• Journal of Electrical Engineering and Technology
• /
• 제8권1호
• /
• pp.176-182
• /
• 2013

In this study, we examine the tracking happen in a polyvinyl-chloride-sheathed flat cord (PVCSFC), which is widely used as a distribution cord. The study classifies the bridge current via the formed conductive paths during tracking in the PVCSFC. Further, it attempts to distinguish the characteristics of heat generation and heat transfer by kind of bridge current. When the PVCSFC is in the static state, the bridge currents flow only through the electrolyte bridge. In the case of the carbonized PVCSFC, the bridge currents flow through one or more conductive paths. One is the electrolyte bridge, the other is the bridge that is consisted electrolyte and carbonized insulation. Currents flowing through different conductive paths have different heat generation and transfer characteristics. As the bridge current flowing in the conductive path consisting of electrolyte and carbonized insulation increases, the temperature difference between the surface of the PVCSFC and ambient air also increases correspondingly.

• 한국전기전자재료학회논문지
• /
• 제32권3호
• /
• pp.241-245
• /
• 2019

This work presents the response characteristics of a ZnO varistor to conductive EMP. An E1 pulse, standardized to MIL-STD-188-125-1, was applied to the varistors wherein the residual current and response times were measured with the applied E1 pulse current. Additionally, the response time was measured according to the length of the connection path. Consequently, the amplitude of the residual voltage through the ZnO varistors was increased with increasing amplitude of the applied E1 pulse current. As the length of the connection path increased, the operating response time and residual peak voltage also increased. These results indicate that the response characteristics of ZnO varistors can be applied to basic data to support the use of varistors as a protective measure against conductive EMP.

• 한국정밀공학회지
• /
• 제26권1호
• /
• pp.105-111
• /
• 2009

Dielectric breakdown in piezoelectric ceramics is analyzed by using the three dimensional J integral. The J integral is shown to be a path-independent surface integral for a conductive tubular channel in a piezoelectric material. J integrals are also numerically calculated for conductive defects and tubular channels in piezoelectric ceramics through finite element analysis.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1525-1526
• /
• 2006

Electrical current always travels through the minimum resistance path. In this paper, we are studied on the direction and formation of carbonized conductive path according to surface leakage between electrodes. The analysis of characteristics of the arc discharge as surface is broken down between exposed live parts. Using the HSIS(high speed imaging system, 100,000fps, redlake ltd., USA), it took photographs by arc growth mechanism occurred in on/off surge, ground fault and discharge between electrodes. Therefore, it recommended for results of technology development and application such as theoretic verification of an arc direction and economic security according to a technology about connecting arc generation in surfaces of insulators. Hereafter, it expected effects that application of energy utility technology through the arc control.

• 조명전기설비학회논문지
• /
• 제21권2호
• /
• pp.28-33
• /
• 2007

본 논문에서 전극간 표면누설에 의한 탄화도전로의 형성과 방향성에 대해 연구하였다. 표면에서 트래킹의 특성은 노출된 충전부사이에서 절연파괴되었다. 고속카메라시스템을 이용하여 전극간 방전과 지락, on/off 서어지에서 발생되는 아크성장 메커니즘을 촬영하고, 결과를 분석하였다. 향후 아크제어를 통한 에너지 이용기술의 적용이 기대된다.

• Journal of Electrical Engineering and Technology
• /
• 제6권5호
• /
• pp.688-692
• /
• 2011

Carbon nanotubes (CNTs) are vertically grown inside high-aspect-ratio vertical pores of anodized aluminum oxide. A CNT catalyst layer is introduced by atomic layer deposition to the bottom of the pores, after which the CNTs are successfully grown from the layer using chemical vapor deposition. The CNTs formed a complete vertical conductive path. The conductivity of the CNT-vertical path is also measured and discussed. The present atomic layer deposition-incorporated catalyst deposition is predicted to enable the integration of CNTs with various challenging configurations, including high-aspect-ratio vertical channels or vertical interconnects.

