• Journal of Biosystems Engineering
• /
• v.27 no.1
• /
• pp.45-50
• /
• 2002

This study was performed to develop thin layer drying equations fur short grain rough rice using far-infrared ray. Thin layer drying tests was conducted at four far-infrared ray temperature levels of 30, 40, 50, 60$^{\circ}C$ and two initial moisture content levels of 20.7, 26.2%(w.b.). The measured moisture ratios were fitted to Lewis and Page drying models by stepwise multiple regression analysis. Half response time of drying was affected by both drying temperature and initial moisture content at drying temperature of below 40$^{\circ}C$, but at above 40$^{\circ}C$ was mainly affected by drying temperature. Experimental constant(k) in Lewis model was a function of drying temperature, but K and N in Page model were function of drying temperature and initial moisture content. Moisture ratios predicted by two drying models agreed well with experimental values. But in the actual range of drying temperature above 30$^{\circ}C$ Page model was more suitable for predicting of drying rates.

• Korean Journal of Food Science and Technology
• /
• v.23 no.6
• /
• pp.702-710
• /
• 1991

The effects of washing and desinewing on the composition, fuctional properties, storage stability and texture of spent layer meat were investigated. Spent layer meat subjected to treatments involving water washing, bicarbonate washing and desinewing showed increases in moisture content and decreases in protein content, hydroxyproline content and heme pigment content. Increases in salt extractable protein content and water holding capacity and decreases in buffering capacity and emulsifying capacity were also observed. The 2-thiobarbituric acid values of washed and desinewed samples increased slowly during storage indicated the increase in storage stability compared to the control. Sample rolls prepared from bicarbonate washed and desinewed thigh and drumstick meats were scored by trained sensory panelists as less tough than the products made of ground thigh and drumstick meats.

• Journal of the Korean Society of Tobacco Science
• /
• v.8 no.1
• /
• pp.69-78
• /
• 1986

This experiment was carried out to Investigate the environmental changes of rhizosphere, behavior of nutrient components in soul, and nutrients uptake and growth response of the tobacco plant in the condition that mulch as polyethylene film, had been removed on the ridge at the 50th day after transplanting in comparison with continuous mulching condition. The results obtained were as follows; 1. After rainfall, soil moisture content In the plow layer was greatly increased without mulch in comparison with that of the plot with mulch. As a result, leaf water potential of tobacco plant without mulch was higher than that with mulch. 2. Available nutrients such as $NH_4-N, \;NO_3-N$, and total salts in the plow layer of the plot without mulch tended to be Increased, and especially accumulated on the surface layer owing to the redistribution of soil water by rainfall during the latter growth stage after removing mulch. 3. Nutrients uptake by tobacco was much more enhanced in the plot without mulch and resulted in higher contents of total nitrogen, $NO_3-N, \;P_2O_5, \;and K_5O$ in the tobacco leaf Especially higher content of nitrogen caused the delay of maturity resulting In the increased of dry weight of top part of tobacco in the plot without mulch toned to be Increased in comparison with that in mulching condition. Content of total nitrogen, $NO_3-N$, and nicotine in flue-lured leaves was much higher in the plot without. mulch than in mulching condition, but lower content of reducing sugar in the plot without mulch resulted in lower quality of tobacco.

• Journal of KIISE:Databases
• /
• v.30 no.3
• /
• pp.237-251
• /
• 2003

In this paper, we propose a video retrieval system to search logical structure and semantic contents of video data efficiently. The proposed system employs a layered modelling method that orBanifes video data in raw data layer, content layer and key frame layer. The layered modelling of the proposed system represents logical structures and semantic contents of video data in content layer. Also, the proposed system supports various types of searches such as text search, visual feature based similarity search, spatio-temporal relationship based similarity search and semantic contents search.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2002.08a
• /
• pp.632-634
• /
• 2002

Transparent dielectric layer having color-filter function in front panel for PDP(Plasma Display Panel) was successfully fabricated and characterized. Transparent dielectric layer in front panel was made of glass based on $PbO-SiO_2-B_2O_3$ ternary system. The change of properties with content variation of oxide colorants in transparent dielectric layer having color-filter function was systematically accessed. It was demonstrated that the optimized content of oxide colorants to parent glass could greatly increase up contrast ratio and color temperature without significantly degrading luminance.

