• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집 Vol.14 No.1
• /
• pp.521-524
• /
• 2001

In this letter. we report on the investigation of Ti. Pt/Si/Ti Ohmic contacts to p-type 4H-SiC. The contacts were formed by a 2-step vacuum annealing at $500^{\circ}C$ for 1h. $950^{\circ}C$ for 10 min respectively. The contact resistances were measured using the transmission line model method. which resulted in specific contact resistivities in the $3.5{\times}10^{-3}$ and $6.2{\times}10^{-4}ohm/cm^{2}$, and the physical properties of the contacts were examined using x-ray diffraction. microscopy. AES(auger electron spectroscopy). AES analysis has shown that, at this anneal temperature, there was a intermixing of the Ti and Si. migration of into SiC. Overlayer of Pt had the effect of decreasing the specific contact resistivity and improving the surface morphology of the annealed contact.

• Tribology and Lubricants
• /
• 제25권4호
• /
• pp.231-235
• /
• 2009

In this study, the influence of contact pressure on the variation in coefficients of friction between porcine knee joint cartilage and Co-Cr alloy in a repeat pass sliding motion was investigated. Flat-ended cartilage pin specimens(9 mm diameter, 8 mm long) were prepared from porcine(6 months old) knee joints by a drill-type punch. Friction tests were conducted by using a pin-on-disk type friction tester for an hour in PBS lubricated condition under the contact pressures of 0.5, 1 and 2 MPa with 50 mm distance per a cycle at ambient condition. As a result, coefficients of friction increased as the test duration increased for all contact pressures. The maximum coefficients of friction were 0.082, 0.06 and 0.098 for 0.5, 1, and 2 MPa, respectively. It showed that coefficients of friction of porcine knee joint cartilage against Co-Cr alloy depended on the level of contact pressure and related to squeeze film lubrication mechanism.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.521-524
• /
• 2001

In this letter, we report on the investigation of Ti, Pt/Si/Ti Ohmic contacts to p-type 4H-SiC. The contacts were formed by a 2-step vacuum annealing at 500$^{\circ}C$ for 1h, 950$^{\circ}C$ for 10 min respectively. The contact resistances were measured using the transmission line model method, which resulted in specific contact resistivities in the 3.5x10$\^$-3/ and 6.2x10$\^$-4/ ohm/$\textrm{cm}^2$, and the physical properties of the contacts were examined using x-ray diffraction, microscopy, AES(auger electron spectroscopy). AES analysis has shown that, at this anneal temperature, there was a intermixing of the Ti and Si, migration of into SiC. Overlayer of Pt had the effect of decreasing the specific contact resistivity and improving the surface morphology of the annealed contact.

• Toxicological Research
• /
• 제26권2호
• /
• pp.123-130
• /
• 2010

The effect of DHU001, a mixed herbal formula consisted of 7 types aqueous extracts for various respiratory disorders were evaluated on 2,4-dinitrofluorobenzene (DNFB)-induced contact dermatitis, type I allergic model. Contact dermatitis was induced by sensitization with dinitrophenyl-derivatized ovalbumin (DNP-OVA) and DNFB challenge as antigen. Two different dosages of DHU001 (300 and 150 mg/kg) were orally administered to DNP-OVA sensitization mice once a day for 7 days with reference material, dexamethasone (15 mg/kg, intraperitoneal treatment). End of 7 days oral administration of DHU001 extracts or intraperitoneal treatment of dexamethasone, the changes on the edematous changes and scratching behavior were measured. Immediate after DNFB challenge on ear or paw of DNP-OVA sensitized mice, increases of ear and paw thicknesses and weights were detected with anterior ear skin (dermis to epidermis) thickness and paw scratching behavior increases. However, these contact dermatitis signs induced by DNFB treatment were reduced by treatment of the both different dosages of DHU001 and dexamethasone, respectively. The results obtained in this study suggest that oral treatment of DHU001 extracts also has relatively favorable effects on contact dermatitis.

