• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.729-732
• /
• 2001

Digital signal processors(DSP) are widely used in modern power conversion devices, ac motor drives. However, generating pulse-width modulation(PWM) gating signals requires so high sampling rates that most computation resources of the DSP must be devoted to generating them. This paper presents an ASIC realization of 2 channel space-vector PWM(SVPWM). The developed DSP(ECLDSP) board can transmit gating signals to 2 converter/inverter and control them. ECLDSP board is used for control the various kinds of power-quality improvement systems.

• Journal of Institute of Control, Robotics and Systems
• /
• v.8 no.6
• /
• pp.514-523
• /
• 2002

Feeder arrangement is an important element of process planning for printed circuit board assembly systems. This paper newly proposes a feeder arrangement method for multihead-gantry chip mounters. The multihead-gantry chip mounters are very popular in printed circuit board assembly system, but the research has been mainly focused on single-head-gantry chip mounters. We present an integer programming formulation for optimization problem of multihead-gantry chip mounters, and propose a heuristic method to solve the large NP-complete problem in reasonable time. Dynamic programming method is then applied to feeder arrangement optimization to reduce the overall assembly time. Comparative simulation results are finally presented to verify the usefulness of the proposed method.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.12
• /
• pp.1194-1202
• /
• 2011

A touch panel system has been one of the most widely used input devices. In this study, a touch panel embedded system using accelerometers is considered in order to make commercial white-boards or plates into touch panels. Three accelerometers are located at different positions on such a white board, so that touch points on the board can be identified using the sensors. For the identification of touch points, a TDOA (Time Difference of Arrivals) technique is applied in the algorithm which was implemented in a DSP board (TI 6713 DSK), which can provide a precise touch location by using the cross-correlation function of measured signals from the three accelerometers. Experiment results show that the touch panel system with accelerometers could provide the exact touch location. Thus a novel approach using such accelerometers could be applied to a new touch panel system.

• Journal of Institute of Control, Robotics and Systems
• /
• v.13 no.6
• /
• pp.519-524
• /
• 2007

The OBC(on-board computer) of a satellite which plays a role of the controller for the satellite should be equipped with preventive measures against transient errors caused by SEU(single event upset). Since memory devices are pretty much susceptible to these transient errors, it is essential to protect memory devices against SFU. A common method exploits an error detection and correction code and additional memory devices, combined with periodic memory scrubbing. This paper proposes an effective memory scrubbing scheme for the OBC of STSAT-2. The memory system of the OBC is briefly mentioned and the reliability of the information stored in the memory system is analyzed. The result of the reliability analysis shows that there exist optimal scrubbing periods achieving the maximum reliability for allowed overall scrubbing overhead and they are dependent on the significance of the information stored. These optimal scrubbing periods from a reliability point of view are derived analytically.

• KIPS Transactions on Computer and Communication Systems
• /
• v.5 no.9
• /
• pp.285-292
• /
• 2016

By adding short-range wireless communication function such as Bluetooth and Wi-Fi to the last vehicle in conjunction with a smart phone, a modern automobile is becoming entertainment screen to determine a variety of information such as car location information, diagnosis information, etc. through the ECU vehicle electronic control unit. In this study, by utilizing short-range communications capability of the on-board diagnostic devices and smart phones in association with the on-board diagnostics, compatibility tests among a number of smart phone models, Bluetooth and NFC(Near Field Communication) were carried out and those results were analyzed. Furthermore, composition of on-board diagnostic device having Bluetooth and NFC interface function and the fault diagnosis function were implemented, and fault diagnosis debugging program was developed. In addition, fault diagnosis data of the vehicle via the OBD-II interface was extracted. Finally, the on-board diagnostics CAN Protocol implementation has been proposed, and the results of work was analyzed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.6
• /
• pp.1146-1151
• /
• 2011

