• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.8
• /
• pp.843-848
• /
• 2015

The objective of this study is to observe and optimize a typical ocean environment and reduce wave reflections in the wave flume. In order to generate ocean waves in the wave flume, a combination of a horizontal piston type wave generator and wave absorbers was installed in the channel. Two probes for measuring the wave heights, i.e., wave level gauges, were used to record the continuous variation of the wave surface, the phase difference, and the maximum (crest) and minimum (trough) points of the propagating waves. In order to optimize the shape and size of the propagating waves, several absorption methods were proposed. Apart from an active wave absorption method, we used methods that involved vertical porous plates, horizontal punching plates, and sloping-wall-type wave absorbers. To obtain the best propagating waves, a sloping-wall-type wave absorber was chosen and tested in terms of the constitutive filling materials and the location and shape of the plate. This study also focused on the theoretical prediction of the wave surface, separating them into the incident and reflective components. From the results, it is evident that the wave absorber comprising a hard filling material exhibits a better performance than the absorber comprising a soft material, i.e., the wave absorber can be a strong sink to control the energy of the incoming wave. In addition, larger wave absorbers correspond to lower reflectance because a larger volume can reduce the incoming wave energy. Therefore, at constant absorber conditions, the reflectance of the wave increases as the wave period increases. Finally, the reflectance of the wave was controlled to be less than 0.1 in this study so that the wave flume can be used to simulate an offshore environment.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.225-228
• /
• 2008

This paper presents out-of-plane shear strength models for composite wall with steel plates based on limit theorem in the framework of the plasticity theory. The formulas proposed by JEAG 4618 need to be reconsidered with a couple of limitations; ignoring the effect of bond stress generated by studs in the process of calculating arch action, illogically discriminating between concrete shear cracking strength and arch strength by algebraic relation in short shear span ratio(0-2.0). In most cases, reinforcement ratio is not sufficient to yield, as a result, arch strength is determined by accounting equilibrium including both bond strength and concrete compressive strength. We conducted experimental research assuming that SC wall is a continuous beam under the simplified loading patterns, changing main valuables involving the number of studs, stirrups. The results show good agreements with the formula and we quoted the test results of JEAG.

• Korean Institute of Interior Design Journal
• /
• v.26 no.6
• /
• pp.97-105
• /
• 2017

Korea is promoted STEAM education since 2011. Furthermore, in high school education, based on the in-depth elective course's teaching and learning contents of science. The STEAM program can improve students' competence because it encourages to self-directed learning through the vocational project performance. Therefore, in this study, we researched a design education program for the experience of fusion and complex design based on STEAM education concept. We developed an education program to design insulation wall systems using up-cycling concepts to increase energy efficiency. As a result, the characteristics of the fusion education and the theoretical study about the learner-centered education curriculum, the analysis of the high school curriculum, the STEAM elements, The program was revised and supplemented through consultation with STEAM experts. In addition, the developed program was applied to high school students, and each step were analyzed based on the educational method theory. The following results were obtained. First, this study presented a program to cope with the needs of high school intensive education. Second, it provided learning motivation by combining flipped-learning as a way to train STEAM education contents. Third, it is required to develop differentiated and continuous program development and data sharing Fourth, in order to operate and promote the future environment design STEAM school, it is necessary to expand educational programs for high school students in the region through linkage with various universities.

• Restorative Dentistry and Endodontics
• /
• v.42 no.2
• /
• pp.111-117
• /
• 2017

Objectives: Periapical lesions, including periapical cyst (PC), periapical granuloma (PG), and periapical abscess (PA), are frequently affected by chemical/physical damage during root canal treatment or severe bacterial infection, and thus, the differential diagnosis of periapical lesions may be difficult due to the presence of severe inflammatory reaction. The aim of this study was to make differential diagnosis among PC, PG, and PA under polarizing microscope. Materials and Methods: The collagen birefringence patterns of 319 cases of PC (n = 122), PG (n = 158), and PA (n = 39) obtained using a polarizing microscope were compared. In addition, 6 cases of periodontal fibroma (PF) were used as positive controls. Results: Collagen birefringence was condensed with a thick, linear band-like pattern in PC, but was short and irregularly scattered in PG, and scarce or absent in PA. PF showed intense collagen birefringence with a short, palisading pattern but no continuous band-like pattern. The linear band-like birefringence in PC was ascribed to pre-existing expansile tensile stress of the cyst wall. Conclusions: In this study all PCs (n = 122) were distinguishable from PGs and PAs by their characteristic birefringence, despite the absence of lining epithelium (n = 20). Therefore, the authors suggest that the presence of linear band-like collagen birefringence of the cyst wall aids the diagnostic differentiation of PC from PG and PA.

