• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.05
• /
• pp.156-160
• /
• 1997

In this paper, the control scheme is proposed that PI controller parameter used for TAH speed control is adapted by fuzzy logic method using only the motor current waveform. By scheduling PI parameters, minimization of the vibration and the energy consumption and overcoming AoP loads becomes possible. In in vitro tests experimental results show our approach is a good scheme that is adapted to changing afterloads well.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.48 no.10
• /
• pp.1327-1334
• /
• 1999

The stabilization control of ball-beam system is difficult because of its nonlinearity and structural unstability. Futhermore, a series of classical methods such as the PID and the full state feedback controller(FSFC) based on the local linearizations have narrow stabilizable regions. At the same time, the fine tunings of their gain parameters are also troublesome. Therefore, in this paper, three improved design techniques of stabilization controller for a ball-beam system were proposed. These parameter tuning methods in the double PID controller(DPIDC), the FSFC and the a sliding mode controller(SMC) were dependent upon the Real Value Elitist Genetic Algorithm (RVEGA). Finally, by applying the DPIDC, the FSFC and the Real Variable Elitist Genetic Algorithm based Sliding Mode Control(RVEGA SMC) to the stabilizations of a ball-beam system, the performances of the RVEGA SMC technique were showed to be superior to those of two other type controllers.

• Proceedings of the KIPE Conference
• /
• 2002.07a
• /
• pp.166-169
• /
• 2002

The purpose of this paper is to develop systematic analysis and automatic tuning rule of PID controller for industry servo applications. Considering the coupling of inner current control loop and speed loop delay, the target plant fit into second-order plus time delay model. Based on PID controller design for high-order plus known/unknown time delay plant model, some formulars are provided for the control gain calculation and system-based theoretical analysis is developed, and it also allows an automatic controller setup to benefit the inexperienced user. In addition, the proposed design rule gives uniformly satisfactory performance and the motor speed stays on a desired response curve with minimal oscillation and settling time. This approach can be applicable in conjunction with the cascaded control loop which is widely used in practice.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.50 no.9
• /
• pp.423-429
• /
• 2001

This paper proposes adaptive impedance control algorithm using fuzzy inference when robot contacts with its environments. The characteristics of the adaptive impedance controller is to adapt with parametric uncertainty and nonlinear conditions. The control algorithm is to join impedance controller with fuzzy inference engine. The proposed control method overcomes the problem of impedance controller using gain-tuning algorithm of fuzzy inference engine. We implemented an experimental set-up consisting of environment-generated one-link robot system and DSP system for controller development. We apply the adaptive fuzzy impedance controller to one-link root system, and it shows the good performance on regulating the interactive force in case of contacting with arbitrary environment.

• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.138-141
• /
• 2001

This paper presents a study on successive approximation measurement of mechanical parameters for motor control system. At the first step of servo system installation, control system gain tuning is troublesome work. Recently, autotuning method of motion controller for motor drive system is based on parameter measurement and identification. On the case of first order mechanical system (mechanical parameters are modified by simple inertia and friction), it is necessary for good response to get the accurate measurement or identification of the mechanical parameters . In this paper, novel method applies the binary successive approximation measurement to the inertia and friction coefficient. Computer simulation and experiment for the proposed method will show verification of accuracy and usefulness.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.6
• /
• pp.957-966
• /
• 2023

In this paper, we propose a new real-time adaptive PID temperature control technique. This is a technique that prevents overshoot by introducing a model that represents the control object. To prevent excessive integration that causes overshoot, integral control adjusts the integral gain to track the heat loss of the model in real time. In the conventional PID control, the integration was dependent on proportional control and the gain was fixed to a constant. As a result, applying two gains that mismatch each other could cause excessive overshoot. However, the proposed adaptive control actively eliminates overshoot so that the integral control amount does not always exceed the heat loss. The cause of overshoot in PID control is integration. Basically, proportional control does not cause overshoot. Therefore, according to the proposed technique, adaptive PID control without the need for tuning experiments can be realized.

• Proceedings of the KIEE Conference
• /
• 2008.10b
• /
• pp.217-218
• /
• 2008

Since the digital TV signal band is very wide ($54{\sim}806MHz$), the VCO used in the frequency synthesizer must also have a wide frequency tuning range. Multiple LC VCOs have been used to cover such wide frequency band. However, the chip area increases due to the increased number of integrated inductors. A general method for achieving both reduced VCO gain(Kvco) and wide frequency band is to use the switched-capacitor bank LC VCO. In this paper, a scheme is proposed to cover the full band using only one VCO. The RF VCO block designed using a 0.18um CMOS process consists of a wideband LC VCO with reduced variation of VCO gain and frequency steps. Buffers, divide-by-2 circuits and control logics the simulation results show that the designed circuit has a phase noise at 100kHz better than -106dBc/Hz throughout the signal band and consumes $9.5{\sim}13mA$ from a 1.8V supply.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.16 no.5
• /
• pp.223-229
• /
• 2023

This Paper propose the method that measure main system parameters for PI(proportional-integral) current control of a.c. motor adopting the vector control technique. For current control, the PI control input is could be tuning by several selective methods. Among the several methods, the method that using the main system parameters, wire resistance and inductance, are frequently used. In this study, the technique to dissect and measure these two system parameters through the results of simple feedback control. This analytic measurement method is measuring parameters step by step dissecting the results of P control using simple proportional feedback gain about the unit step or multiple step reference command. This strategy is an real time analytic measurement method that calculate current control gains of torque component and flux component both for vector control of A.C. motor without introducing the further measurement circuits and complex measuring algorithms.

• The Transactions of the Korean Institute of Electrical Engineers A
• /
• v.51 no.4
• /
• pp.188-195
• /
• 2002

We proposed the design of SVC adaptive fuzzy logic controller(AFLC) using Tabu search and neural network. We tuned the gains of input-output variables of fuzzy logic controller(FLC) and weights of neural network using Tabu search. Neural network was used for adaptively tuning the output gain of FLC. The weights of neural network was learned from the back propagation algorithm in real-time. To evaluate the usefulness of AFLC, we applied the proposed method to single-machine infinite system. AFLC showed the better control performance than PD controller and GAFLS[10] for three-phase fault in nominal load which had used when tuning AFLC. To show the robustness of AFLC, we applied the proposed method to disturbances such as three-phase fault in heavy and light load. AFLC showed the better robustness than PD controller and GAFLC[10].

• Journal of Energy Engineering
• /
• v.5 no.1
• /
• pp.28-33
• /
• 1996

This study was carried out find out the appropriate tuning method of PID controller for a package type gas engine cogeneration system in terms of stabilizing the engine coolant temperature and system heat balance. In order to acquire the proper parameters of the controller, a system transfer function was set as a first order plus dead time model and thereafter model parameters were determined by using several tuning methods. And, with determined values of parameters and the system transfer functions, optimal turning method was selected by simulating the process using MATLAB. From the experimental results, it was found that obtained PID gains made the system stable in various operating conditions.