• Journal of the Korea institute for structural maintenance and inspection
• /
• v.15 no.4
• /
• pp.185-192
• /
• 2011

A CFRP (Carbon Fiber-Reinforced Plastic) strengthening method being widely used to increase the load-carrying capacity of structures is very suitable for existing bridge structures. However, not only flexure and shear failures but also debonding failure might be additionally occured in reinforced concrete(RC) beams strengthened with the CFRP plates. The CFRP debonding failure would cause a brittle fracture of the beam. Therefore, health monitoring for the CFRP bonding condition is strongly required. In this study, a feasibility of the impedance-based damage detection method using PZT sensors was investigated through a series of experimental studies for realtime structural health monitoring(SHM) for the CFRP laminated concrete structures.

• Smart Structures and Systems
• /
• v.21 no.2
• /
• pp.171-185
• /
• 2018

Maintenance of deteriorated bridge structures has always been one of the challenging issues in developing countries as it is directly related to daily life of people including trade and economy. An effective maintenance strategy is highly dependent on timely inspections on the bridge health condition. This study is intended to investigate an approach for detecting bridge damage for the long-term health monitoring by use of copula theory. Long-term measured data for the seven-span plate-Gerber bridge is investigated. Autoregressive time series models constructed for the observed accelerations taken from the bridge are utilized for the computation of damage indicator for the bridge. The copula model is used to analyze the statistical changes associated with the modal parameters. The changes in the modal parameters with the time are identified by the copula statistical properties. Applicability of the proposed method is also discussed based on a comparison study among other approaches.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.3
• /
• pp.91-100
• /
• 2017

The solution was developed for the maintenance decision support of combined cycle power plant gas turbine. The developed solution was applied to MHI501G gas turbine and is, in present, on the process of field test at GUNSAN combined cycle power plant, South Korea. The developed solution provides the calculated result of optimal overhaul maintenance period through following modules: Real Time Performance Monitoring, Model-Based Diagnostics, Performance Trend Analysis, Optimal Overhaul Maintenance Interval, Compressor Washing Period Management, and Blade Path Temperature Analysis. Model-Based Diagnostics module analyzed the differences between the data of gas turbine performance model and the online measurement. Compressor washing management module suggests the optimal point of balancing between the compressor performance and the maintenance cost.

• International Journal of CAD/CAM
• /
• v.6 no.1
• /
• pp.9-17
• /
• 2006

Performing inspections for Hull Condition Monitoring and Assessment as stipulated in IACS unified requirements and IMO's Condition Assessment Scheme (CAS) IMO Resolution MEPC.94(46), 2001, Condition Assessment Scheme, IMO Resolution MEPC.111(50), 2003, Amendments to regulation 13G, addition of new regulation 13H involves a huge amount of measurement data to be collected, processed, analysed and maintained. Information to be recorded consists of thickness measurements and visual assessment of coating and cracks. The amount of data and increasing requirements with respect to condition assessment demand efficient computer support. Currently, due to the lack of standardization for this kind of data, the thickness measurements are recorded manually on ship drawings or tables. In this form, handling of the measurements is tedious and error-prone and assessment is difficult. Data reporting and analysis takes a long time, leading to some repairs being performed only at the next docking of the ship or making an additional docking necessary. The recently started ED funded project CAS addresses this topic and develops-as a first step-a data model for Hull Condition Monitoring and Assessment (HCMA) based on XML-technology. The model includes simple geometry representation to facilitate a graphically supported data collection as well as an easy visualisation of the measurement results. In order to ensure compatibility with the current way of working, the content of the data model is strictly confined to the requirements of the measurement process. Appropriate data interfaces to classification software will enable rapid assessment by the classification societies, thus improving the process in terms of time and cost savings. In particular, decision-making can be done while the ship is still in the dock for maintenance.

• Structural Monitoring and Maintenance
• /
• v.1 no.2
• /
• pp.159-171
• /
• 2014

Real-time near and far-field monitoring of concrete structural components gives enough information on the time and condition at which damage occurs, thereby facilitating damage detection while in the same time evaluate the cause of the damage. This paper experimentally investigates an integrated monitoring technique for near and far-field damage detection in concrete structures based on simultaneous use of electromechanical admittance technique in combination with guided wave propagation. The proposed sensing system does not measure the electromechanical admittance itself but detect time variations in output voltages of the response signal obtained across the electrodes of piezoelectric transducers bonded on surfaces of concrete structures. The damage identification is based on the spectral estimation MUSIC algorithm. Experimental results show the efficiency and performance of the proposed measuring technique.

• Journal of Institute of Control, Robotics and Systems
• /
• v.17 no.5
• /
• pp.412-418
• /
• 2011

The scale of wind turbines has continuously increased over the last decade. Especially, the rapid growth of the rotor diameter has brought about the increase of the tower height and the load on the rotor blade, as can be seen in the case of a 5MW class wind turbine with 126m rotor diameter. This trend means the increasing possibility of system failure. In addition to that, it is impossible for human operators to stay and manage all the turbines in the case of a large-scale wind farm. For these reasons, the operation and maintenance technology is getting more importance. In this paper, we present an unmanned remote monitoring system for MW class wind turbines and its application to YeungHeung wind test bed.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.1545-1561
• /
• 2008

Among all transportations, railway transports have been promisingly offering excellent energy conservation and travelling time. Inevitably, they become a main role in not only transport goods but also passengers. With leap in development of technology, trains have tremendously enhanced their services in terms of speed, accessibility and comfort. However, the safety and ride quality have become a main issue as the train speed increased. The higher speeds have led the structural dynamics and health must be monitored from time to time to ensure that they are in good condition to provide reliable ride. Among all monitoring systems, the structural health monitoring (SHM) systems are imperative important due to its capability of in-situ monitoring and inherently reduce the maintenance frequencies and the huge associated cost. In this paper, SHM systems and the related non-destructive test and evaluation methods were discussed. The types of damages related to train vehicles as well as the damage hot spots are also included in this paper.

• Proceedings of the KIEE Conference
• /
• 1999.07e
• /
• pp.2212-2214
• /
• 1999

In this paper, a novel Generator On-line Diagnosis System (GODS) is proposed. This system monitors the insulation condition of the stator winding by on-line measurements of partial discharge (PD). Sensor, such as SSC (Stator Slot Coupler) and RFCT (Radio Frequency Current Transformer) are used for PD measurement. PD signals are continuously measured and digitized with a high speed A/D converter to build the database of the generator's insulation condition. Also this system can communicate with the central monitoring system via RS-485. This helps more efficient operation and maintenance of the generator.

• Proceedings of the Safety Management and Science Conference
• /
• 2005.05a
• /
• pp.259-266
• /
• 2005

In this paper, we developed a vehicle condition monitoring system that checks vehicle conditions, and transmits and displays them to a driver for safety and effective maintenance. We used a CAN controller and transceiver to establish the CAN communication that has been used commonly inside an actual vehicle for the collection of vehicle's status information. To validate the operation of the developed system, we have confirmed the accuracy and stability of data transmission and reception of vehicle information.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1894-1896
• /
• 2003

In this paper, a novel monitoring system, data acquisition & diagnosis unit (DADU), for high-voltage rotating machines is proposed. This system monitors the insulation condition, current, voltage, vibration, and temperature of the stator winding by on-line measurements of partial discharge (PD), flux, etc. This helps more efficient operation and maintenance of the rotating machines.