• Tribology and Lubricants
• /
• 제12권3호
• /
• pp.12-25
• /
• 1996

The friction and wear behaviors of ceramics against steels with lubricants were investigated and compared with those observed in air. Lubrications wbre done by a water and a commercial engine oil as received. The investigated ceramics were $Al_{2}O_{3}$, SiC, and $Si_{3}N_{4}$. Steels with 0.2 wt.% C were heat treated to obtain tempered structure. A cylinder-on-plate tribometer with rotated sliding motion was used to carry out the experiments. In the experiments reported here, the ranges of different testing speeds and loads were used. It was found that the friction and wear characteristics of tested pairs were significantly influenced by environments. In water and oil environments the wear of ceramics was reduced from 10$^{-6}$ g/s down to 10$^{-8}$ g/s in dry sliding at the same values of the frictional power which are the products of the friction coefficient, the load and the sliding speed. SiC showed excellent wear resistant behavior in water sliding, which was the lowest among tested ceramics, but it was, very poor in oils. In case of $Si_{3}N_{4}$, the wear rates were very low under oil environment, but the highest in water. The wear rates of $Al_{2}O_{3}$ were very low in both lubricating conditions at low values of the frictional power, but high at high values of the frictional power.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1988-1990
• /
• 1996

In this work, we have grown or evaporated thermal oxide and E-beam oxide on the (100) oriented n-type silicon wafers, respectively and they were directly bonded with another silicon wafer after hydrophilization using solutions of three types of $HNO_3$, $H_{2}SO_{4}$ and $NH_{4}OH$. Changes of average surface roughness after hydrophilizations of the single crystalline silicon wafer, thermal oxide and E-beam evaporated silicon oxide were studied using atomic force microscope. Bonding interfaces of the bonded pairs were inspected using scanning electron microscope. Void and non-contact area of the bonded pairs were also inspected using infrared transmission microscope.

• 드라이브 ㆍ 컨트롤
• /
• 제17권4호
• /
• pp.141-151
• /
• 2020

The aim of this study was to analyze the safety factor of range-shift gear pairs on multi-purpose agricultural implement machinery for an optimal design of a transmission system. Gear-strengths such as bending and contact stress and safety factors were analyzed under three load conditions: an equivalent engine torque at plow tillage, a rated engine torque, and the maximum engine torque. Root and contact safety factor were calculated to be 3.88, 5.14, 2.24, 2.11, 2.21, 0.99 and 0.78, 0.94, 0.65, 0.68, 0.84, 0.85, respectively, under equivalent engine torque condition at the plow tillage. The root and contact safety factor were calculated to be 1.91, 2.53, 1.10, 1.04, 1.07, 0.48 and 0.55, 0.66, 0.46, 0.48, 0.59, 0.59, respectively, under rated engine torque condition. The root and contact safety factor were calculated to be 1.60, 2.11, 0.92, 0.87, 0.90, 0.40 and 0.51, 0.61, 0.42, 0.44, 0.54, 0.54, respectively, under the maximum engine torque condition. The multi-purpose agricultural implement machinery could be conducted under plow tillage operation. However, gear specifications for tooth surface need modification because the gear surface would be broken at all driving conditions as safety factors are lower than 1.

• 대한간호학회지
• /
• 제30권5호
• /
• pp.1133-1144
• /
• 2000

This study was conducted to evaluate the effects of the program for the autistic children which was designed to promote mother-child attachment. The subjects of this study were consisted of 11 pairs of mother and child( 7 for participant group:PG, 4 for non-participant group: NPG), who were diagnosed as Pervasive Developmental Disorder. The intervention was consisted with play activity centered mother-child interaction, educational activity for mothers, lecture, video-feedback, and supports. The main data were collected by video-taping and analyzed by Wilcoxon Rank Sign Test, and Content Analysis. The results obtained were as follows, 1. Before the program, there were no significant group differences on the children's and the mother's characteristics. After the program, total score on the attachment of PG was higher than that of NPG, but not significant. Only proximity-seeking behaviors and contact-maintaining behaviors were higher significantly(p<.05). Then the characteristics on contact- maintaining behaviors of PG were lasting longer and reciprocal than those of NPG. 2. After the program, the score on mother's nurturing behavior of PG was significantly more increased. The mother's behaviors to her child of PG became more child- centered, positively responsive, expressive supportively. But there were pretty big individual difference. It can be concluded that Mother-child Attachment Promotion Program is effective. Thus it can be recommended to be a early intervention model for autistic children.

• Computers and Concrete
• /
• 제25권3호
• /
• pp.255-266
• /
• 2020

This study presents comparation of fixed and viscos boundary condition effects on three-dimensional earthquake response and performance of a RCC dam considering linear and non-linear response. For this purpose, Cine RCC dam constructed in Aydın, Turkey, is selected in applications. The Drucker-Prager material model is considered for concrete and foundation rock in the nonlinear time-history analyses. Besides, hydrodynamic effect was considered in linear and non-linear dynamic analyses for both conditions. The hydrodynamic pressure of the reservoir water is modeled with the fluid finite elements based on the Lagrangian approach. The contact-target element pairs were used to model the dam-foundation-reservoir interaction system. The interface between dam and foundation is modeled with welded contact for both fixed and viscos boundary conditions. The displacements and principle stress components obtained from the linear and non-linear analyses are compared each other for empty and full reservoir cases. Seismic performance analyses considering demand-capacity ratio criteria were also performed for each case. According to numerical analyses, the total displacements and besides seismic performance of the dam increase by the effect of the viscous boundary conditions. Besides, hydrodynamic pressure obviously decreases the performance of the dam.