• Laser Solutions
• /
• v.2 no.2
• /
• pp.27-33
• /
• 1999

Electron beam was applied on the low carbon steel in order to fabricate Metal/Metal GBM(Graded Boundary Material). Ni sheet was placed on the steel substrate. The electron beam was irradiated on the surface and produced a homogeous alloyed layer. Sequential repetition of electron beam treatments for 4 times resulted in 8mm thick graded layer. To determine each layers property, optical microscopy, XRD, microhardness tester and EDS were used. The residual stress was measured by the low angle x-ray diffraction method. The graded boundary layer was stepwise profile, but Ni content incresed up to 80 wt% and Fe content decreased 20 wt% near surface. Each layers microstructure and hardness varied by different Fe/Ni composition. The compressive residual stress was induced by martensite transformation in the 1st and End layers and the shrinkage cracks were formed in graded layer by rapid cooling.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.4
• /
• pp.162-167
• /
• 2012

Ni-P/C multi-layer was synthesized by electroless plating and paste coating for better corrosion and surface conductance as a metallic bipolar plate. The Ni-P layer could be synthesized with the range of 2.6~22.4 at.% P contents and it's surface morphology and corrosion resistance depend on content of P. Corrosion resistance of the Ni-P layer in sulfuric acid by electrochemical test is similar with pure Ni. Surface resistance of pure Ni after corrosion was increased about 8% compared to pure Ni. On the other hand, that of the Ni-P/C composite with 20% carbon content was increased only 1%.

• Korean Journal of Materials Research
• /
• v.8 no.10
• /
• pp.925-930
• /
• 1998

EPMA and XPS on $Bi_2Sr_2-\chi_LCa_1+\chi_LCu_2O_{8+d}$($\chi_L$ = 0.01, 0.2, 0.3, 0.4, 0.5, 0.6) films by LPE method were performed in order to investigate Sr and Ca distributions in SrO- and Ca-layers. It is found that $T_C^{zero}$ carrier concentration and lattice parameter c monotonically decreases with increasing $\chi_L$. Sr and Ca contents in Ca-layer change in proportion to that in melt. On the other hand, in SrO-layer, Ca content strongly depends on Sr content in that layer and not on Ca content in melt. Since deficiency in SrO-layer increases and $T_C^{zero}$ creases with $\chi_L$,t is found that the deficiencies of Sr and Ca atoms in the SrO-layer has a influence on reducing $T_C^{zero}$.

• Journal of Biosystems Engineering
• /
• v.16 no.3
• /
• pp.248-262
• /
• 1991

Simulation model was developed to analyze drying process for tray type red pepper dryer and validated by experiments. This model could predict satisfactorily temperatures and moisture contents of red pepper and temperatures of drying air during drying. Optimize algorithm was developed to search control valiables (drying air temperature, air recycle ratio and air flow rate) of red pepper dryer based on a criterion of minimizing energy consumption under the constraint conditions that statisfied carotenoid retension of at least 210mg per 100g dry matter, the moisture content of bottom layer of 15% (d.b) and drying time of less than 35 hours. Step changes in drying air temperature and air recycle ratio were considered in the optimization. In single step in control variables, the difference of the moisture content between top layer and bottom layer was great and more fan power was required. As the drying trays were exchanged when the moisture content of bottom layer reached to 100% (d.b), fifty percent of energy was saved and the difference of moisture content was little. In double step changes in control variables, optimal conditions were found by changing the step when the moisture content of bottom layer reached to 100% (d.b) (about 19.8 hours from starting drying). Optimum air flow rate was $18.1cmm/m^2$. Optimum drying air temperature and air recycle ratio in the first step was $55.8^{\circ}C$ and 0.80, and in the second step $65.6^{\circ}C$ and 0.88, respectively. In triple step changes in control variables, the optimal conditions were found by changing the steps when the moisture content of bottom layer reached to 250% (d.b) and 150% (d.b). Optimal air temperatures were $66.2^{\circ}C$, $58.4^{\circ}C$ and $66.9^{\circ}C$, and optimal air recycle ratios were 0.778, 0.785, 0.862 at each step, respectively. Optimal air flow rate was $18.9cmm/m^2$. The best operating mode was triple step mode considering energy consumption, drying time, fan power, and quality of dried red pepper. When the triple step mode was used to dry the red pepper, the energy consumption was about 16.5%~57.2% less than that of the single step mode and the drying time was 6.6 hours shorter than that of the double step mode.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.24-24
• /
• 2009

ENIG(Electroless Nickel Immersion Gold) is the surface treatment method that is used most widely at fine pitch's SMT and BGA packaging process. In this paper, we have studied the effect of P content variation during ENIG process on those phenomena related to the solder joint. The effect of P content was discussed using the results obtained from FE-SEM, EPMA, EDS and FIB. Finally, it was concluded that the more P-content in Ni layer, the thicker P-rich layer.