• Journal of Mechanical Science and Technology
• /
• 제17권1호
• /
• pp.23-31
• /
• 2003

This paper introduces a constraint operator for the kinematic calibration of a parallel mechanism. By adopting the concept of a constraint operator, the movement between two poses is constrained. When the constrained movements are satisfied, the active joint displacements are taken and inputted into the kinematic model to compute the theoretical movements. A cost function is derived by the errors between the theoretical movement and the actual movement. The parameters that minimize the cost function are estimated and substituted into the kinematic model for a kinematic calibration. A single constraint plane is employed as a mechanical fixture to constrain the movement, and three digital indicators are used as the sensing devices to determine whether the constrained movement is satisfied. This calibration system represents an effective, low cost and feasible technique for a parallel mechanism. A calibration algorithm is developed with a constraint operator and implemented on a parallel manipulator constructed for a machining center tool.

• 대한기계학회논문집A
• /
• 제27권4호
• /
• pp.647-655
• /
• 2003

This paper studies the observability of calibration system with a constraint movement by a constraint operator. The calibration system with the constraint movement need only simple sensing device to check whether the constraint movements are completed within an established range. However, it yields the concern about the poor parameter observability due to the constraint movements. This paper uses the QR-decomposition to find the optimal calibration configurations maximizing the linear independence of rows of a observation matrix. The number of identifiable parameters are examined by the rank of the observation matrix, which represents the parameter observability. The method is applied to a parallel typed machining center and the calibration results are presented. These results verify that the calibration system with low-cost indicators and simple planar table is accurate as well as reliable.

• 대한전기학회논문지:전력기술부문A
• /
• 제53권8호
• /
• pp.484-489
• /
• 2004

When the energy resource available to a particular plant (be it coal, oil, gas, water, or nuclear fuel) is a limiting factor in the operation of the plant, the entire economic dispatch calculation must be done differently. Each economic dispatch calculation must account for what happened before and what will happen in the future. This paper presents a formulation and a solution method for the optimization problem with a fuel constraint in a competitive electricity market. Take-or- Pay (TOP) contract for an energy resource is the typical constraint as a limiting factor. Two approaches are proposed in this paper for modeling the dispatch calculation in a market mechanism. The approaches differ in the subject who considers and inserts the fuel-constraint into its optimization problem. Market operator and each power producer having a TOP contract are assumed as such subjects. The two approaches are compared from the viewpoint of profits. surplus. and social welfare on the basis of Nash Equilibrium.

• 대한수학회보
• /
• 제23권2호
• /
• pp.141-148
• /
• 1986

In [1], M. Guignard considered a constraint set in a Banach space, which is similar to that in [2] and gave a first order necessary optimality condition which generalized the Kuhn-Tucker conditions [3]. Sufficiency is proved for objective functions which is either pseudoconcave [5] or quasi-concave [6] where the constraint sets are taken pseudoconvex. In this note, we consider a psedoconvex programming problem in a Hilbert space. Constraint set in a Hillbert space being pseudoconvex and the objective function is restrained by an operator equation. Then we use the methods similar to that in [1] and [6] to obtain a necessary and sufficient optimality condition.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국내학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.191-196
• /
• 1991

LQG/LTR method have a theoretical constraint that it cannot applied to nonminimum phase plant. In this paper, we suggest two methods of approximation of minimum phase plant for a given nonminimum phase plant to solve this constraint. Error is described by additive form which can reduce its magnitude in broad frequency range. A optimal approximation method was suggesetd by using Hankel operator theory and Nehari theory. It is showen by example that the methods suggested can resolve the frequency domain constraint arised in Stein and Athans approximation.

• 한국통신학회논문지
• /
• 제16권10호
• /
• pp.972-980
• /
• 1991

LQG/LTR method have a theoretical constraint that it cannot applied to nonminimum phase plant. In this paper we suggest two methods of approximation of minimum phase plant for a given nonminimum phase plant to solve this constraint. Error is described by additive form which can reduce its magnitude in broad frequency range. A optimal approximation method was suggested by using Hankel operator theory and Nehan theory it is shown by example that the methods suggested can resolve the frequency domain constraint arised in Stein and Athans approximation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 A
• /
• pp.716-718
• /
• 2004

This paper presents a formulation and a solution method for the optimization problem with a fuel constraint in a competitive electricity market. Take-or-Pay (TOP) contract for an energy resource is the typical constraint as a limiting factor. Two approaches are proposed in this paper for modeling the dispatch calculation in a market mechanism. The approaches differ in the subject who considers and inserts the fuel-constraint into its optimization problem. Market operator and each power producer having a TOP contract are assumed as such subjects.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.321-322
• /
• 2007

• 대한기계학회논문집A
• /
• 제26권11호
• /
• pp.2237-2244
• /
• 2002

This research develops a low-cost and high accuracy kinematic calibration method based on the following principles: 1) the platform locations are accurately measured by a constrained movement to inspect a calibration target; 2) the constrained movement is chosen to guarantee the parameter observability; 3) the mechanical fixture to constrain the movement and the sensor to check the constrained movement are implemented by low-cost and high-accuracy devices; 4) the calibration is easily done at an industrial environment. The kinematic parameters calibrated with respect to a single plane aren't influenced due to the misalignment of the plane. A parameter observability is successfully obtained even through one planar constraint, which guarantees that all kinematic parameters are estimated by minimizing the cost function.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.521-526
• /
• 2001

This research develops a low-cost and high accurate kinematic calibration method for a parallel typed machining center tool. A planar table is used for a mechanical fixture restricting the platform to place at the constrained pose and a low-cost and high accurate digital indicator is employed for a device checking if the constrained movement is satisfied within the established range. The kinematic parameters calibrated with respect to a single plane aren't influenced from the misalignment of the plane. A parameter observability is successfully obtained even through one planar constraint, which guarantees that the kinematic parameters is estimated by minimizing the cost function.