• 대한기계학회논문집B
• /
• 제35권11호
• /
• pp.1147-1156
• /
• 2011

CLECDiS 는 면적변화형 정전용량 센서의 단점을 극복하고 나노미터 수준의 분해능으로 밀리미터 이상의 큰 변위를 측정하도록 개발된 접촉식 변위센서이다. 그러나 접촉구동 특성으로 인하여 표면평탄도와 마찰에 의해 작은 접촉상태의 변화에도 출력 신호는 크게 왜곡될 수 있어 실제 이를 활용하기 위해서는 전극간 접촉상태를 안정적으로 유지하는 것이 중요하다. 이에 본 연구에서는 전극간 접촉상태의 변화에 따른 신호의 왜곡 특성을 실제 출력 신호와 비교하여 분석하고, 접촉면 내 압력 분포와 센서의 운동 오차 측정을 통해 접촉상태의 변화를 파악하였다. 이를 통하여 센서의 운동 오차와 마찰력의 영향을 최소화하기 위한 접촉 유지 기구를 설계하고 제작하였으며 이를 이용한 구동실험을 통해 보다 안정적인 센서 출력 신호를 획득하였다.

• KSTLE International Journal
• /
• 제3권2호
• /
• pp.79-83
• /
• 2002

Sealing an oil-air mixture plays important roles to have an enhanced lubrication for high speed spindle. High speed spindle requires non-contact type of sealing mechanism. Current work emphases on the investigation of the air jet effect on the protective collar type labyrinth seal. To improve the sealing capability of conventional labyrinth seal, air jet was injected against through the leakage flow, It has a combined geometry of a protective collar type and an air jet type. Both of a numerical analysis by CFD (Computational Fluid Dynamics) and experimental measurements are carried out to verify sealing improvement The sealing effects of the leakage clearance and the air jet magnitude are studied in various parameters. The results of pressure drop in the experiment match reasonably to those of the simulation by introducing a flow coefficient Effect of sealing improvement is explained as decreasing of leakage clearance by air jetting. Thus, sealing effect is improved by amount of air jetting even though clearance becomes larger.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권4호
• /
• pp.618-623
• /
• 2004

This paper has dealt with the heat storage characteristics of gel type micro size latent heat storage material slurry. The heat release operation to the gel type micro size latent heat storage material slurry was carried out using hot air bubbles by direct contact heat exchange. This experiment was carried out using phase change material of n-paraffin so the heat release amount is higher than cold water system. The parameters of this experiment were concentration of latent heat phase change material, height of heat release bath and inlet velocity of hot air. The main results obtained are as follows : (1) The effect of concentration of latent heat phase change material dispersed with water is very affective to the direct contact heat exchange between hot air and gel type micro size latent heat storage material slurry. (2) It is clarified that the most effective concentration of latent heat phase change material dispersed with water exists around 20mass% at this type of direct heat exchange model experiment.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 춘계학술대회 논문집 초전도 자성체
• /
• pp.25-28
• /
• 2002

Contact type Ic measurement system is needed to measure Ic continuously for long Bi-2223 tapes. Voltage and current terminals were designed several shapes for 4-probe method Ic measurement. Voltage terminals were made with brass and current terminals were made with Cu. We used 2 kinds of Bi-2223 tapes with different strength. When we measured Ic of Bi-2223 tape with Ag-Mg sheath, The proper weight was 0.3 kg and sharp pin type was better. according to voltage terminal shape and load. In case of Bi-2223 tape with Ag-Mn sheath, the proper terminal weight was 4 kg and sharp pin type was bad. It was possible to make continuous contact type Ic measurement system because We could get proper data - terminal shapes and loads - through these experiments.

• 소성∙가공
• /
• 제20권2호
• /
• pp.99-103
• /
• 2011

Many parameters influence the frictional behavior of steel sheet during stamping. The contact pressure between a die and a sheet during stamping is one of them. Thus, this parameter is investigated for high strength steel (HSS) sheets, which are widely used for auto body panels due to their potential for weight reduction. Since HSS extend the limits of contact pressure for mild steel, the effect of this parameter on friction cannot be ignored. To investigate the influence of contact pressure on the frictional behavior of steel sheets, a flat type of friction test was conducted on three different steel sheets under various contact pressures. For bare steel sheets, the curve representing the relationship between contact pressure and friction coefficient exhibits a U shape. Coated steel sheets show a similar tendency except at low contact pressure. For these materials, when the contact pressure is very low, the friction coefficient slightly increases with pressure before it starts to decrease. The test results show that the effect of contact pressure on frictional behavior of steel sheet is not negligible even for contact pressures that are lower than the strength of HSS sheet.

