• Journal of Advanced Engineering and Technology
• /
• v.11 no.4
• /
• pp.245-251
• /
• 2018

Terahertz waves (T-ray) was extensively studied for the NDE (nondestructive evaluation) of characterization of trailing edges for a use of turbines composed with composite materials. The used NDE system were consisted of both CW(Continuous wave) and TDS (Time domain spectroscopy). The FRP composites were utilized for two kinds of both trailing edges of wind energy (non-conducting polymeric composites) and carbon fiber composites with conducting properties. The signals of T-ray in the TDS (Time domain spectroscopy) mode resembles almost that of ultrasound waves; however, a terahertz pulse could not penetrate a material with conductivity unlike ultrasound. Also, a method was suggested to obtain the "n" in the materials, which is called the refractive index (n). The data of refractive index (n) could be solved for the trailing edges. The trailing edges were scanned for characterization and inspection. C-scan and B-scan images were obtained and best optimal NDE techniques were suggested for complicated geometry samples by terahertz radiation. Especially, it is found that the defect image of T-ray corresponded with defect locations for the trailing edges of wind mill.

• Steel and Composite Structures
• /
• v.42 no.2
• /
• pp.151-159
• /
• 2022

This study discusses a hypothetical method for tracking the propagation damage of Carbon Reinforced Fiber Plastic (CRFP) components underneath vibration fatigue. The High Cycle Fatigue (HCF) behavior of composite materials was generally not as severe as this of admixture alloys. Each fissure initiation in metal alloys may quickly lead to the opposite. The HCF behavior of composite materials is usually an extended state of continuous degradation between resin and fibers. The increase is that any layer-to-layer contact conditions during delamination opening will cause a dynamic complex response, which may be non-linear and dependent on temperature. Usually resulted from major deformations, it could be properly surveyed by a non-contact investigation system. Here, this article discusses the scanning laser application of that vibrometer to track the propagation damage of CRFP components underneath fatigue vibration loading. Thus, the study purpose is to demonstrate that the investigation method can implement systematically a series of hypothetical means and dynamic characteristics. The application of the relaxation method based on numerical simulation in the Artificial Intelligence (AI) Evolved Bat (EB) strategy to reduce the dynamic response is proved by numerical simulation. Thermal imaging cameras are also measurement parts of the chain and provide information in qualitative about the temperature location of the evolution and hot spots of damage.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.29 no.1
• /
• pp.125-131
• /
• 2002

When a tooth is fracture with the pulp exposure, and if a fragment is large enough to save, reattachment of the fragment would be a choice of treatment and reattachment of the fragment provides several advantages over other forms of dental restoration following crown fracture. For the purpose of tooth reattachment, it is important to preserve the sound enamel around fracture area. For young patients, tooth reattachment has more advantages in the sense that they recover faster and that it enables other treatments at the same time. Through the continuous advancement in adhesion technology and the effort for aestheticism, various reattachment methods have been practiced and more efforts are considered necessary. The presented cases are that we had practiced in our department in Kyung Hee Medical center, I may address that fragmentation has been successfully done with aesthetically fine results, and no pathologic changes were found in short term follow-ups.

• Steel and Composite Structures
• /
• v.23 no.6
• /
• pp.727-736
• /
• 2017

The application of carbon fiber reinforced polymer (CFRP) in steel structures primarily includes two categories, i.e., the bond-critical application and the contact-critical application. Debonding failure and buckling failure are the main failure modes for these two applications. Conventional electrometric techniques may not provide precise results because of the limitations associated with single-point contact measurements. A nondestructive full-field measurement technique is a valuable alternative to conventional methods. In this study, the digital image correlation (DIC) technique was adopted to investigate the bond behavior and buckling behavior of CFRP-steel composite members. The CFRP-to-steel bonded joint and the CFRP-strengthened square hollow section (SHS) steel column were tested to verify the suitability of the DIC technique. The stereo-DIC technique was utilized to measure continuous deformation. The bond-slip relationship of the CFRP-to-steel interface was derived using the DIC data. Additionally, a multi-camera DIC system consisting of four stereo-DIC subsystems was proposed and applied to the compressive test of CFRP-strengthened SHS steel column. The precise buckling location and CFRP delamination of the CFRP-strengthened SHS steel column were identified. The experimental results confirm that the stereo-DIC technique can provide effective measurements for investigating the behaviors of CFRP-steel composite members.

• Journal of Korean Society of Environmental Engineers
• /
• v.28 no.10
• /
• pp.1055-1064
• /
• 2006

Extremely slow growing anammox(anaerobic ammonium oxidation) bacteria were cultivated using a combination of UASB(Upflow Anaerobic Sludge Blanket) reactor seeded with anaerobic granular sludge and carbon-fiber cultivating reactor. After 180 days of continuous cultivation, average nitrogen removal rate showed 0.54 kg $N/m^3-day$ when 0.6 kg $N/m^3-day$ of nitrogen loading was applied. The black granule was changed to brown and red granule as continuous operation, and the red granule was highly dependant on the high anammox activity. Microbial community structure of red granule in the UASB reactor was analyzed by molecular methods such as gene cloning, phylogenetic tree analysis, and FISH(Fluorescence In Situ Hybridization) method. As a result of gene cloning and phylogenetic tree analysis, 5 kinds of phylum were found to be Planctomycetes, Proteobacteria, Acidobacteria, Chlorobi and Chloroflexi. 13 clones were matched to anammox bacteria among 51 clones in the red anammox granule. In-silico test which used cloning information and FISH probe of the AMX368 was conducted to detect the presence of anammox bacteria in the red anammox granule. As a result of in-silico test only one clone was exactly matched to AMX368 but 11 clones was mutated one base among 18 bases representing all 12 clones are anammox bacteria. A filamentous Chloroflexi might be related to the granulation of anammox bacteria. As a result of FISH analysis, anammox bacteria was abundant in the red anammox granule.