• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2006.06b
• /
• pp.339-344
• /
• 2006

The productivity for container hand1ing in container ship is a important role in container terminal, and it is mainly depended on the productivity of gantry crane. From the failure of gantry crane, the crane will be stopped until the repair of the failure. During the repair, the loading and/or discharging for container ship is suspended, and the productivities of the container ship and the yard is just hold. Thus, the prevention maintenance is importance to make a keep the steady state condition for all equipments in container terminal. In this paper, we deal with a optimal determination method of prevention maintenance interval for gantry crane systems. For verification, we will make a productivity of gantry crane and adapt to total container handling in each ship by simulation.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.6
• /
• pp.504-511
• /
• 2012

The objective of this study is to investigate tank container to be used as fuel tank for LNG fueled ship. Feasibility of tank container to the fuel tank of LNG fueled ship is addressed and the advantage of tank container as fuel tank of ship is investigated. Conceptual configuration of the tank container is designed as well as structural analyses based on finite element method are carried out to meet the design regulation suggested by shipping register. Static loading is considered by structural analysis and impact test is performed. It is necessary to require SRS(shock response spectrum) in order to investigate structural safety which can meet.

• Journal of the Korean Institute of Navigation
• /
• v.14 no.4
• /
• pp.1-15
• /
• 1990

With increasing ship's speed turnround and port time becomes a large percentage of total roundtrip time and this causes to accelerate the introduction of the various kind of modern handling equipment, the standardization of cargoes, and the improvement of the ship. However, it is still a drag on efficient operation of ship. Similarly, the turnround time at the container port is very important as a measure for the decision of the efficiency of port. To decrease operating coasts, the minimization of the time need to cargo handling at the ports of call must be achieved. Thus the optimization of the time need to cargo handling at the ports of call must be achieved. Thus the optimized Container Loading Plan is necessary, especially under the rapid speed of container operations. For the container loading plan, in this thesis, we use the hungarian method and the branch and bound method to get the initial disposition of both maximization of ship's GM and minimization of shift number to the obstructive container in a yard area. We apply the dynamic programming algorithm to get the final disposition for minimizing total turnroudn time and finally we analyzed the results to check whether the initial disposition is proper or not.

• Journal of Ocean Engineering and Technology
• /
• v.23 no.3
• /
• pp.14-19
• /
• 2009

The present study developed a model to estimate the light weight of an ultra-large container ship. The weight estimation model utilized container ship data obtained from shipyards and the subdivided this weight data into appropriate weight groups. Parameters potentially affecting the group weight were selected and expanded based on experience for weight estimation, and a correlation analysis was performed by the SPSS program to determine the key parameters characterizing the group weight. A weight estimation model applying the multi-regression analysis was proposed to assess the weight of an ultra-large container ship at the preliminary design stage, and the results obtained by the suggested method showed good agreement with the shipyard data.

• Journal of Ship and Ocean Technology
• /
• v.7 no.3
• /
• pp.56-65
• /
• 2003

The hull monitoring systems of container ships with four long-base gages give enough information for identifying the hull girder loads such as bending and torsional moments. But such a load-identification for container ships has not been known. In this paper, a load-identification method is suggested in terms of a linear matrix equation that the measured strain vector equals to the multiplication of the transformation matrix and the desired strain component vector. The equation is proved to be mathematically complete by the property of positive-definite determinant of the transformation matrix. The method is applied to a hull stress monitoring system for 8100TED container ship during sea trial, and the estimated external loads illustrate reasonable results in comparison with the pre-estimated results. This moment decomposition concept has also been tested in real operation conditions. The typical phenomena over the Suez Canal illustrated very suitable results comparing with the physical understandings. Henceforth, one can effectively use the proposed concept to monitor the hull girder loads such as bending and torsional moments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.41 no.11
• /
• pp.1446-1455
• /
• 2016

The recent increase of fresh farm products, hazardous cargos, and high-priced goods in marine transportation has caused an increased demand of cargo owners and shipping companies with regard to the monitoring of the location and state of cargo. To meet this increase, numerous technologies are being studied for the monitoring of the cargo state. Cargo containers on a ship are loaded on a ship's deck and in a ship's hold, which is located under the deck. However, Since the developed technologies mostly transfer the container status information that collected by mobile communication, it costs a lot to install communication infrastructure on ship. And the ship's hold is completely sealed with a cover, and communication with the reader positioned at the ship's bridge is difficult. Therefore, most existing studies on container monitoring on ships have focused on the monitoring of containers loaded on a ship's deck. Accordingly, this study suggested system configuration for the monitoring of containers in a ship's hold using IP-RFID technology. The suggested system configuration was tested on an actual ship under navigation, and the test results are given in this study. The test results verified that the monitoring of containers in a ship's hold using IP-RFID technology is effective.