There are two methods for train control in information transmission by using track circuit system and installing wayside transmitter. Information signal is transmitted to the on-board antenna by using rails. Continuous information about train intervals, speed and route is received by on-board antenna in AF track circuit system. The information signal is included with carrier wave and received by magnetic coupling in the on-board antenna. Therefore, it is important to define standard current level in the AF track circuit system. When current flowed to rails is low, magnetic sensors are not operated by decreasing magnetic field intensity. Hence, SNR is decreased because electric field intensity is decreased. When the SNR is decreased, there is the serious influence of noise upon demodulation. So, the frequency of information signal is not extracted in frequency response. Thus, it is possible to happen to train accident and delay as the information signal is not analyzed in the on-board antenna. In this paper, standard energy density is calculated by using Parseval's theory in UM71c track circuit. Hence, detection time of information signal is presented.

• Journal of Institute of Control, Robotics and Systems
• /
• v.5 no.6
• /
• pp.691-697
• /
• 1999

This paper describes the implementation of a high speed image processing board. This image processing board is consist of a image acquisition part and a image processing part. The image acquistion part is digitizing the image input data from CIS and save it to the dual port RAM. By putting on the dual port memory between two parts, during acquistion of image, the image processing part can be effectively processing of large-volume image data. Most of all image preprocessing part are integrated in a large-scaled FPGA. We arwe using ADSP-2181 of the Analog Device Inc., LTD. for a image processing part, and using the available all memory of DSP for the large-volume image data. Especially, using of IDMA exchanges the data with the external microprocessor or the external PC, and can watch the result of image processing and acquired image. Finally, we show that an implemented image processing board used for the simulation of image retreval by the one of the typical application.

• Korean Journal of Materials Research
• /
• v.28 no.1
• /
• pp.62-67
• /
• 2018

Active clay, bentonite and zeolite were used as porous materials for humidity controlling ceramic boards. The specific area and the pore volume of active clay were higher than bentonite and zeolite. The flexible strength of the gypsum board decreased with an increasing amount of porous material, and the flexible strength was lowest when active clay with a higher specific surface area than others porous materials was added. The specific surface area and total pore volume of ceramic boards containing porous material were highest at $102.25m^2/g$, $0.142cm^3/g$, respectively, when the active clay was added. In addition, as the amount of added porous materials increased, the specific surface area and total pore volume of the ceramic board increased, but the average pore diameter decreased. The addition of s porous materials with a high specific area and a large pore volume improved the moisture absorptive and desorptive performance of the ceramic board. Therefore, in this experiment, the moisture absorptive and desorptive properties were the best when active clay was added. Furthermore, as the amount of added porous materials increased, the moisture absorptive and desorptive properties improved. When 70 mass% of active clay was added to ${\alpha}$-type gypsum, the hygroscopicity was the highest, about $300g/m^2$, in this experiment.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.575-580
• /
• 2003

In this paper, we develop a control hardware such as an FPGA based general purpose controller with a DSP board to solve nonlinear control problems. PID control algorithms are implemented in an FPGA and neural network control algorithms are implemented in a DSP board. PID controllers implemented on an FPGA was designed by using VHDL to achieve high performance and flexibility. By using high capacity of an FPGA, the additional hardware such as an encoder counter and a PWM generator, can be implemented in a single FPGA device. As a result, the noise and power dissipation problems can be minimized and the cost effectiveness can be achieved. In order to show the performance of the developed controller, it was tested for controlling nonlinear systems such as an inverted pendulum.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.951-956
• /
• 2007

This paper suggests a high-speed control method which is suitable for multi-joint robots using a real-time stand-alone controller for general-purpose. The fast processing controller consists of a PCI Interface Board and 2-axe PWM drivers. The PCI Interface Board consists of 32-channel PWM output ports, 32-channel Encoder Counters, 32-channel A/D Converters and 48-channel Digital I/O ports, and all the I/O data transmissions are completed within 1ms. And The 2-axe PWM driver can be redesigned easily in order to embed in each link. Experimental implementations show that the high-speed control method can be used for the real-time control which is essential to controlling of multi-body robots such as humanoid robots. Especially, it is efficient for realizing the model-based motion control in demand of much calculation time by the high I/O communication speed.