• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.410-411
• /
• 2009

The multi-component ceramic proton conductor, $BaZr(Y)O_3-SiO_2-TiO_2-ZrO_2$ (BZY-STZ) and $LaPO_4-SiO_2-TiO_2-ZrO_2$ (LP-STZ), were synthesized by micro-emersion and sol-gel technique. The characterization of proton conductors were carried out using X-ray diffraction(XRD), thermogravimetric analysis(TGA), differential thermal analysis(DTA), impedance analysis. The proton conductors indicate the possibility of application for the intermediate temperature up to $700^{\circ}C$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.398-401
• /
• 2002

When the current flows over the allowable current due to the overload, it causes electric disaster such as an electrical fire and an electric shock by short current or leakage of electricity because the covering is deteriorated according to the heating action. In this paper, for the wire(IV 1.6mm) used as interior wiring, we analyzed a variation of the surroundings temperature, the form and the structure of a covering, and the crystal structure of a conductor. In the result of this experiment, the surroundings temperature at the allowable current of 300% rose to about 47$^{\circ}C$, and it rose up to the maximum allowable temperature of the wire at 400%. Consequently, it was broken within one minute at 500%. In the analysis of a metallograph, the conductor broken by the over current showed the dendrite. These analyses result will be applied to judging the electrical fire.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.365-366
• /
• 2015

This paper describes the analysis on thermo-mechanical characteristics of underground cable termination. Specially, the interface pressures between stress relief cone and XLPE insulation were analysed according to the change of conductor temperature and ambient temperature. This interface pressures were measured by real test with current transformer and chamber and the interface pressure was changed with conductor and ambient temperature. This paper will continue to perform the test with various cases, then the relation between low interface pressure and breakdown will prove with test results in the near future.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.376-378
• /
• 1999

In order to design the current carrying conductor for GIS, it is important to predict temperature-rise when rated current flows. This paper deals with the coupling of Flux2D and analytic method to calculate the heat transfer coefficient. Heat transfer by conduction and convection is considered between the current carrying conductor and $SF_6$ gas. The result shows reasonable temperature distribution.

• Proceedings of the KIEE Conference
• /
• 2003.07a
• /
• pp.247-249
• /
• 2003

This paper presents the analysis of the transient temperature rise at the surface of underground power cables and an estimation of conductor temperature considering the power load change of underground power cables.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.365-366
• /
• 2009

This study researched into the manufacture of current-limit module of using YBCO coated conductor. Regarding over-current of exceeding the critical current, the quench characteristics were researched according to the stabilizing layer through tendency in resistance, which is generated in conductor, by applying over-current to YBCO coated conductors, which have stabilizing layer. YBCO coated conductors, which were used in experiment, include one kind such as the conductor, which used stainless as the stabilizing layer. The critical current is 70 A. And, the critical temperature is with 90 K. First of all, the quench generation was researched under over-current of exceeding the critical current by using this YBCO coated conductors. The tendency of a rise in the detected voltage according to the applied current was measured. And, the tendency of a rise in resistance through voltage-current curve was measured. As a result, the point of time in thermal quench of conductor, which has stainless as the stabilizing layer, could be confirmed to be fast.

• Progress in Superconductivity and Cryogenics
• /
• v.10 no.1
• /
• pp.10-14
• /
• 2008

Differently from BSCCO tapes which are fabricated by powder-in-tube method, the coated conductors are made by the evaporation of YBCO on metal substrate. Due to this structural merit, although the coated conductors are generally used for large current transportation, they are expected to be favorable to the purpose of the fault current limitation as well. In this study, using YBCO coated conductor having copper stabilizer formed by plating technique(produced by Superpower Co.), we investigated the over-current characteristics of the coated conductor. The coated conductors had 85 A $I_c$ and 90 K $T_c$. The resistance of the conductor was 0.93 $m{\Omega}/cm$ at 300 K and 0.17 $m{\Omega}/cm$ at the temperature right above $T_c$. To the coated conductors, we applied the voltages of the range from 150 $V_{rms}$ to 230 $V_{rms}$ and measured the V-I curves using four probe method. From the results, we could analyze the electric behavior of the coated conductor in flux flow state. As the current exceed $I_c$, the currents were distributed into the superconductor and metal stabilizer. The amounts of the currents shared through both current paths were calculated under the assumption that the ,Joule heating was perfectly eliminated by $LN_2$ surrounding the conductor. Finally, the condition for the stable current flowing state which does not affect the conductor was established from the analysis on the over-current characteristics.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.8
• /
• pp.1154-1160
• /
• 2015

This paper describes the thermal characteristics of underground power cable system terminations according to the change of ambient temperature as well as operating temperature. Recently, the failure has been gradually increasing in outdoor termination during winter season because the power demand was increased by electricity heating system. The power demand and outdoor temperature is difference between day time and night time. The temperature difference has an influence on conductor extension and shrinkage due to conductor force as well as thermal mechanical characteristics. These phenomena have daily repeated during heating and cooling period of conductors. In these cases, the insulation of outdoor terminations might be degraded by the reduced interface pressure surrounding stress relief cone. Therefore, in this paper, the thermal characteristics are variously analysed by simulation considering power demand and ambient temperature condition during winter season at epoxy type termination as well as slip-on type termination

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.297-299
• /
• 2002

To wind a HTS (High Temperature Superconductor) tape conductor on a bobbin, double pancake winding technique is widely used to reduce number of splicing contacts between conductor pieces. However, this makes some Ic (critical current) degradation on kink points which is unavoidable. This paper describes the two ways of winding; usual double pancake and soldered double pancake. Characteristics of the two windings are measured and compared.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2002.11a
• /
• pp.169-172
• /
• 2002

Silver pastes for inner conductor in the Low Temperature Co-fired Ceramics (LTCC) are composed of silver powder, binder, solvent and additives. The composition of the chemicals have influence on rheology, printability, shrinkage rate, etc. In this study, commercial Ag pastes and Ag pastes made in KETI were investigated to find the relationship between characteristics of Ag paste and solid contents. Ag pastes with 68~90 wt% Solid Contents were tested. Substrate/paste matching property and conductivity of the conductor lines showed large dependence on solid contents of Ag paste.