• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.05a
• /
• pp.586-587
• /
• 2010

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.2
• /
• pp.102-107
• /
• 2014

The engine excitation forces are considered as major vibration source for the forklift truck, especially in small class. Even though the current engine mounting system designs are acceptable for vibration isolation, the performance of the engine mounting system is still required for the tendency of light weight, higher power and driver's higher vibration requirement. In this paper vibration reduction technique of forklift engine which is supported on rubber mounts is presented. Based on the dynamic model of resilient engine mounting system, design evaluation program is established. The design optimization technique and evaluation method of system properties are discussed. Effects of optimal design are validated through comparison with test results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2001.05a
• /
• pp.635-641
• /
• 2001

This study introduces the basic concepts of the vibration reducing methods and presents a case study of 'A' apartment construction site which located nearby railroad. The site is only 60m away from the railroad. Therefor much noise and vibration damages could be expected during train or any other transportation's passing. Especially, the first and second floor may suffer much vibration with the low frequency radiation noise from the walls and floors. This study estimates the noise level of indoor area by measuring the vibration of indoor walls and floors. From this result, vibration barrier, as a method to reduce the noise level which exceeds proper standard value, was attempted to protect vibration transmit from the railroad.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.8
• /
• pp.553-558
• /
• 2015

This paper aims at making a dedicated vibration monitoring and diagnosis framework for 3MW WTG(wind turbine generator). Within the scope of the research, vibration data of WTG drive train are used and WTG operating conditions are involved for dividing the vibration data class which included transient and steady state vibration signals. We separate two health detections which are CHD(continuous health detection) and EHD(event health detection). CHD has function of early detection and continuous monitoring. EHD makes the use of finding vibration values of fault components effectively by spectrum matrix subsystem. We proposed framework and showed application for 3MW WTG in a practical point of view.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.868-869
• /
• 2013

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.05a
• /
• pp.292-295
• /
• 2006

Dimension and capacity of the zero tail type mini excavator are small as compared with medium or large excavators. Therefore, problems of the noise and the heat are major issues in design due to layout of each component such as the engine and the hydraulic module. It is necessary to reduce the noise and the vibration of construction machine, due to be enforced regulation for high noise construction machinery in the world. The objective of this study is to provide basic data which is apply to predict noise effect in detail design stage by estimating noise of cabin for zero tail type mini excavator.

• Land and Housing Review
• /
• v.5 no.3
• /
• pp.169-177
• /
• 2014

Constructing urban public housing built adjacent railway site has the noise and vibration problem coming from operation of trains. Thus, anti-vibration plans utilizing anti-vibration pads must be established to minimize the impact of train noise and vibration from the tunnels on the residents of the public housing. Under various difficulties and expectation from the citizens, many efforts were taken to satisfy the amenity requirements on noise and vibration for the residential area. As a results, it can be recognized that amenity standards can be satisfied. But great caution is required to prepare ourselves for various situations that might occur during construction, especially considering that the relevant railroads are still under operation.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.535-540
• /
• 2005

In environmental impact assessment, noise impact assessment usually consists of three stages surveying the existing noise levels by measurements, predicting noise levels induced by construction works and predicting noise levels after the completion of project. When predicting noise level in urban area, this method does not consider acoustic phenomena like multi reflection, diffraction and absorption due to complex topographic configuration of building and terrains. For the purpose, a noise mapping tool is utilized to produce a series of noise maps, which are those for the present, for the works of construction and for the future. For accurate noise mapping, acoustical and topographic information is essential. Standard sound power levels and directivities of various construction equipments are required and scheduling of construction processes and locations of the equipments should be provided. In the case of exceeding legal limit, mitigation measures are applied to satisfy the legal limits and subsequent noise map is obtained and checked.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.11 s.104
• /
• pp.1311-1317
• /
• 2005

In environmental Impact assessment, noise impact assessment usually consists of three stages-surveying the existing noise levels by measurements, predicting noise levels induced by construction works and predicting noise levels after the completion of a project. The distance-attenuation relation of a point source, which has been used to predict the noise level due to its simplicity does not consider complex acoustic phenomena like multi-reflection, -diffraction and -absorption due to complex topographic configuration of buildings and terrains. For the consideration of such physical complexities. a noise mapping tool is adopted to produce a series of noise maps, which are those for the present, tot the works of construction and for the future. For accurate noise mapping, acoustical and topographic Information is used. Standard sound power levels and directivities of various construction equipments are need and scheduling of construction processes and locations of the equipments should be provided. In the case of exceeding legal limit, mitigation measures are applied to satisfy the legal limits and subsequent noise map is obtained and checked.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.05a
• /
• pp.65-66
• /
• 2021

Due to the inexperience of stone work and field workmanship, and the preference of simple construction, various problems such as unauthorized cutting of the touch and epoxy bonding are occurring. Therefore, the existing T-type hole construction method was developed to fundamentally control these attempts. As a result of comparison with the control panel method, vibration and noise were reduced by 2dB and 10dB, indicating an excellent effect. Particularly, dust was about 1/102~1/61 in individual values, and the average value was 1/80 (12.5%). The effect of preventing damage and environmental pollution is expected to be great.