• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.04a
• /
• pp.263-267
• /
• 1995

The usual methods for the temperature control of mass-concrete structures include the use of low-heat cement, pre-cooling, post-cooling, or sheet curing. In order to control the heat of hydration during the construction of mass-concrete structures, the combination of the above methods is commonly employed. For the construction of mass-concrete structures such as massive pier or anchor, it is necessary to control the curing temperature with pipe cooling. In this study, the method of analysis on the effect of pipe of was proposed to prevent the thermal cracking due to heat of hydration In addition the effect of covering the concrete surface with blanket insulation was investigated. The results of the present study may be useful for the prediction of curing temperature of mass-concrete structures and the reasonable construction management.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2003.05a
• /
• pp.7-11
• /
• 2003

This study investigate the hydration heat history with variation of surface insulating material in cold weather concreting. According to the results, the temperature of concrete lowers below zero in 24hours, so early frost damage occurs in the case of exposure and 1 fold bubble sheet, but the lowest temperature keeps above zero, so a adiabatic effect is very favorable in the case of double bubble sheet and 부직포. Compressive strength of core specimen at 7 and 28 days is highest In the case of double bubble sheet and 부직포. But, considering convenience of construction and economical efficiency, it is thought that the most effective surface insulating material is 1 fold bubble sheet +blanket.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05a
• /
• pp.491-494
• /
• 2005

This study was carried out to examine application of surface adiabatic curing method in slightly cold weathering period. So, early aged freezing damage and compressive strength of concrete were examined through temperature analysis of construction concrete. Temperature analysis was carried out according to the average temperature, concrete placement completion time and surface adiabatic curing method. Analysis results show that additional curing plans are demanded in concrete construction below 0$^{circ}C$, surface adiabatic curing method is could apply in the average temperature more than -2$^{circ}C$ and curing method as heating are needed under -2$^{circ}C$.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.9-10
• /
• 2017

For the structural analysis of reinforced concrete structures, the mechanical properties of concrete at each temperature are required and the mechanical property values according to specific temperature are presented in the design regulations and codes. In this study, the mechanical properties of concrete were experimented by using 35MPa concrete produced in Korea from 20℃ to 900℃(two kinds of test method). Compared the results with previous domestic papers, we aimed to contribute to the construction of mechanical characteristics D.B. of at the elevated temperatures of domestically produced concrete which can be used for structural analysis in fire.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.11a
• /
• pp.179-180
• /
• 2015

In this study, the experimental study on Insulation performance of insulated forms utilizing NT frame heat insulation at low Temperature. For this study, placing insulated TEGO film plywood based form between two constant temperature and humidity chamber that maintaining 10℃, decrease temperature of one chamber to -10℃ and -20℃. Each of steps, maintaining period of temperature was 1 hour. After placing the insulated form, measure temperature of outside if insulated form. As a result of experiment, temperature difference of Fumed Silica Vacuum insulation was lowest.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2018.05a
• /
• pp.58-59
• /
• 2018

In this study, firing experiments were carried out to confirm the foamability of the expansive shale collected from the local area. When expansive shales are subjected to high temperature heat, gas is generated inside and voids are formed. Due to this phenomenon, shale is used as a raw material for lightweight aggregate. Experiments were carried out with different plastic temperature and residence time to find the appropriate plastic temperature for this expansive shale. As a result, the higher the plastic temperature, the more the surface viscosity increased and the gas generated inside were retained. Resulting in a number of internal voids. However, even if the plastic temperature or the medium temperature is high, it is confirmed that sufficient gas is not generated when the residence time is shortened.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2015.05a
• /
• pp.57-58
• /
• 2015

In this study, the experimental study on Thermal Performance of Insulated Forms with Different Insulating Methods at Low Temperature. For this study, placing insulated plywood based form between two constant temperature chamber that maintaining 10℃, decrease temperature of one chamber to -10℃ and -20℃. Each of steps, maintaining period of temperature was 1 hour. After placing the form, measure temperature of opposite side of the insulated form. As a result of experiment, temperature difference of rigid urethane was lowest.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1437-1443
• /
• 2010

Thermal stresses due to the heat of hydration can cause extensive cracking in subway structures. In order to reduce heat cracks, construction methods (e.g. sequential or skipping construction methods) need to be changed. However, to our knowledge, the existing literature contains little information on the correlation between heat cracks and construction methods. Thus, in this study, the temperature crack index table was suggested based on construction lengths (6 m, 9 m and 18 m), concrete mixtures (Type I cement with FA of 20 % in cement weight, Type IV cement with FA of 10 % in cement weight, and mixture of three different cements), construction seasons (spring or autumn, summer and winter) and construction method (sequential or skipping construction methods). The index table can be easily used corresponding to changes in concrete placing method at the construction site. Also, the correlation of cracking due to sequential or skipping construction methods was derived based on the statistical approaches.

• International Journal of High-Rise Buildings
• /
• v.4 no.4
• /
• pp.283-290
• /
• 2015

Crack control remains a primary concern for mass concrete structures, where the majority of cracking is caused by temperature changes during the hydration process. One-time pouring is a useful construction method for mass concrete structures. The suitability of this method for constructingon of the Shanghai Tower's mass concrete foundation slab of Shanghai Tower is considered here by a numerical simulation method based on a 6- meter- thick slab. Some of the conclusions, which can be verified by monitoring results conducted during construction, are as follows. The temperature gradient is greater in the vertical direction than in the radial direction, therefore, the vertical temperature gradient should be carefully considered for the purpose of crack control. Moreover, owing to cooling conditions at the surfaces and the cement mortar content of the slab, the temperatures and temperature gradients with respect to time vary according to the position within the slab.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2011.11a
• /
• pp.237-239
• /
• 2011

This study was performed to investigate the influence of curing temperature on the properties of light weight foamed concrete, manufactured on-site construction according to the various experimental factor such as temperature of material, curing temperature in air(5, 10, 20℃), curing time in air(5, 10, 15hour), and target density of hardened state(0.8, 1.2t/㎥). As a result, the influence of the curing temperature on various properties of foamed concrete is greater than curing time. When increasing temperature and time in air curing, progress of hydration is fast and compressive strength is increasing more and more. However, when considering the productivity, minimum curing time is required 15hours at 5℃, 10hours at 10℃, and 5hours at 20℃. If this condition is not required, there is some crack due to volume expansion on the surface of light weight foamed concrete.