• Journal of the Korean Society of Visualization
• /
• v.18 no.3
• /
• pp.23-34
• /
• 2020

Two-phase flow and heat transfer characteristics during the reflood phase of a single heated rod in the KHU reflood experimental facility were examined. Two-phase flow behavior during the reflooding experiment was carefully visualized along with transient temperature measurement at a point inside the heated rod. By numerically solving one-dimensional inverse heat conduction equation using the measured temperature data, time-resolved wall heat flux and temperature histories at the interface of the heated rod and coolant were obtained. Once water coolant was injected into the test section from the bottom to reflood the heated rod of >700℃, vast vapor bubbles and droplets were generated near the reflood front and dispersed flow film boiling consisted of continuous vapor flow and tiny liquid droplets appeared in the upper part. Following the dispersed flow film boiling, inverted annular/slug/churn flow film boiling regimes were sequentially observed and the wall temperature gradually decreased. When so-called minimum film boiling temperature reached, the stable vapor film between the heated rod and coolant was suddenly collapsed, resulting in the quenching transition from film boiling into nucleate boiling. The moving speed of the quench front measured in the present study showed a good agreement with prediction by a correlation in literature. The obtained results revealed that typical two-phase flow and heat transfer behaviors during the reflood phase of overheated fuel rods in light water nuclear reactors are well reproduced in the KHU facility. Thus, the verified reflood experimental facility can be used to explore the effects of other affecting parameters, such as CRUD, on the reflood heat transfer behaviors in practical nuclear reactors.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.35 no.6
• /
• pp.431-436
• /
• 2009

There are five principal causes for excessive bleeding in the immediate postextraction phase ; (1) Vascular wall alteration (wound infection, scurvy, chemicals, allergy) (2) Disorders of platelet function (genetic defect, drug-aspirin, autoimmune disease) (3) Thrombocytopenic purpuras (radiation, leukemia), (4) Inherited disorders of coagulation (hemophilia, Christmas disease, vitamin deficiency, anticoagulation drug-heparin, coumarin). If the hemorrhage from postextraction wound is unusually aggressive, and then dehydration and airway problem are occurred, the socket must be packed with gelatine sponge(Gelfoam) that was moistened with thrombin and wound closure & pressure dressing are applied. The thrombin clots fibrinogen to produce rapid hemostasis. Gelatine sponges moistened with thrombin provide effective coagulation of hemorrhage from small veins and capillaries. But, in dental alveoli, gelatine sponges may absorb oral microorganisms and cause alveolar osteitis (infection). This is a case report of bleeding control by continuous rubber strip & iodoform gauze drainage (without gelfoam packing) of active bleeding infection sites of three teeth extraction wounds in a 46-years-old female patient with advanced liver cirrhosis.

• Microbiology and Biotechnology Letters
• /
• v.26 no.4
• /
• pp.352-357
• /
• 1998

Biodegradation of benzoate and m-toluate was investigated using a Pseudomonas sp. isolated in a continuous culture for 45 days with a step-wise increase of the subsrates. The optimum mixture ratio of benzoate and m-toluate was 75% and 25%, respectively. During 45-day culture, removal of benzoate and m-toluate, which was replaced 2,000 ppm on the 30th day were 94% and 79%, respectively, when COD removal rate was 80%. The enzymatic activity of catechol 1,2-dioxygenase increased and that of catechol 2,3-dioxygenase decreased as the concentration of m-toluate was increased. These results suggested that m-toluate induced enzyme activity for degradation of benzoate. The shape of isolated strain in the continuous culture was investigated with SEM and the results showed that the cell shape was more damage according to the higher concentration of aromatic hydrocarbons. Therefore, we suggested that the tolerance against aromatic hydrocarbons was related to not only enzymatic activity but also characteristic of cell membrane or cell wall.

