quality Management
• /
• v.26 no.1
• /
• pp.61-73
• /
• 1998

The quality control literature contains a substantial number of articles concerned with how to optimally choose control limits in order to minimize production cost. The purpose of the this study is to determine the economic setting for the process mean of an industrial process. In this study it is assumed that the lower control limit is set by government regulations and the u, pp.r limit and process mean are chosen based on economic considerations. Much research has been conducted on this problem under the condition of the fixed rpm(rate per minute). However a variance can be increased in proportion to the level of rpm and the increase of the variance can change the optimal process mean. Therefore, it is desirable to determine both the process mean and the level of rpm simultaneously. In this paper, a mathematical model is presented which considers the u, pp.r limit and the rpm as variables.

• Proceedings of the KIEE Conference
• /
• 2000.11d
• /
• pp.629-632
• /
• 2000

Nonlinear frictions which generate many problems in control system exist in almost all the servor control systems. In this paper, the design procedure which employs $H_\infty$ integral controller including two integrators with performance weight is proposed to improve performance of the control system. Limit cycles are unavoidable by the effect of interaction between two integrators and coulomb friction in these system. The describing function method is used to check the limit cycles and determine the coefficients of performance weights to minimize the effect of the limit cycles.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.28 no.4
• /
• pp.85-93
• /
• 2005

This paper is designed a VSI ${\overline{X}}$-CRL synthetic control chart in aspect of economy. We found the optimal sampling interval and various control limit factors under various cost parameters using cost function, proposed Lorenzen and Vance. Optimal design parameters include the sample size, control limit width, sampling interval, CRL/S chart control limit; L. Comparison and analysis of cost parameters are applied between synthetic VSI ${\overline{X}}$-CRL chart and FSI ${\overline{X}}$-CRL chart. The result of this paper shows that VSI ${\overline{X}}$-CRL chart brings cost-cutting effect of 3.04% control expense less than FSI control chart. It may not be difficult to establish the optimal economic control parameters to apply the practical cost parameters in the field.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.1
• /
• pp.61-65
• /
• 2012

Some works about the current sensorless control of a synchronous reluctance motor have been presented. However, there is no analysis about the performance and the detuning effect of the current sensorless control. This paper presents the problems and the detuning effect of the current sensorless control of a synchronous reluctance motor by simulation results. In addition, torque limiter is proposed to limit the torque current within the torque limit.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.1A
• /
• pp.35-41
• /
• 2011

In concrete structural design provisons, two methods are normally provided to control deflection; direct method and indirect method. It is more efficient to use the indirect deflection control by which the span/depth ratio is limited not to exceed an allowable deflection limit. Because actual deflections are affected by many causes, it is complicated to evaluate actual deflections. In this study, limit span/depth ratios are derived from the deflection calculated directly at the serviceability limit state in RC members. The deflection is obtained from using average curvature, which depends on materials model used. The main variables examined are tension stiffening effect, concrete strength, cross section size and compressive steel ratio. It could be appeared that more analytical consistency is secured to use the 2nd order form of tension stiffening effect. And the limit span/depth ratio is dependent on material strength, tensile and compressive steel ratio but it is independent on cross-section size.

• Journal of The Korean Society of Integrative Medicine
• /
• v.10 no.2
• /
• pp.203-210
• /
• 2022

Purpose : The purpose of this study was to investigate the effect of vestibular sensory stimulation exercise on the limit of stability, dynamic weight shift, and upper and lower extremities reaction time in adult women. Methods : This study was conducted with 30 female. All subjects were randomly and equally assigned to an experimental group and a control group of 15 each. Subjects assigned to the experimental group received vestibular sensory stimulation training for 6 weeks. For the intervention, vestibular sensory stimulation exercises were conducted by referring to the Hamid exercise method and the Cawthorne-Cooksey exercise method, and the control group did not receive any intervention. All subjects were tested for limit of stability, dynamic weight shift, and upper and lower extremities reaction time before and after the intervention. Results : The results of this study showed significant differences between groups in reaction time, moving velocity, and directional control in the limit of stability test after intervention. In the dynamic weight shift test after intervention, there was a significant difference between the groups in the slow directional control of left and right. And in the upper and lower extremities reaction time test after intervention, both scores and reaction time showed significant differences between groups. Conclusion : As a result, the three vestibular sensory stimulation exercises applied in this study improved the limit of stability, dynamic weight shift, and upper and lower extremities reaction time.

• Journal of Korean Society for Quality Management
• /
• v.26 no.3
• /
• pp.60-70
• /
• 1998

When driving the expected loss generated by the quality deviation, Taguchi(1991b) assumed that an objective characteristic has the uniform distribution in its control limit. But it is reasonable to assume that an objective characteristic has the normal distribution than the uniform distribution. Since the triangular distribution is similar to the normal distribution and easy to handle as well, in this article, we first find the optimum measurement interval and the optimum control limit under the triangular distribution. Under the normal assumption, the modified method is compared to Taguchi's. Secondly we find the numerical value solution of the optimum measurement interval and the optimum control limit under the normal distribution.

• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.57-59
• /
• 2018

This paper presents a novel reference variable speed control scheme of a BLDC motor for the high-speed blender machine according to the current limit. Because of a pulsating load variation of a high-speed blender machine, the actual speed is pulsated by the current limit in the high-speed region. The proposed control scheme uses a variable reference speed to reduce the speed variation from the current limit in the constant power region. The pulsated load is occurred at the material crushing, then the pulsated load is reduced after grinding. The reference speed is smoothly reduced at the pulsated load variation, then the enough torque can make a constant speed during crushing. When the pulsating load is reduced, the reference speed is automatically increased to the original speed value. The proposed control scheme is verified by experimental result by practical blender machine.