• 반도체디스플레이기술학회지
• /
• 제15권4호
• /
• pp.10-15
• /
• 2016

In this paper, novel ball grid array (BGA) interconnection process using solderable anisotropic conductive adhesives (SACAs) with low-melting-point alloy (LMPA) fillers have been developed to enhance the processability in the conventional capillary underfill technique and to overcome the limitations in the no-flow underfill technique. To confirm the feasibility of the proposed technique, BGA interconnection test was performed using two types of SACA with different LMPA concentration (0 and 4 vol%). After the interconnection process, the interconnection characteristics such as morphology of conduction path and electrical properties of BGA assemblies were inspected and compared. The results indicated that BGA assemblies using SACA without LMPA fillers showed weak conduction path formation such as solder bump loss or short circuit formation because of the expansion of air bubbles within the interconnection area due to the relatively high reflow peak temperature. Meanwhile, assemblies using SACA with 4 vol% LMPAs showed stable metallurgical interconnection formation and electrical resistance due to the favorable selective wetting behavior of molten LMPAs for the solder bump and Cu metallization.

• 한국산학기술학회논문지
• /
• 제19권9호
• /
• pp.13-19
• /
• 2018

MWCNT (다중벽 탄소 나노튜브)의 종류와 유동 형태가 폴리카보네이트 (PC)/MWCNT 나노 복합체의 전기 전도도에 미치는 영향을 관찰하였다. MWCNT의 종류가 바뀌면 사출 성형으로 제조된 PC/MWCNT의 전기 전도도가 크게 변하는 것을 관찰하였다. MWCNT 의 종횡비가 클수록 사출 성형품의 전기 전도도는 낮았고 압축 성형으로 제조한 시료의 전기 전도도는 MWCNT의 종류에 상관없이 비슷하였다. 이 결과는 MWCNT의 변형과 크게 상관있는 것으로 조사되었다. 종횡비가 클수록 외부 응력이 작용할 때 MWCNT의 배향도가 올라가고 MWCNT들의 접촉에 의한 전도성 길 (path)가 끊어져서 전기전도도가 낮아지는 것으로 생각된다. 연신력과 전단 속도가 큰 조건에서 제조된 시료의 전기 전도도가 크게 낮아지는 것을 관찰하였다. 이는 높은 전단력과 연신력에서 MWCNT의 배향이 높아지고 그 결과 MWCNT 들의 접촉이 단절되면서 전기 전도도가 낮아지는 것임을 다양한 실험으로 부터 알 수 있었다. 여러 실험 결과 들을 MWCNT의 배향과 전도길 변화와의 연관성의 관점으로 토의하였다.

• Bulletin of the Korean Chemical Society
• /
• 제33권8호
• /
• pp.2529-2534
• /
• 2012

Poly(3,4-ethylenedioxythiophene) coated Manganese Dioxide (PEDOT/$MnO_2$) composite electrode was fabricated by simply immersing the $MnO_2$ electrode in an acidic aqueous solution containing 3,4-ethylenedioxythiophene (EDOT) monomers. Analysis of open-circuit potential of the $MnO_2$ electrode in the solution indicates the reduction of outer surface of $MnO_2$ to dissolved $Mn^{2+}$ ions and simultaneously oxidation of EDOT monomer to PEDOT on the $MnO_2$ surface to form a PEDOT shell via a galvanic displacement reaction. Analysis of cyclic voltammograms and specific capacitance of the PEDOT/$MnO_2$, conductive carbon added $MnO_2$ and conductive carbon added PEDOT/$MnO_2$ electrodes suggests that the conductive carbon acted mainly to provide a continuous conducting path in the electrode to improve the rate capability and the PEDOT layer on $MnO_2$ acts to increase the active reaction site of $MnO_2$.

• 조명전기설비학회논문지
• /
• 제22권2호
• /
• pp.155-161
• /
• 2008

접지시스템은 고장전류나 상시 전류를 낮은 저항의 대지로 흘러 보낸다. 접지전극 주변에 접지저감재를 매설하면 접촉 면적을 증가시켜 낮은 접지저항을 얻을 수 있다. 접지전극의 접촉면적을 확대시키면 접지저항값이 낮아진다는 특성을 이용하여 접지 시공시 팽창 특성을 가진 도전성 팽창 접지저감재를 개발하였다. 본 논문에서는 실험을 통하여 도전성 팽창 접지저감재가 일반 접지저감재보다 접지저항 저감 효과가 뛰어남을 검증하였다.