• 대한소아치과학회지
• /
• 제50권4호
• /
• pp.396-408
• /
• 2023

이 연구의 목적은 유구치를 재현한 인공치를 대상으로 인접면 복합레진 수복 시 매트릭스 시스템에 따른 인접면의 외형, 접촉면의 크기 및 수복 전과 후의 부피 차이를 비교해 보는 것이다. 네 가지 종류의 인공치에 Circumferential 매트릭스 시스템에 해당하는 Tofflemire Matrix System과 Sectional 매트릭스 시스템에 해당하는 Palodent V3 Sectional Matrix System, myJunior Kit를 이용하여 복합레진을 수복하고 3D 모델링 과정을 거쳐 분석되었다. Sectional 매트릭스 시스템을 사용한 경우에서 오목한 인접면 외형이 형성될 확률이 높았으며 더 큰 접촉 면적과 부피가 형성되었다. 이는 Sectional 매트릭스 시스템에 사용되는 매트릭스 밴드의 완전 연질(Dead soft) 특성에 의한 변형으로 인해 접촉점 주변으로 과량의 레진이 적용될 수 있기 때문이다. 게다가 Sectional 매트릭스 시스템에 포함된 고무 웨지가 매트릭스 밴드를 와동에 잘 적합 시키지 못할 가능성이 있다. 따라서 이번 연구의 결과를 바탕으로 유구치 인접면을 Sectional 매트릭스 시스템을 이용해 복합레진 수복하는 경우, 형태학적 관점을 고려한 신중한 사용이 요구된다.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제34회 추계학술대회 개최
• /
• pp.19-26
• /
• 2001

The wear characteristic of Zircaloy-4 tube, which is used for a cladding of light water reactor fuel rod, is investigated experimentally. The experiment is conducted with contacting the crossed tube specimens in air as well as in water at room temperature with various combination of contact normal force and sliding distance of reciprocating motion. The contour and the volume of each wear are examined to study the effect of contact condition and environment on wear. As a result, it is found that the wear volume in the water environment is larger than that in the air for all the contact (i.e., force and sliding distance) conditions. However, the wear depth is greater in air than in water if the contact normal force and the sliding distance are larger. These are explained by the ease of detachment of wear particles from the contact surface. On the other hand, workrate model is applied with the contact shear force range measured by our wear tester. Investigated is the correlation between the workrate and the wear volume increase rate of the present experiment. The parabolic curve is found to fit well for the present wear data.

• Tribology and Lubricants
• /
• 제31권4호
• /
• pp.170-176
• /
• 2015

As a continuation of Part I, which developed a design formula of the minimum corner radius (R_min) for restraining tribological failures, Part II investigates design parameters such as material properties and contact force. As design examples, Al 7075-T651, SST 304 and HT-9 are chosen for the materials and 1, 10 and 100 kN are used for the forces. The results show that the difference in R_min decreases as either the elastic modulus increases or the contact force decreases. Given the same material and force, the permissible R_min decreases as the flat region increases and vice versa. Because the R_min values obtained from the examples are very small, the dimensions of the corner radius normally designed in engineering structures are regarded acceptable. The von Mises stress evaluated for a typical example, which is far below the yield strength, confirms this interpretation. Nevertheless, the present work can provide a design criterion as well as a guideline for quality control in the manufacturing of, in particular, contact corners, which has not been attempted before to the best of the author’s knowledge. In addition, this paper considers the problem of a step that may be formed in the contact contour by using a similar approach. The result shows that no size of the step is permissible.

• 한국군사과학기술학회지
• /
• 제11권5호
• /
• pp.107-115
• /
• 2008

In this paper, we have proposed a wear growth prediction method on the surface of rubber pad of track assembly installed in high-speed battle tank i.e. the automatic model updating code interfacing with commercial finite element simulation software. Also, simple and resonable geometrical, material finite element model was established to be easily updated based on the empirical threshold value of contact pressure on the contact surface. From the iterative model update and analysis results, we discovered a weak point on rubber pad surface and suggested a new design concept for improving the wear performance of track assembly.