• 한국소음진동공학회논문집
• /
• 제17권3호
• /
• pp.235-240
• /
• 2007

In this work, the operational deflection shape(ODS) of an automobile exhaust system is measured by using a recently-developed magnetic sensor. The magnetic sensor is composed of a solenoid and two pairs of permanent magnets generating an antisymmetric magnetic field in the lateral direction inside the solenoid. Lateral movement of a ferromagnetic pipe inside the magnetic field of the suggested sensor induces an electromotive force in the solenoid corresponding to the lateral velocity of the pipe. Due to the simplicity and non-contact characteristics of the magnetic sensor, dynamic behaviors of the structures operating under high temperature such as an exhaust pipe can be efficiently observed. It is shown that the lateral ODS of an exhaust system can be successfully measured by the suggested sensors.

• 한국기계가공학회지
• /
• 제21권2호
• /
• pp.64-72
• /
• 2022

Gear designers need to select the proper tolerances for deviations in both the center distance and parallelism of axes because these deviations cause high stresses and lead to fatigue breakage of the teeth. In this study, a three-dimensional finite element analysis model was developed for a helical gear used in metro vehicles, and a bending stress analysis method for gear pairs was established according to the contact position change. Using this model, the effect of shaft misalignment due to the center distance and shaft parallelism deviations on the bending stress of the gear was analyzed. As a result, the magnitude of the bending stress changed nearly linearly with the change in the center distance deviation. The tooth contact of the helical gear is biased toward the end of the tooth width when the parallelism deviations of the shaft occur, and the tooth root bending stress increases.

• Tribology and Lubricants
• /
• 제39권2호
• /
• pp.43-48
• /
• 2023

In this study, we investigate the tribological behavior of AISI 304 stainless steel pairs under deionized water and hexagonal boron nitride (h-BN) water dispersion lubrication. The specimen friction and wear properties are evaluated using a reciprocating ball-on-flat tribometer. The coefficient of friction remains nearly constant throughout the test under both lubricant conditions. The wear depth of the specimens under h-BN lubrication is smaller than that under deionized water lubrication, indicating the inhibition behavior of h-BN nanolubricants on direct metal-metal contacts. Optical micrographs and stylus profilometer measurements are performed to evaluate the severity of damage caused by the sliding motion and to determine the wear morphology of the specimens, respectively. The results show that h-BN nanolubricants does not have a significant effect on the friction behavior but demonstrates reduced wear owing to their trapping effect between the sliding interfaces. Moreover, scanning electron microscopy and energy-dispersive X-ray spectroscopy images of the specimens were acquired to confirm the trapping effect of h-BN between the sliding interfaces. The results also suggest that the trapped lubricants can distribute the contact pressure, reducing the wear damage caused by the metal-metal contact at the interface. In conclusion, h-BN nanolubricants have potential as an anti-wear additive for lubrication applications. Further investigation is needed to provide direct evidence of the trapping effect of h-BN nanoparticles between the sliding interfaces. These findings could lead to the development of more efficient and effective lubricants for various industrial applications.

• Asian-Australasian Journal of Animal Sciences
• /
• 제23권4호
• /
• pp.537-542
• /
• 2010

The goal of this study was to investigate how spectrographic features of ultrasonic vocalizations (USVs) in rats vary among individuals and behaviors. Eighteen pairs of rats were allocated to individual pair cages. Each pair's behaviors and vocalizations were recorded during the 900s a known cage-mate was returning to the cage. The effects of individuals, behaviors, and the interaction between individuals and behaviors ($individuals{\times}behaviors$) were tested on the duration and peak frequencies. There was difference in the duration and peak frequency: i) among individuals (p<0.0001 and p<0.0001, respectively); ii) among behaviors (p = 0.0667 and p<0.0001, respectively); iii) among individuals${\times}$behaviors (p<0.0001 and p<0.0001, respectively). The frequency of ultrasonic vocalizations changed with a frequency ranging from 40 to 71 kHz which were emitted by individuals, whereas the frequency of ultrasonic vocalizations changed with a frequency ranging from 60 to 70 kHz which were emitted by behaviors. The peak frequency of call on 'contact' behavior was lower than that of call on other behaviors, but call duration of call on 'contact' was longer than on other behaviors. Especially, 40 kHz calls were found on 'contact' and 'other' behaviors. We suggest that ultrasonic vocalizations need to be subdivided and the effects of individuals and behaviors must be considered to assess emotional state of rats because these may influence the features of ultrasonic vocalizations.

• 한국결정성장학회지
• /
• 제30권3호
• /
• pp.110-116
• /
• 2020

MLCC(Multi-Layer Ceramic Capacitor)의 유전체 층에 사용되는 BaTiO₃ 입자는 안정한 TCC(Temperature Characteristics of Capacitance) 거동을 갖기 위해 core/shell 구조를 갖는다. 지금까지 shell의 특성은 core/shell 구조의 전체 특성에서 유추해 왔다. 이는 core/shell 구조가 겨우 수 ㎛의 작은 크기로 shell 특성만 구별해서 측정하기가 어렵기 때문이다. 본 실험에서는 micro-contact법을 이용하여 확산쌍 시편의 계면에 형성된 확대된 core/shell 구조에 Pt 전극을 증착하여 35~135℃ 에서 shell 영역의 독립적인 TCC 거동을 측정하였다. 그 결과, 65℃에서 최대 유전율 값을 갖는 완만한 피크의 확산 상전이(Diffusion Phase Transition) 거동인 core의 특성과 구별되는 거동을 관찰하였으며, 이는 core/shell 구조의 온도-유전거동을 묘사하는 모델링에서 실험 자료로 활용될 것으로 본다.