• 한국전기전자재료학회논문지
• /
• 제22권9호
• /
• pp.717-723
• /
• 2009

Ni/Al ('/' denotes deposition sequence) contacts were deposited on Al-implanted 4H-SiC for ohmic contact formation, and the conduction properties were characterized and compared with those of Ni-only contacts. The thicknesses of the Ni and Al thin film were 30 nm and 300 nm, respectively, and the films were sequentially deposited bye-beam evaporation without vacuum breaking. Rapid thermal anneal (RTA) temperature was varied as follows : $840^{\circ}C$, $890^{\circ}C$, and $940^{\circ}C$. The specific contact resistivity of the Ni contact was about $^{\sim}2\;{\pm}\;10^{-2}\;{\Omega}{\cdot}cm^2$, However, with the addition of Al overlayer, the specific contact resistivity decreased to about $^{\sim}2\;{\pm}\;10^{-4}\;{\Omega}{\cdot}cm^2$, almost irrespective of RTA temperature. X-ray diffraction (XRD) analysis of the Ni contact confirmed the existence of various Ni silicide phases, while the results of Ni/Al contact samples revealed that Al-contaning phases such as $Al_3Ni$, $Al_3Ni_2$, $Al_4Ni_3$, and $Ab_{3.21}Si_{0.47}$ were additionally formed as well as the Ni silicide phases. Energy dispersive spectroscopy (EDS) spectrum showed interfacial reaction zone mainly consisting of Al and Si at the contact interface, and it was also shown that considerable amounts of Si and C have diffused toward the surface. This indicates that contact resistance lowering of the Ni/Al contacts is related with the formation of the formation of interfacial reaction zone containing Al and Si. From these results, possible mechanisms of contact resistance lowering by the addition of Al were discussed.

• 한국의류학회지
• /
• 제18권2호
• /
• pp.180-188
• /
• 1994

The purpose of this study was to evaluate the effect of basic needs and demographic variables of adult woman on the modesty and aethetics In the selection of clothes. The results of the study were as follows: 1. There are factors which have effect on variables of need. School careers have effect on physical need. Age, marriage status and household type have effect on safty need. Native community and household type have effect on self-esteem. School career, native community, household type and frequency of contact with mass media have effects on need of self-actualizing and native community has effect on the aesthetic need. 2. Physical bleed, self-esteem, self-actualization, safety need, fiequency of contact with mass media, age, native community and income have direct effect on the modesty of clothing. 3. Aethetic and self-actualization need, frequency of contact with mass media and income have direct effect on the aethetics of clothing.

• Journal of the Optical Society of Korea
• /
• 제12권2호
• /
• pp.93-97
• /
• 2008

The superposing angle of the viewing zone forming optics and the display panel in the contact type 3 dimensional imaging systems for minimizing $moir{\acute{e}}s$ is found for a rectangular shape pixel with different aspect ratios. The angles are $26.2609^{\circ}$ for square shape pixels and $13.9858^{\circ}$ for the rectangular with aspect ratio 2. These angles result in the $moir{\acute{e}}s$ with the smallest period for the respective aspect ratio. The effectiveness of the angles is also experimentally demonstrated.

• ETRI Journal
• /
• 제27권4호
• /
• pp.433-438
• /
• 2005

We present a new type of silicon micro-probe card using a three-dimensional probe beam of the cantilever type. It was fabricated using KOH and dry etching, a porous silicon micromachining technique, and an Au electroplating process. The cantilever-type probe beam had a thickness of $5 {\mu}m$, and a width of $50{\mu}$ and a length of $800 {\mu}m$. The probe beam for pad contact was formed by the thermal expansion coefficient difference between the films. The maximum height of the curled probe beam was $170 {\mu}m$, and an annealing process was performed for 20 min at $500^{\circ}C$. The contact resistance of the newly fabricated probe card was less than $2{\Omega}$, and its lifetime was more than 20,000 turns.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.65.5-65
• /
• 2001

In this study, we have designed and fabricated the slidacs type automatic voltage regulator(AVR) that is able to control the output voltage continuously according to road variation. Especially, the frictions between the surface of contact of the slidacs coils and the output wire moving rod are reduced by transforming the mechanical configuration of surface of contact of slidacs from the conventional sliding one into the proposed rotary one composed of cylindrical bearing. Thus, the slidacs type AVR using cylindrical bearing proposed in this study has less noise than conventional one owing to the reduction of frictions, and its breakdown ratio caused by the abrasion of contact materials is reduced. Furthermore, ...

• 한국결정성장학회:학술대회논문집
• /
• 한국결정성장학회 1997년도 Proceedings of the 12th KACG Technical Meeting and the 4th Korea-Japan EMGS (Electronic Materials Growth Symposium)
• /
• pp.231-236
• /
• 1997

To improve electrical properties and uniformity of high-low doped n-type GaAs, new ohmic contacts with a low-resistance and the superior uniformity was developed using a concept of hybrid ohmic contact. The hybrid ohmic contact displayed good surface and interface morphology and had minimum contact resistivity of 3${\times}$10-6 $\Omega$$\textrm{cm}^2$ in a wide annealing temperature ranged from 340$^{\circ}C$ to 420$^{\circ}C$, which was much wider than that of conventional ohmic contacts. The microstructural analysis showed that the Pd/Ge ohmic contact at low annealing temperature (∼300$^{\circ}C$) and also annealing temperature (∼400$^{\circ}C$), resulting ij hybrid ohmic contacts.