• 대한기계학회논문집A
• /
• 제25권6호
• /
• pp.980-987
• /
• 2001

Tire performance is significantly influenced by the carcass tension distribution that is governed by the sidewall contour. To maximize the tire performance, it is very important for one to find the sidewall contour with the ideal tension distribution. But it is not easy to find such an optimal sidewall contour. Therefore, in order for a successful tire-shape optimization, we need to investigate how the change of sidewall radius influences on the carcass tension distribution. In this paper, we intend to numerically investigate the relation between the sidewall-radius change and the carcass tension distribution.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1272-1275
• /
• 2007

The HDD (hard disk drive) using Load/Unload (L/UL) technology includes the benefits which are increased areal density, reduced power consumption and improved shock resistance than those of contact-start-stop (CSS). Dynamic L/UL has been widely used in portable hard disk drive and will become the key technology for developing the small form factor hard disk drive. Main design objectives of the L/UL mechanisms are no slider-disk contact or no media damage even with contact during L/UL, and a smooth and short load and unload process. In this paper, we focus on state matrix, pitch static attitude (PSA), roll static attitude (RSA), loading/unloading contour (LC/ULC), impact force and contact. Stability of slider is mainly determined by PSA and RSA. State matrix by PSA and RSA is also important indicator. Therefore we analyze state matrix of SFF HDD suspension through the LC/ULC.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2001년도 제33회 춘계학술대회 개최
• /
• pp.81-88
• /
• 2001

To study the influence of the shape of contacting bodies (especially the end profile) on slip regime, wear test is conducted in the case of the contact between tube and support. Two different end profiles of the support are used such as truncated wedge and rounded punch. During the test, 10, 30 and 50 N are applied as normal force and slip displacement varies between 10-200 $\mu\textrm{m}$. The tube and the support specimens are made of Zircaloy-4 and a specially designed wear tester is used. Tests are carried out in air at room temperature. Wear on the tube is examined by measuring microscope. Partial and gross slip regimes are classified from the observed wear shape. Surface roughness tester is also used to measure the wear depth and contour, from which wear volume is evaluated. The transition from partial to gross slip is also investigated by investigating the considerable increase of wear volume. From the result, the boundary between the partial and the gross slip is newly determined in the conventional fretting map for the present specific contact configuration. Since the transition is related with the amount of energy dissipation from the contact surface so is wear, it is regarded that wear can be restrained by designing a proper shape of support.

• Structural Engineering and Mechanics
• /
• 제57권2호
• /
• pp.295-313
• /
• 2016

In this study, the three-dimensional finite element method is used to determine the stress intensity factor in Mode I and Mixed mode of a centered crack in an aluminum specimen repaired by a composite patch using contour integral. Various mesh densities were used to achieve convergence of the results. The effect of adhesive joint thickness, patch thickness, patch-specimen interface and layer sequence on the SIF was highlighted. The results obtained show that the patch-specimen contact surface is the best indicator of the deceleration of crack propagation, and hence of SIF reduction. Thus, the reduction in rigidity of the patch especially at adhesive layer-patch interface, allows the lowering of shear and normal stresses in the adhesive joint. The choice of the orientation of the adhesive layer-patch contact is important in the evolution of the shear and peel stresses. The patch will be more beneficial and effective while using the cross-layer on the contact surface.

• 공학교육연구
• /
• 제17권4호
• /
• pp.15-20
• /
• 2014

The non-contact easy detecting system of nursing person's body vital information and their behaviors monitoring system are developed, which consist of "Kinect" sensor and thermography camera. The "Kinect" sensor can catch the body contour and the body moving behavior, and output their imaging data realtime. The thermography camera can detect respiration state and body temperature, etc. In this study, the practicability of this system was verified.

• 한국기계가공학회지
• /
• 제8권2호
• /
• pp.40-45
• /
• 2009

This study is analyzed by stress contour of automotive tire at contact on road surface. Maximum equivalent stress as 61200Pa is shown on the lower mid part in case of tire contacted on road surface. As the air pressure of tire increases, maximum total deformation as 5mm is shown on the side part of tire. It can be shown that the side part of tire is unstabilized. There is no load effect on tire at its upper and lower directions. When the moment applied on the side of tire is increased 1.4 times as its value, the value of maximum principal stress is increased 1.4 times. The stress at the tire is in proportion to the moment applied on the its side. The tire tends to incline toward its side by this moment.