• Journal of Electrical Engineering and Technology
• /
• v.8 no.1
• /
• pp.176-182
• /
• 2013

In this study, we examine the tracking happen in a polyvinyl-chloride-sheathed flat cord (PVCSFC), which is widely used as a distribution cord. The study classifies the bridge current via the formed conductive paths during tracking in the PVCSFC. Further, it attempts to distinguish the characteristics of heat generation and heat transfer by kind of bridge current. When the PVCSFC is in the static state, the bridge currents flow only through the electrolyte bridge. In the case of the carbonized PVCSFC, the bridge currents flow through one or more conductive paths. One is the electrolyte bridge, the other is the bridge that is consisted electrolyte and carbonized insulation. Currents flowing through different conductive paths have different heat generation and transfer characteristics. As the bridge current flowing in the conductive path consisting of electrolyte and carbonized insulation increases, the temperature difference between the surface of the PVCSFC and ambient air also increases correspondingly.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.3
• /
• pp.241-245
• /
• 2019

This work presents the response characteristics of a ZnO varistor to conductive EMP. An E1 pulse, standardized to MIL-STD-188-125-1, was applied to the varistors wherein the residual current and response times were measured with the applied E1 pulse current. Additionally, the response time was measured according to the length of the connection path. Consequently, the amplitude of the residual voltage through the ZnO varistors was increased with increasing amplitude of the applied E1 pulse current. As the length of the connection path increased, the operating response time and residual peak voltage also increased. These results indicate that the response characteristics of ZnO varistors can be applied to basic data to support the use of varistors as a protective measure against conductive EMP.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.1
• /
• pp.105-111
• /
• 2009

Dielectric breakdown in piezoelectric ceramics is analyzed by using the three dimensional J integral. The J integral is shown to be a path-independent surface integral for a conductive tubular channel in a piezoelectric material. J integrals are also numerically calculated for conductive defects and tubular channels in piezoelectric ceramics through finite element analysis.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1525-1526
• /
• 2006

Electrical current always travels through the minimum resistance path. In this paper, we are studied on the direction and formation of carbonized conductive path according to surface leakage between electrodes. The analysis of characteristics of the arc discharge as surface is broken down between exposed live parts. Using the HSIS(high speed imaging system, 100,000fps, redlake ltd., USA), it took photographs by arc growth mechanism occurred in on/off surge, ground fault and discharge between electrodes. Therefore, it recommended for results of technology development and application such as theoretic verification of an arc direction and economic security according to a technology about connecting arc generation in surfaces of insulators. Hereafter, it expected effects that application of energy utility technology through the arc control.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.21 no.2
• /
• pp.28-33
• /
• 2007

In this paper, we are studied on the direction and formation of carbonized conductive path according to surface leakage current between electrodes. The characteristics of the tracking as surface is broken down between exposed live parts. Using the HSIS(high speed imaging system. 100,000[fps], redlake ltd., USA), it took photographs by arc growth mechanism occurred in on/off surge, ground fault and discharge between electrodes. Then the results was analyzed. Hereafter, it expected effects that application of energy utility technology through the arc control.

• Journal of Electrical Engineering and Technology
• /
• v.6 no.5
• /
• pp.688-692
• /
• 2011

Carbon nanotubes (CNTs) are vertically grown inside high-aspect-ratio vertical pores of anodized aluminum oxide. A CNT catalyst layer is introduced by atomic layer deposition to the bottom of the pores, after which the CNTs are successfully grown from the layer using chemical vapor deposition. The CNTs formed a complete vertical conductive path. The conductivity of the CNT-vertical path is also measured and discussed. The present atomic layer deposition-incorporated catalyst deposition is predicted to enable the integration of CNTs with various challenging configurations, including high-aspect-ratio vertical channels or vertical interconnects.

• Journal of the Semiconductor & Display Technology
• /
• v.15 no.4
• /
• pp.10-15
• /
• 2016

In this paper, novel ball grid array (BGA) interconnection process using solderable anisotropic conductive adhesives (SACAs) with low-melting-point alloy (LMPA) fillers have been developed to enhance the processability in the conventional capillary underfill technique and to overcome the limitations in the no-flow underfill technique. To confirm the feasibility of the proposed technique, BGA interconnection test was performed using two types of SACA with different LMPA concentration (0 and 4 vol%). After the interconnection process, the interconnection characteristics such as morphology of conduction path and electrical properties of BGA assemblies were inspected and compared. The results indicated that BGA assemblies using SACA without LMPA fillers showed weak conduction path formation such as solder bump loss or short circuit formation because of the expansion of air bubbles within the interconnection area due to the relatively high reflow peak temperature. Meanwhile, assemblies using SACA with 4 vol% LMPAs showed stable metallurgical interconnection formation and electrical resistance due to the favorable selective wetting behavior of molten LMPAs for the solder bump and Cu metallization.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.9
• /
• pp.13-19
• /
• 2018

Effects of multiwall carbon nanotube (MWCNT) type and flow type (shear and elongational flow) on the electrical conductivity of polycarbonate (PC)/ MWCNT nanocomposites were investigated. Two different MWCNTs produced a huge difference in electrical conductivity in an injection molded PC/MWCNT nanocomposite. It was observed that MWCNTs having a higher aspect ratio provide much lower electrical conductivity in injection molded PC/MWCNT nanocomposites while the conductivities of compression molded samples from two different MWCNTs were the same. We found that this is due to a difference in the deformability of the two MWCNTs. As the aspect ratio of the MWCNT increases, the orientation of MWCNT by the external force becomes easier and the conductive path diminishes. Consequently the conductivity of the nanocomposites decreases. Nanocomposite samples prepared at a higher extensional rate and shear rate showed lower electrical conductivity. This is also attributed to the flow induced orientation and reduced conductive path of the MWCNTs. The experimental results were discussed in relation to variation in the tube-tube contact due to the change of the MWCNT orientation.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.8
• /
• pp.2529-2534
• /
• 2012

Poly(3,4-ethylenedioxythiophene) coated Manganese Dioxide (PEDOT/$MnO_2$) composite electrode was fabricated by simply immersing the $MnO_2$ electrode in an acidic aqueous solution containing 3,4-ethylenedioxythiophene (EDOT) monomers. Analysis of open-circuit potential of the $MnO_2$ electrode in the solution indicates the reduction of outer surface of $MnO_2$ to dissolved $Mn^{2+}$ ions and simultaneously oxidation of EDOT monomer to PEDOT on the $MnO_2$ surface to form a PEDOT shell via a galvanic displacement reaction. Analysis of cyclic voltammograms and specific capacitance of the PEDOT/$MnO_2$, conductive carbon added $MnO_2$ and conductive carbon added PEDOT/$MnO_2$ electrodes suggests that the conductive carbon acted mainly to provide a continuous conducting path in the electrode to improve the rate capability and the PEDOT layer on $MnO_2$ acts to increase the active reaction site of $MnO_2$.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.2
• /
• pp.155-161
• /
• 2008

The grounding systems provide a low resistance path for fault or normal currents into the earth. The material for reducing ground resistance is buried around the grounding electrode to increase its effective size of the electrode and thus to obtain low ground resistance. Increasing the contacting area with the grounding electrode is effective for lowering the ground resistance in soils. Using this idea the conductive expansion ground resistance reducing material was developed. In this paper experimental data has shown that the ground resistance reduction method using proposed material is superior to using a typically available commercial ground resistance reducing material.