• Journal of Advanced Research in Ocean Engineering
• /
• v.4 no.4
• /
• pp.174-184
• /
• 2018

We herein propose a new design procedure of a flexible container ship model where the vertical bending and torsional vibration modes are similar to its prototype. To achieve similarity in torsional vibration mode shapes, the height of the shear center of the model must be located below the bottom hull, similar to an actual container ship with large opening decks. Therefore, we designed a ship model by imparting appropriate stiffness to the hull, using urethane foam without a backbone. We built a container ship model according to this design strategy and validated its dynamic elastic properties using a decay test. We measured wave-induced structural vibrations and present the results of tank experiments in regular and freak waves.

• Journal of the Korea Society for Simulation
• /
• v.8 no.4
• /
• pp.61-72
• /
• 1999

This paper presents an estimation method of container handling capacity and selection of resource allocation strategies of container terminals using the computer simulation models. Simulation models are developed to model container terminal consisting of 4 berths considering the berth allocation strategies, crane allocation strategies and the total number of container cranes using Arena simulation package. The proposed models do not consider the yard operations and gate operations. All the input parameters for the models are estimated on the basis of the existing container terminal operation data and the planning data for the automated container terminal planned by Korean government. Four berth allocation strategies and three crane allocation strategies are considered. The total number of container cranes considered ranges from 12 to 15. Non-terminating simulation techniques are utilized for the performance comparison among alternatives. The performance measures such as average ship turnaround time, average ship waiting time, average ship service time, the number of containers handled per year, and the number of ships processed per year are used. The result shows that the berth allocation strategy minimizing the sum of the number of ships waiting, the number of busy container cranes and number of ships handled performs better than any other berth allocation strategies. In addition, the crane allocation strategy allocating up to 5 container cranes per berth performs better than any other crane allocation strategies. Finally there are no significant performance differences among the alternatives consisting of different total number of container cranes allocated.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.30 no.1
• /
• pp.118-126
• /
• 2024

In this paper, the research contents and results related to the automation of the hull-form optimal design of container ships are summarized. A container ship is a ship that generally operates near Froude number of 0.26. To implement hull-form optimal design automation for ships operating at this speed, an optimization algorithm, a hull-form change algorithm, a ship performance prediction algorithm, an automation algorithm, and an iterative calculation technique were applied to develop a numerical analysis computer program that enables hull-form optimal design automation of the container ship, and it was named HOTCONTAINER. In this study, a sensitivity analysis algorithm was developed and applied to appropriately set design variables for hull-form optimal design. To understand the reliability and real ship applicability of the developed algorithm, a numerical analysis was performed on KCS(KRISO Container Ship), a container ship that has been studied in various ways worldwide. Consequently, the optimal ship was derived, and the wave resistance, wave pattern, and wave height of the target and optimal ship were compared. In conclusion, compared the target ship, the optimal ship a 47.63% decrease in wave resistance, and the displacement and wet surface area decreased by 0.50% and 0.39%, respectively.

• Journal of the Korea Society for Simulation
• /
• v.10 no.2
• /
• pp.33-46
• /
• 2001

Recently, the usage of containers in marine transportation is rapidly increasing. The problem of ship stability is important because of its direct influence to the loss of the human-life, ship, and merchandise. However, the assessment for ship stability during container loading/unloading in port is dependent on human experience only. On the other hand, the emerging information and communication technologies of shipbuilding industrial environments are rapidly changing. To respond to the situation, a new paradigm has been matured with new concepts such as the concrete method. Especially, all the efforts are shown to be concentrated to realize the concept of Simulation Based Design(SBD) based on three dimensional Computer Aided Design(CAD) model. In this paper, ship model-based simulation methodology for design and operation of ship is suggested, and for the verification of suggested methodology, the system for stability assessment of ship during container loading/unloading was developed using ENVISION, a general-purpose simulation system. The developed system consists of geometric modeling subsystem, basic calculation subsystem, and Computer Aided Engineering(CAE) subsystem. In addition, interface to CAE/CAD /simulation system such as SIKOB and ENVISION is provided.