• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.386-389
• /
• 2001

In this study, development of a new LTCC material using non-glassy system was attempted with respect to reducing the fabrication process steps and cost down. Lowering the sintering temperature can be achieved by liquid phase sintering. However, presence of liquid phases usually decrease dielectric properties, especially the quality factor. Therefore, the starting material must have quality factor as high as possible in microwave frequency range. And also, the material should have a low dielectric constant for enhancing the signal propagation speed. Regarding these factors, dielectric constants of various materials were estimated by the Clausius-Mosotti equation. Among them, ZnWO$_4$ was turned out the suitable LTCC material. ZnWO$_4$ can be sintered up to 98% of full density at 105$0^{\circ}C$ for 3 hours. It's measured dielectric constant, quality factor, and temperature coefficient of resonant frequency were 15.5, 74380GHz, and -70ppm/$^{\circ}C$, respectively In order to modify the dielectric properties and densification temperature, B$_2$O$_3$ and V$_2$O$_{5}$ were added to ZnWO$_4$. 40 mol% B$_2$O$_3$ addition reduced the dielectric constant from 15.5 to 12. And the temperature coefficient of resonant frequency was improved from -70 to -7.6ppm/$^{\circ}C$. However, sintering temperature did not change due to either lack of liquid phase or high viscosity of liquid phase. Incorporation of small amount of V$_2$O$_{5}$ in ZnWO$_4$-B$_2$O$_3$ system enhanced liquid phase sintering. 0.lwt% V$_2$O$_{5}$ addition to the 0.6ZnWO$_4$-0.4B$_2$O$_3$ system, reduced the sintering temperature down to 95$0^{\circ}C$ Dielectric constant, quality factor, and temperature coefficient of resonant frequency were 9.5, 16737GHz, and -21.6ppm/$^{\circ}C$ respectively.ively.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권10호
• /
• pp.505-509
• /
• 2004

The (Sr/sub 0.9/Ca/sub 0.1/)TiO₃(SCT) thin films are deposited on Pt-coated electrode(Pt/TiN/SiO₂/Si) using RF sputtering method at various substrate temperature. The optimum conditions of RF power and Ar/O₂ ratio were 140[W] and 80/20, respectively. Deposition rate of SCT thin film was about 18.75[Å/min]. The crystallinity of SCT thin films were increased with increase of substrate temperature in the temperature range of 100～500[℃]. The dielectric constant of SCT thin films were increased with the increase of substrate temperature, and changed almost linearly in temperature ranges of -80～+90[℃]. The current-voltage characteristics of SCT thin films showed the increasing leakage current as the substrate temperature increases.

• 한국식품영양과학회지
• /
• 제10권1호
• /
• pp.53-60
• /
• 1981

열풍에 의한 표고버섯의 건조현상을 속도론적으로 규명하기 위해서 건조속도를 좌우하는 두 가지 인자에 대해서 그 영향을 고찰한 후 선정된 조건에서 건조곡선 및 건조속도식을 유도하였다. 일정 풍속(1.5m/sec)하에서 온도의 변화$(45{\sim}55^{\circ}C)$를 주었을 때 수분의 감소는 지수함수적으로 감소하였으며 감소율은 온도가 높을수록 더욱 높았다. 온도를 $(45^{\circ}C)$로 고정시키고 풍속의 변화$(1.0{\sim}3.1m/sec)$를 주었을 때 2m/sec까지는 풍속이 빠를수록 건조속도가 높아졌으나, 그 이상의 풍속에서는 오히려 건조속도가 감소하였다. 따라서 풍속은 2m/sec에서 가장 건조속도가 높았다. 선정된 온도 $50^{\circ}C$, 풍속 2m/sec, 습도 38-41%의 조건에서 건조곡선 및 건조속도식을 유도하여 본 결과 $X=6.94e^{-0.345t}$와, $dx/dt=-2.39e^{-0.345t}$라는 Kinetic model 이 얻어졌다.

