• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.44 no.8
• /
• pp.1068-1074
• /
• 1995

Effect of (Zn$_{1}$3/Nb$_{2}$3/) $O_{2}$ addition on the phase changes and microwave dielectric properties of BaTi $O_{3}$-3Ti $O_{2}$ ceramics were investigated. Addition of (Zn$_{1}$3/Nb$_{2}$3/) $O_{2}$ to BaTi $O_{3}$-3Ti $O_{2}$ resulted in the formation of Ba $Ti_{4}$$O_{9}$, $Ba_{2}$ $Ti_{9}$ $O_{20}$, Ba(Zn$_{1}$3/Nb$_{2}$3/) $O_{3}$, and Ti $O_{2}$ phases. Ba $Ti_{4}$$O_{9}$ phase was gradually transformed to $Ba_{2}$ $Ti_{9}$ $O_{20}$. This was identified by XRD and microstructure. As the Ba $Ti_{4}$$O_{9}$ phase transformed to $Ba_{2}$ $Ti_{9}$ $O_{20}$ phase, the dielectric constant increased to 37.5. Q*f$_{o}$ value was 40000 at x=0.04, and the temperature coefficient of resonant frequency was +10ppm/.deg. C.C.. C.C.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.2
• /
• pp.67-72
• /
• 2004

The microwave dielectric properties and microstructure of the (1-x)$Mg_4Ta_2O_{9-x}TiO_2$(X=0, 0.3, 0.4) ceramic were, investigated. The specimens were prepared by the conventional mixed oxide method with sintering temperature of $1350^{\circ}C$∼$1425^{\circ}C$. According to the XRD patterns, the (1-x)$Mg_4Ta_2O_{9-x}TiO_2$(X=0, 0.3, 0.4) ceramics have the $Mg_4Ta_2O_{9}$ phase(hexagonal). The dielectric constant($\varepsilon$$_{\gamma}$) and density increased with sintering temperature and mole fraction of x. To improve the quality factor and the temperature coefficient of resonant frequency, TiO$_2$($\varepsilon_{r}$=100, $Q{\times}f_{r}$=40,000GHz, $\tau$$_{f}$=＋450 ppm/$^{\circ}C$) was added in $Mg_4Ta_2O_{9}$ ceramics. In the case of the $0.7Mg_4Ta_2O_{9}$-$0.3TiO_2$ and the $0.6Mg_4Ta_2O_{9}$-$0.4TiO_2$ceramics sintered at $1400^{\circ}C$ for 5hr., the microwave dielectric properties were $\varepsilon$$_{\gamma}$=11.72, $Q{\times}f_{r}$=126,419GHz, $\tau_{f}$=-31.82 ppm/$^{\circ}C$ and $\varepsilon_{r}$=12.19, $Q{\times}f_{r}$=109,411GHZ, $\tau$$_{f}$= -17.21 ppm/$^{\circ}C$, respectively.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2410-2412
• /
• 2005

In this study, two types of PS substrate were fabricated for sensing of chemical and biological substances. For sensing of the humidity and chemical analyzes such as $CH_3OH$ or $C_2H_5OH$, PS layers are prepared by photoelectrochemical etching of silicon wafer in aqueous hydrofluoric acid solution. To evaluate their sensitivity, we measured the resistance variation of the PS diaphragm. As the amplitude of applied voltage increases from 2 to 6Vpp at constant frequency of 5kHz, the resistance variation for humidity sensor rises from 376.3 to $784.8{\Omega}$/%RH. And the sensitivities for $CH_3OH$ and $C_2H_5OH$ were 0.068 uA/% and 0.212 uA/%, respectively. For biological sensing application, amperometric urea sensors were fabricated based on porous silicon(PS), and planar silicon(PLS) electrode substrates by the electrochemical methods. Pt thin film was sputtered on these substrates which were previously formed by electrochemical anodization. Poly (3-methylthiophene) (P3MT) were used for electron transfer matrix between urease(Urs) and the electrode phase, and Urs also was by electrochemically immobilized. Effective working area of these electrodes was determined for the first time by using $Fe(CN)_6^{3-}/Fe(CN)_6^{4-}$ redox couple in which nearly reversible cyclic voltammograms were obtained. The $i_p$ vs $v^{1/2}$ plots show that effective working electrode area of the PS-based Pt thin film electrode was 1.6 times larger than the PLS-based one and we can readily expect the enlarged surface area of PS electrode would result in increased sensitivity by ca. 1.6 times. Actually, amperometric sensitivity of the Urs/P3MT/Pt/PS electrode was ca 0.91uA/$mM{\cdot}cm^2$, and that of the Urs/P3MT/Pt/PLS electrode was ca. 0.91uA/$mM{\cdot}cm^2$ in a linear range of 1mmol/L to 100mmol/L urea concentrations

