• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.11
• /
• pp.968-972
• /
• 2008

Ni/Ti/Al multilayer system ('/'denotes the deposition sequence) was tested for low-resistance ohmic contact formation to Al-implanted p-type 4H-SiC. Ni 30 nm / Ti 50 nm / Al 300 nm layers were sequentially deposited by e-beam evaporation on the 4H-SiC samples which were implanted with Al (norminal doping concentration = $4\times10^{19}cm^{-3}$) and then annealed at $1700^{\circ}C$ for dopant activation. Rapid thermal anneal (RTA) temperature for ohmic contact formation was varied in the range of $840\sim930^{\circ}C$. Specific contact resistances were extracted from the measured current vs. voltage (I-V) data of linear- and circular transfer length method (TLM) patterns. In constrast to Ni contact, Ni/Ti/Al contact shows perfectly linear I-V characteristics, and possesses much lower contact resistance of about $2\sim3\times10^{-4}\Omega{\cdot}cm^2$ even after low-temperature RTA at $840^{\circ}C$, which is about 2 orders of magnitude smaller than that of Ni contact. Therefore, it was shown that RTA temperature for ohmic contact formation can be lowered to at least $840^{\circ}C$ without significant compromise of contact resistance. X-ray diffraction (XRD) analysis indicated the existence of intermetallic compounds of Ni and Al as well as $NiSi_{1-x}$, but characteristic peaks of $Ti_{3}SiC_2$, a probable narrow-gap interfacial alloy responsible for low-resistance Ti/Al ohmic contact formation, were not detected. Therefore, Al in-diffusion into SiC surface region is considered to be the dominant mechanism of improvement in conduction behavior of Ni/Ti/Al contact.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.10
• /
• pp.87-93
• /
• 1994

Ohmic contacts between Au and p-HgHg_{0.7}Cd_{0.3}Te$ with low specific contact resistance have been obtained. The contact region of the wafer is first pre-heated for 5 seconds in a rapid thermal processing equipment. The temperature reaches a maximum value of about 200$^{\circ}C$ at the end of the 5 seconds. Next, a thin Au film is formed on the contact region by immersing the sample in AuCl$_{3}$ solution. the sample is then post-annealed in the same condition as the pre-heating after Pb/In pad metals are deposited on the electroless Au contacts. The specific contact resistance measured by transmission line model is 5${\times}10^{-3}{\Omega}cm^{2}$ at 80K. RBS and differential Hall measurement data suggest that the above low resistance ohmic contact is ascribed to surface traps and increased gold diffusion rate.

• Journal of Oral Medicine and Pain
• /
• v.17 no.1
• /
• pp.41-50
• /
• 1992

The authors performed a experimental study to evaluate the effects of masticatory muscle fatigue on tooth contact and masticatory muscle activity in 26 normal healthy women. The experimental masticatory muscle fatigue was induced by unilateral biting of 5kg force on mandibular first molar. The results were as follows : 1. The initial symptom related to muscle fatigue pain appeared in 85.19 seconds of isometric contraction and the endurance time of isometric contraction was 203.15 seconds. 2. The pain occurred more frequently in masseter region than in temporal region. In masseter pain the incidence was almost equal between both sides, whereas the temporal pain was more in contralateral side. 3. The spontaneity and the symmetry of tooth contact during maximum clenching were reduced after isometric unilateral biting. 4. After induction of experimental muscle fatigue, the EMG activities of masseter muscles of both sides and ipsilateral temporal muscle showed the tendency of decreasing activities. 5. The asymmetry indicies of masseter and temporal muscles were reduced after isometric bilateral biting.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.195-196
• /
• 2002