• 한국생산제조학회지
• /
• 제20권6호
• /
• pp.756-760
• /
• 2011

This paper proposed an alignment stage driven by piezo actuators for alignment process of a contact-type lithography. Among contact-type lithography processes, an UV-curable nanoimprint process is an unique process to be able to align patterns on upper and lower layers. An alignment stage of the UV-curable nanoimprint process requires nano-level resolution as well as high stiffness to overcome friction force due to contact moving. In this paper, the alignment stage consists of a compliant mechanism using flexure hinges, piezo actuators for high force generation, and capacitive sensors for high-resolution measurement. The compliant mechanism is implemented by four prismatic-prismatic compliant chains for two degree-of-freedom translations. The compliant mechanism is composed of flexure hinges with high stiffness, and it is directly actuated by the piezo actuators which increases the stiffness of the mechanism, also. The performance of the ultra-precision stage is demonstrated by experiments.

• 한국안전학회지
• /
• 제20권1호
• /
• pp.1-6
• /
• 2005

Stick type ignition coil is new development that connect directly with ECU(Electronic control unit), without needing a spark plug cable and distributor. Glass-fiber reinforced ploymeric composites provide the desirable properties of high stiffness and strength as well as low specific weight. Stick type ignition coil jacket is using PBT CF30 resin. PBT CF30 resin is a kind of electric insulation which is a superior engineering plastic that is used to prevent the leakage of the electrical current. If PET receive a mistake of design or excessive force when HV terminal oppress on jacket, it can happen to crack. Local stress concentrations occurring on the contact surface, the contact phenomenon becomes a direct cause to the wear and failure of mechanical structures. When it is cracked, it can allow a leakage of the electrical current. So, in this study, we analyze the contact stress to PBT jacket using ANSYS program, when HV terminal oppress on jacket. We suppose PBT to be Jacket and we analyzed contact stress that happens in PET like PBT analysis method. We compared the use of PBT and PET.

• 지역사회간호학회지
• /
• 제14권3호
• /
• pp.468-478
• /
• 2003

Purpose: The purpose of this study is to identify the relationship among sexual contact, sex role identification, and self esteem in Korean girls' high school students. Methods: The data were collected from 522 girls, who were stratified samples from a target population of 63,375 11th grade students from 200 regular high schools and 70 vocational high schools in Seoul, Korea from June 22 to July 18, 2002. Data were processed with the SAS program. Results: It was found that 42.51% of girls haven't experienced any sexual contact at all. The highest frequency in the final level of sexual contact was 'kiss', which was 22.03%. The 'androgyny' type among sex role identities of girls was most common, 32.57%, being followed by the 'undifferentiated' type 31.61%, the 'masculinity' type 18.97%, and the 'femininity' type 16.86, in that order. The sexual contacts such as 'holding hands', 'arms around', 'embracing', and 'kiss' were significantly different depending on sex role identity types. The score for self-esteem was significantly different depending on sex role identity types. The score for self- esteem was not significantly different depending on the final level of sexual contact. Conclusion: Based on the findings of this study, sex education programs should be developed in order to delay the sexual contacts of girls.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.603-606
• /
• 2000

This dissertation is concerned with ultra-precision profile measurement of aspheric surfaces using contact probing technique. A contact probe has been designed as a sensing device to obtain measuring resolutions in nanometer regime utilizing a leaf spring mechanism and a capacitive-type sensor. The contact probe is attached on the z-axis during measurement while aspheric objects are supported on an precision xy-stage whose lateral motions are monitored by a set of two orthogonal plane mirror type laser interferometers. Experimental results show that the contact probing technique developed in this investigation is capable of providing a repeatability of 50 nanometers with a $\pm$3$\sigma$ uncertainty of 300 nanometers. Thermal disturbance is found the most significant factor that should be precisely controlled for accurate measurement.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.310-315
• /
• 2001

The most general feature of contact zone among the mechanical components is elliptical circle. In particular, continuously variable transmission (CVT) of toroidal type has elliptical shape of contact zone under the elastohydrodynamic lubrication condition, where the power is transmitted by the shearing the efluid. Due to the traction of the shear behaviors of lubricant over the small elliptical contact zone, high power of torque is transmitted. During the power transmission, many kinds of mechanical movements occur such as squeezing, sliding, rolling and spinning. The spinning effect that is not common contact behavior in tribological components frequently makes significant abnormal wear damage. In this work, the analysis of elliptical contact of elastohydrodynamic lubrication with spin effect is performed, which will give very useful information to understand the traction behaviors in toroidal type of CVT system.