• Journal of Korean Society for Geospatial Information Science
• /
• v.15 no.4
• /
• pp.11-20
• /
• 2007

Most natural disasters in Korea are caused by meteorological natural phenomena, which include storms, heavy rains, heavy snow, hail, tidal waves, and earthquakes. Rainfall is the most frequent cause of disasters and accounts for about 80% of all disasters. Particularly in recent years, Korea has seen annual occurrences of natural disasters associated with landslides (slope and retaining wall collapse and burying) due to meteorological causes from the increasing intensity of heavy rains including local heavy rainfalls. In Korea, it is critical to analyze the characteristics of landslides according to rainfall characteristics and to take necessary and proper measures for them. This study assessed the possibility of landslides in the Gangwon region with a geographic information system by taking into account the inducer factors of landslides and the maximum continuous rainfall of each area. It also analyzed areas susceptible to landslides and checked the distribution of landslide-prone areas by considering the rainfall characteristics of those areas.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.5
• /
• pp.744-752
• /
• 2000

The influence of arrangement and length of discrete ribs on heat/mass transfer and friction loss is investigated. Mass transfer experiments are conducted to obtain the detailed local heat/mass transfer information on the ribbed wall. The aspect ratio (width/height) of the duct is 2.04 and the rib height is one tenth of the duct height, such that the ratio of the rib height to hydraulic diameter is 0.0743. The ratio of rib-to-rib distance to rib height is 10. The discrete ribs were made by dividing each continuous rib into 2, 3 or 5 pieces and attached periodically to the top and the bottom walls of the duct with a parallel orientation The combined effects of rib angle and length of the discrete ribs on heat/mass transfer ae considered for the rib angles $({\alpha})\;of\;90^{\circ}\;and\;45^{\circ}$. As the number of the discrete ribs increases, the uniformity of the heat/mass transfer distributions increases. For $(\alpha})=90^{\circ}$, the heat/mass transfer enhancement with the discrete ribs is remarkable, while the heat/mass transfer performances are slightly higher than that of the transverse continuous ribs due to the accompanied high friction loss penalty. For $(\alpha})=90^{\circ}$, the average heat/mass transfer coefficients and the heat/mass transfer performances decrease slightly with the discrete ribs compared to the case of the angled continuous ribs.

• Journal of the Korean Geosynthetics Society
• /
• v.22 no.2
• /
• pp.85-92
• /
• 2023

This paper describes the comparative results of measured and predicted values for the horizontal displacement of earth retaining wall based on two field cases, in order to evaluate the application of lateral earth pressure to earth retaining wall supported by earth anchor in Jeju. The prediction of lateral earth pressure acting on the earth retaining wall was performed by elasto-plastic analysis using Rankine earth pressure, Hong & Yun lateral earth pressure, Terzaghi & Peck modified lateral earth pressure, and Tschebotarioff lateral earth pressure. As a result, the predicted value of the maximum horizontal displacement for site A was about 10 to 12 times greater than the measured value, and in the case of site B, the predicted value was evaluated as about 9 to 12 times greater than the measured value. That is, both sites showed a similar increase rate in the maximum horizontal displacement by the predicted value compared to the measured value. In all field construction cases, the maximum horizontal displacement by measured values occurred in the sedimentary layer, soft rock layer, and clinker layer, and the horizontal displacement distribution was shown in a trapezoidal shape. The maximum horizontal displacement by the predicted value occurred around the clinker layer, and the horizontal displacement distribution was elliptical. In the ground with a clinker layer, the measured value showed a very different horizontal displacement tendency from the predicted value, because the clinker layer exists in the form of a rock layer and continuous layer. In other words, it is unreasonable to apply the existing prediction method, which is overestimated, because the characteristics of the earth pressure distribution in Jeju show a tendency to be quite different from the predicted earth pressure distribution. Therefore, it is necessary to conduct a research on the lateral earth pressure in the realistic Jeju that can secure more economic efficiency.