Studied is fretting wear behaviour of transversely vibrating tube which is supported by springs and dimples. This simulates the fuel rod fretting due to flow-induced vibration in a nuclear reactor. The contact between spacer grid springs and fuel cladding tubes arc brought into focus in this paper. From the mechanical viewpoint, a concave contact shape of spring is considered to perform a wider distribution of the contact stress. Sliding/impacting experiments are conducted in air at room temperature with the conditions of positive contact force and gap existence to accommodate the mechanical condition between the fuel rod and the grid spring during reactor operation. It is found that wear region is separated and wear volume becomes larger as the supporting condition becomes poorer. Spring and dimple cause similar wear.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.8
• /
• pp.2026-2038
• /
• 1994

A numerical scheme is developed for the analysis of incipient sliding contact with orthotropic friction condition subjected to tangential load and twisting moment. The inherent nonlinearity in the orthotropic friction law has been treated by a polyhedral friction law. Then, a three-dimensional linear complementarity problem(LCP) formulation in an incremental form is obtained, and the existence of a solution is investigated. A Lemke's complementary pivoting algorithm is used for solving the LCP. The scheme is illustrated by spherical contact problems, and the effects of eccentricity of elliptical friction domain on the traction and stick region are discussed.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.11a
• /
• pp.133-136
• /
• 2007

In this work, 3-dimensional, non-isothermal numerical simulation was performed to analyse the effects of contact resistance and electric conductivity of GDL on the fuel cell performance. For numerical simulation contact resistance of Carbon and Stainless steel was measured. The simulation results reveal that 10 times change of electric conductivity leads only 6.5% decrease of PEMFC performance. But stainless steel which has high contact resistance decrease fuel cell performance over 25% at a high current density region than carbon. This results show that suitable Surface treatment technology is needed for metal bipolar plate, especially stainless steel.

• Proceedings of the KSME Conference
• /
• 2000.04a
• /
• pp.731-736
• /
• 2000

An optimal design method is adopted for a spacer grid in nuclear power plant. It is made of punched sheet metal process, functioning as springs and dimples supporting fuel rods. For stress analysis of the assembled fuel rod support, a typical cell out of the repeated pattern in the assembly is modeled using 4-node shell elements. A commercial code, ABAQUS, is used for detailed analysis of contacting phenomena with friction. For the optimization, design varibles are taken from geometric parameters representing the shape of the bent leaf spring part and mating contact region with fuel rod. Objective function is considered in relation to mechanical functions and durability. Maximum yon Mises stress is considered in relation to constrained contact stress.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1999.11a
• /
• pp.323-330
• /
• 1999

The conventional analysis for the numerical computation of fluid film thickness with elastic deformation of contact region. is performed by Newton-Rephson method for its 18st convergence characteristics. However, both high load and relatively low sliding velocity frequently make it impossible for Newton-Rahpson method to get both converged and stable solutions. In particular, this method cannot provide converged Solution under the condition of high load above 1.0 GPa which frequently occurs in line contact of EHL problem. Multigird multi-level method for the solver of non-linear partial differential equation including solid deformation is preferred to Newton-Rshpson method for better convergence and stability and is applied to line contact EHL behavior in this study.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.7 no.5
• /
• pp.38-45
• /
• 1998

The Z-map model which is quite similar to the non-parametric patch is widely used to describe the shape of a surface because of its simplicity. Despite the inherent advantage of z-map model. it has drawbacks that there exists difficulty in expressing the vertical walls and its related contact treatment method. In the region of vertical walls, there is a convergence problem in searching the contact point. In this study a contact point finding scheme is presented, based on the z value of the z-map model on the sheet normal direction. To show the utility of this scheme a compared with the experimental results. The effects of the Z-map grid distances and the interpolations of the inside Z-map value are also discussed.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1897-1902
• /
• 2004

Numerical analysis of the heat transfer associated with droplet impact on a hot solid surface is performed by solving the mass, momentum and energy equations for the liquid-gas region. The deformed droplet shape is tracked by a level set method which is modified to achieve volume conservation during the whole calculation procedure and to include the effect of contact angle at the wall. The numerical method is validated through test calculations for the cases reported in the literature. Based on the numerical results, the effects of advancing/receding contact angle, impact velocity and droplet size on the heat transfer during droplet impact are quantified.