• 한국세라믹학회지
• /
• 제31권2호
• /
• pp.171-176
• /
• 1994

The spin-casted PLZT(9/65/35) thin films through polymeric sol-gel process were prepared on Pt substrate. The crack-free, uniform and dense films were obtained by post-annealing at the temperature between 35$0^{\circ}C$ and $700^{\circ}C$. The composite structure mixed together with large grains called "rosette" and surrounding small grains were observed on the films annealed over $600^{\circ}C$. Pyrochlore phase was completely changed to perovskite phase above $600^{\circ}C$ with the increase of annealing temperature. Dielectric constant (k) was larger with the increase of film thickness and annealing temperature. from the measurements of dielectric constant as a function of measuring temperature, it was also observed that Curie temperature was shifted to higher temperature with the increase of film thickness and annealing temperature. The pyroelectric coefficient(P) of 10 times coated film annealed at $700^{\circ}C$ was 65 $\mu$C/$\textrm{cm}^2$.K.$.K.

• 한국주조공학회지
• /
• 제8권4호
• /
• pp.429-436
• /
• 1988

The influences of some casting conditions on bonding ratio and state at bonding zone of stainless steel-cast iron dual tube produced by centrifugal casting process were investigated to estimate fabrication technics. 1) Bonding ratio is increasing such as increasing of inner surface temperature of outer metal(stainless steel STS 304), if pouring temperature of inner metal (cast iron) is constant. 2) The more pouring temperature of inner metal (cast iron) increase, the more bonding ratio increase when inner surface temperature of outer metal (cast iron) is constant. 3) As the mold rotary speed is increase, the hatching area of bonding map (perfect bonding area) goes down to the low pouring temperature of inner metal. 4) In order to predict bonding state of two different metal, we are able to make and use the bonding map about casting conditions such as inner surface temperature of outer metal, pouring temperature of inner metal and mold rotary speed.

• 지질공학
• /
• 제28권4호
• /
• pp.715-726
• /
• 2018

제체의 누수를 탐지하는 방법으로서 물리탐사, 온도 계측, 광섬유 등 다양한 방법이 개발되어 왔다. 본 연구에서는 FDR 센서의 유전율상수를 이용한 누수 탐지의 가능성을 파악하기 위하여 취약부와 미취약부로 구성된 물리모형을 제작하였으며 유전율상수, 온도 및 간극수압 센서를 설치하였다. 누수가 형성됨에 따라 유전율상수는 미취약부보다 취약부에서 빠르게 변화되었다. 또한, 취약부에서 간극수압, 온도 및 유전율 상수를 비교하면 유전율 상수의 반응이 가장 빠르고 하류 계측 지점에서도 쉽게 인지되는 특성을 보였다. 이와 같은 특성을 고려할 때, 제체 하류 구간에서 분포형으로 유전율을 측정한다면 누수 탐지에 빠르고 효율적으로 대처할 수 있을 것으로 파악되었다.

• 한국산학기술학회논문지
• /
• 제18권1호
• /
• pp.345-350
• /
• 2017

디젤 엔진의 연비와 배기를 개선하고자 하는 노력으로 다운사이징이 강화되고 있다. 이에 따라 엔진의 사이즈는 작아지고, 엔진 연소실 내 온도와 압력은 상승하는 추세이다. 따라서 높은 온도와 압력 조건에서 연료 분무의 발달과정과 연소과정 연구가 매우 중요하다. 본 연구에서는 디젤 엔진 연소실의 고온 고압 환경을 벤치에서 모사해줄 수 있는 정적 연소실을 개발하였다. 정적 연소실은 예혼합기를 연소시켜 순간적으로 온도와 압력을 급격하게 상승시킨 다음, 주변으로의 열전달에 의해 온도와 압력이 감소할 때 시험 목표조건인 온도와 압력 조건에 다다르면, 연료 분사기에 신호를 인가하여 연료분무를 개시하며 쿼츠 창을 통하여 연료 분무를 가시화 한다. 이 때, 정적 연소실 내에 연료 분무가 이루어지는 영역의 온도를 정확히 측정하여 정확한 시험 조건을 형성해야 한다. 본 연구에서는 고속으로 온도를 측정할 수 있는 열전대를 직접 개발 및 제작하여 연소실 내 시공간적 온도분포를 측정하였다. 측정 결과, 전체 체적 온도보다 연료 분무가 개시되는 중심 공간의 온도가 더 높게 나타났으며, 이는 연소실 벽면으로의 열전달 때문임을 확인하였다. 또한 횡방향으로의 온도 편차는 약 10%이내 수준이었으나, 종방향으로 온도편차가 최대 15%수준으로 나타났고 이는 부력으로 인한 고온의 연소가스의 상승효과 때문으로 판단되었다.