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.212-214
• /
• 2004

In this study, we fabricated the organic thin film by self-assembly method by using nitro-group and methoxy-group organic molecule. Also, we selected the organic single molecule in organic thin film and measured current-voltage characteristics by using scanning tunneling microscopy. The Organic molecules that use in an experiment is 4,4'-(diethynylphenyl)-2'-nitro-1-benzen ethiol and 4-[2,5-dimethoxy-4-ph enylethynylphenyl]ethynylphenylethanthiol. 4,4'-(dimet hynylphenyl)-2'-nitro-1-benzenethiol is applied widely in molecular electronic device and 4-[2,5-dime thoxy-4-phenylethynylphenyl]ethynylphenylethanthiol composed in Korea Research Institute of Chemical Technology. To be confirmed the formation of the self-assembled monolayers, we observed the real time frequency shift of the QCM and investigated surface of the self-assembled monolayers the using STM. With this, we measured current to the organic single molecule, in condition of the air state. As a result, we confirmed in constant voltage that properties of negative differential resistance. Using properties of negative differential resistance to get from this study, application is expected to be molecular switching device, memory device and logic device.

• Journal of Sensor Science and Technology
• /
• v.7 no.4
• /
• pp.234-242
• /
• 1998

Changes in transmission and thermoluminescent characteristics were used in order to find out the optimum growth condition of CsI single crystal scintillators which were made relatively defect-free using Czochralski method. Impurity distribution in the crystals and the intensity and number of thermoluminescent glow peaks decreased as the process of crystallization was repeated. The direction of crystal growth turned out to be (110), the crystal structure of grown CsI was bee, and its lattice constant was found to be $4.568{\AA}$. The activation energy (trap depths) of CsI:3rd was 0.45 eV and its frequency factor was $5.18{\times}10^5\;sec^{-1}$.

• The Korean Journal of Physiology and Pharmacology
• /
• v.10 no.2
• /
• pp.71-77
• /
• 2006

The goal of this study was to analyze the effects of genistein, a widely used tyrosine kinase inhibitor, on cloned Shaw-type $K^+$ currents, Kv3.1 which were stably expressed in Chinese hamster ovary (CHO) cells, using the whole-cell configuration of patch-clamp techniques. In whole-cell recordings, genistein at external concentrations from 10 to $100{\mu}M$ accelerated the rate of inactivation of Kv3.1 currents, thereby concentration-dependently reducing the current at the end of depolarizing pulse with an $IC_{50}$ value of $15.71{\pm}0.67{\mu}M$ and a Hill coefficient of $3.28{\pm}0.35$ (n=5). The time constant of activation at a 300 ms depolarizing test pulses from -80 mV to +40 mV was $1.01{\pm}0.04$ ms and $0.90{\pm}0.05$ ms (n=9) under control conditions and in the presence of $20{\mu}M$ genistein, respectively, indicating that the activation kinetics was not significantly modified by genistein. Genistein $(20{\mu}M)$ slowed the deactivation of the tail current elicited upon repolarization to -40 mV, thus inducing a crossover phenomenon. These results suggest that drug unbinding is required before Kv3.1 channels can close. Genistein-induced block was voltage-dependent, increasing in the voltage range $(-20\'mV{\sim}0\'mV)$ for channel opening, suggesting an open channel interaction. Genistein $(20{\mu}M)$ produced use-dependent block of Kv3.1 at a stimulation frequency of 1 Hz. The voltage dependence of steady-state inactivation of Kv3.1 was not changed by $20{\mu}M$ genistein. Our results indicate that genistein blocks directly Kv3.1 currents in concentration-, voltage-, time-dependent manners and the action of genistein on Kv3.1 is independent of tyrosine kinase inhibition.