• 한국작물학회지
• /
• 제61권2호
• /
• pp.131-137
• /
• 2016

This study was conducted to investigate the effects of temperature and shade, which are basic environmental conditions, on growth, yield, inorganic components, and general components of Codonopsis lanceolata, in order to obtain basic data for improving yield capacity. In natural light, in the 15, 20, and $25^{\circ}C$ groups, the plant heights ranged between 218.9 cm and 223.9 cm, and there was no significant difference between groups. However, the leaf size was larger in shade, and the leaf area was significantly larger in the 15 and $30^{\circ}C$ groups. In natural light, root length and diameter were shorter and thinner when the temperature was higher, and growth was highly suppressed at $30^{\circ}C$. With regards to macroelements, the contents of Na, Mg, and P increased as temperature increased, regardless of the plant part; however, no constant tendency was observed in K and Ca according to temperature. The contents of Mg and Ca (from highest to lowest) were in the order leaf>stem>root, whereas the contents of Na, P, and K were in the order stem>leaf>root. Contents of general components varied according to temperature, and were highest at $30^{\circ}C$. While the plant height was increased under the constant $25^{\circ}C$+DIF (Difference between day and night temperature) condition, growth was suppressed in the -DIF group, in which the night temperature was higher than the day temperature, which suggests that a change in night temperature is one of the factors that affects the growth of C. lanceolata. As in the growth of the above-ground parts, fresh weight of the root was high in the constant $25^{\circ}C$ group and +DIF group. Notably, it was more than 2.5 times the fresh weights in the constant $15^{\circ}C$ group, constant $20^{\circ}C$ group, and -15 DIF group.

• Journal of Mechanical Science and Technology
• /
• 제20권4호
• /
• pp.513-521
• /
• 2006

The performances of porous bearings under different operating conditions were experimentally investigated in this study. Material groups studied are 90%Cu + 10%Sn bronze and 1%C + % balance Fe iron-based self-lubricating P/M bearings at constant (85%) density. In the experiments, the variation of the coefficient of friction and wear ratio of those two different group materials for different sliding speeds, loads, and temperatures were investigated. As a result, the variation of the friction coefficient-temperature for both constant load, and constant sliding speed, friction coefficient-average bearing pressure, PV-wear loss and temperature-wear loss curves were plotted and compared with each other for two materials, separately. The test results showed that Cu-based bearings have better friction and wear properties than Fe-based bearings.

• 한국세라믹학회지
• /
• 제19권4호
• /
• pp.316-320
• /
• 1982

The effect of the additive on dielectric properties of $BaTiO_3$ containing 0.030 mol% $Dy_2O_3$ was investigated function of frequency from 5$\times$104 to 0.3$\times$107cps and temperature from 25 to 1$25^{\circ}C$. The dielectric constant increased with increasing $Dy_2O_3$ concentration from 0 to 0.05mol% due to space charge polarization. However, the dielectric constant decreased for further increase of $Dy_2O_3$ concentration due to density increase. The dielectric constant exhibits rapid change at the Curie temperature and the Curie temperature drops from 122 to 116$^{\circ}C$ with increasing amount of $Dy_2O_3$ concentration.