• Journal of Satellite, Information and Communications
• /
• v.12 no.2
• /
• pp.89-93
• /
• 2017

This paper introduces an energy harvesting system that generates energy by collecting multi-band RF signals using buck-boost DC-DC converter. In an environment where the resistance of load using the collected electric energy is constantly changing, a buck-boost DC-DC converter is used in which the input resistance of the DC-DC converter does not change even if the load resistance changes. Since the frequency band of the input RF signal varies, the rectifier is designed for each band so that multiple bands can be processed, and a matching circuit is added to each band in front of the rectifier. For a rectifier to collect very small RF signals, a circuit is designed so that a constant voltage is obtained according to a very small input signal by devising a method of continuously accumulating the voltages collected and generated in each band. It is confirmed that the output efficiency can reach up to 20% even for the RF signal having the input of -20 dBm.

• International Journal of Automotive Technology
• /
• v.6 no.2
• /
• pp.149-159
• /
• 2005

A full nonlinear finite element P185/70Rl4 passenger car radial-ply tire model was developed and run on a 1.7-meter-diameter spinning test drum/cleat model at a constant speed of 50 km/h in order to investigate the tire transient response characteristics, i.e. the tire in-plane free vibration modes transmissibility. The virtual tire/drum finite element model was constructed and tested using the nonlinear finite element analysis software, PAM-SHOCK, a nonlinear finite element analysis code. The tire model was constructed in extreme detail with three-dimensional solid, layered membrane, and beam finite elements, incorporating over 18,000 nodes and 24 different types of materials. The reaction forces of the tire axle in vertical (Z axis) and longitudinal (X axis) directions were recorded when the tire rolled over a cleat on the drum, and then the FFT algorithm was applied to examine the transient response information in the frequency domain. The result showed that this PI 85/70Rl4 tire has clear peaks of 84 and 45 Hz transmissibility in the vertical and longitudinal directions. This result was validated against more than 10 previous studies by either theoretical or experimental approaches and showed excellent agreement. The tire's post-impact response was also investigated to verify the numerical convergence and computational stability of this FEA tire model and simulation strategy, the extraordinarily stable scenario was confirmed. The tire in-plane free vibration modes transmissibility was successfully detected. This approach was never before attempted in investigations of tire in-plane free vibration modes transmission phenomena; this work is believed to be the first of its kind.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.5
• /
• pp.269-274
• /
• 2016

This paper proposes the development of a low frequency electronic hammer drive system that is used to prevent scaling or clogging in the hopper process. The electro-mechanical hammering driving method involves the generation of vibration and impact energy. The operation principles of the electromagnetic hammer were considered by parallel/series spring coefficient analysis and the amount of kinetic energy generated was calculated from the product of the equivalent spring constant, which is coupled with the E core and the gap of between the E core and I core. In addition, the Pulsation Driving algorithm was applied to the proposed electromagnetic hammer to obtain the maximizing kinetic energy. This algorithm was then implemented by a logical AND operation process and micro-controller (atmega128) built in functions with a timer interrupt and PWM generation function. The driving circuit of the electromagnetic hammer was designed using the H-bridge type IGBT circuit. The experimental test was performed by usefulness of the developed electromagnetic hammer systems with the acceleration measurement method. The experimental result showed that the proposed system has good kinetic energy generation performance and can be applied to the hopper process.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.7 no.5
• /
• pp.866-874
• /
• 2006

This paper proposes a new Dynamic Voltage Scaling(DVS) algorithm to achieve low-power scheduling of aperiodic hard real-time tasks. Aperiodic tasks schedulingcannot be applied to the conventional DVS algorithm and result in consuming energy more than periodic tasks because they have no period, non predictable worst case execution time, and release time. In this paper, we defined Virtual Periodic Task Set(VTS) which has constant period and worst case execution time, and released aperiodic tasks are assigned to this VTS. The period and worst case execution time of the virtual task can be obtained by calculating task utilization rate of both periodic and aperiodic tasks. The proposed DVS algorithm scales the frequency of both periodic and aperiodic tasks in VTS. Simulation results show that the energy consumption of the proposed algorithm is reduced by 11% over the conventional DVS algorithm for only periodic task.