• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 가을 학술발표회 논문집
• /
• pp.289-292
• /
• 2003

CFRD face slab concrete has a much capability to occur crack due to drying shrinkage and vibrator compaction etc. Because crack of concrete induces structural problem and decrease durability of concrete, it is need to reduce crack of concrete. In the experimental study it was analyzed that the effect of curing of concrete and compaction on CFRD face slab concrete. As a results, it was found that control of construction condition into curing of concrete and compaction improved on construction efficiency of face slab concrete.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1996년도 봄 학술발표회 논문집
• /
• pp.42-47
• /
• 1996

Due to high increase of labor charge and necessarity of better quality control on concrete, various studies have been carried out to improve a flowability of concrete without the use of mechanical vibrator. As a result of enthusiastic study, one can closely access to the development of high flowable concrete in a laboratorial view. Application to practical field, however, is still far as long as a regulation for construction is not properly specified. Based on the idea that lateral pressure measured from high flowable concrete will be larger than those from general typed concrete, we read a series of lateral pressure from mechanical pressure plate and compared those with the values calculated form specified formula.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.953-958
• /
• 2002

The finishing method of concrete floor using automatic surface finisher is one of new technologies in concrete floor construction. The development of high technologies in construction will increase in order to satisfy the demand to construct high quality building. Using this method, it is possible to increase the quality of building as well as to reduce the labor work in site. In this paper, a system which can be used to finish the concrete floor using automatic surface finisher, is presented and its structural capacities are evaluated. The system is composed of rail which guides the surface vibrator and absorbs the volume change of concrete, and a device supporting the rail. From the experimental work for these devices, it was shown that the support and rail had suitable strength to resist the automatic surface finisher. For design purpose, also, effective span of supports was tabulated.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 봄 학술발표회 논문집
• /
• pp.521-526
• /
• 1997

The Spin Tester(High Speed Balancing and Overspeed Test Facility), which is designed for the quality control of turbine, generator, and rotors was supposed to be constructed with the use of Steel Fiber Reinforced Concrete(SERC) for reducing the risk of accident while operation. However, it was very existence of fiber concrete due to there are two major concern in the SFRC work: one is existence of fiber ball due to inhomogeneous mixing, the other is the segregation of the concrete materials. To avoid these possible problems, the S/a was controlled about 55% to reduce the segregation and the high range AE water reducing agent was used to maintain the slump over the value of 18cm. With these careful consideratons, the SFRC work was done successfully by only using regular equipments like pump car and vibrator.

• Computers and Concrete
• /
• 제17권2호
• /
• pp.271-280
• /
• 2016

This study examined the mechanical properties and adiabatic temperature rise of low-heat concrete developed based on ternary blended cement using ASTM type IV (LHC) cement, ground fly ash (GFA) and limestone powder (LSP). To enhance reactivity of fly ash, especially at an early age, the grassy membrane was scratched through the additional vibrator milling process. The targeted 28-day strength of concrete was selected to be 42 MPa for application to high-strength mass concrete including nuclear plant structures. The concrete mixes prepared were cured under the isothermal conditions of $5^{\circ}C$, $20^{\circ}C$, and $40^{\circ}C$. Most concrete specimens gained a relatively high strength exceeding 10 MPa at an early age, achieving the targeted 28-day strength. All concrete specimens had higher moduli of elasticity and rupture than the predictions using ACI 318-11 equations, regardless of the curing temperature. The peak temperature rise and the ascending rate of the adiabatic temperature curve measured from the prepared concrete mixes were lower by 12% and 32%, respectively, in average than those of the control specimen made using 80% ordinary Portland cement and 20% conventional fly ash.

• 한국산학기술학회논문지
• /
• 제20권3호
• /
• pp.465-469
• /
• 2019

본 논문에서는 콘크리트 바이브레이터에 Slotless BLDC (Brush Less Direct Current) 모터를 적용하기 위해 BLDC 모터의 토크 및 역기전력 식을 기반으로 하여 설계를 한다. 모터의 길이와 직경의 사이즈가 주어져 있으므로 중요한 파라미터는 공극자속밀도이다. 자기회로의 간략화를 통하여 공극자속밀도를 계산 하였으며, 토크, 역기전력 및 공극자속밀도 식을 기반으로 기초설계를 진행하여 모터의 형상을 결정 하였다. 이후 모터의 고정자의 외경 및 내경, 스택 길이, 속도를 고정값으로 설정한 후 모터의 직경 및 두께를 변수로 지정하여 유한요소법을 이용한 시뮬레이션을 통해 상세설계를 진행하였으며, THD(Total Harmonic Distortion)값이 작으면서 목표 토크 값 이상의 형상을 설계 및 시뮬레이션을 진행하였다.

• 한국건축시공학회지
• /
• 제9권1호
• /
• pp.49-55
• /
• 2009

In this study, reduction methods of surface air void were examined for high performance concrete having high viscosity. The effects of assumed influencing factors such as form types, form-coating materials, tamping equipments and methods were examined based on the tests on mock-up specimens made of high performance concrete. The test results can be summarized as follows: As for form types, the most favorable results were obtained when coated plywood form was used with panel-shape tamping equipments at the contact region with concrete, the second and the third being the water/air-permeable sheets and steel with coated plywood, respectively. As for tamping equipments, a vibrator with 6.5cm diameter was most effective. Finally, the shorter the tamping intervals, the better the reduction effect of surface air void. As a conclusion, an improved method was proposed to reduce surface air void and it was verified with the test result that only four air voids as large as $5{\sim}10mm$ are found in the are of $1m^2$.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 추계 학술발표회 제20권2호
• /
• pp.509-512
• /
• 2008

라이닝콘크리트란 터널의 영구적인 라이닝으로서 무근 또는 철근콘크리트로 구축되는 터널의 가장 내측에 시공되는 터널의 부재를 말하며. 라이닝의 목적은 터널주변 암반의 풍화방지 및 유수에 의한 지반열화 경감, 터널의 내구성 증대 등이다. 라이닝시 콘크리트는 시공불량, 내부응력, 건조수축 등에 따라 균열을 야기할 수 있으며, 콘크리트 구조물에서 발생하는 이러한 균열은 내구성의 저하와 외관의 손상을 초래하여 사용성을 저하시킬 뿐만 아니라, 균열로 인한보수비용을 증대시킨다. 본 연구는 직경이 15m 이상의 대단면 터널의 라이닝콘크리트의 실제 현장에서 발생한 균열에 대하여 발생하는 균열에 대한 구조, 재료에 대한 분석을 수행하였으며, 그 결과를 제시하므로서 합리적이고 효율적인 대단면 터널 라이닝콘크리트의 균열에 대한 대책을 제시하고자 한다.금번 검토 결과, 구조적 특성에 의한 것이 아님을 알 수 있었으며 다음과 같이 몇가지 원인에 대한대책을 통해 균열을 저감할 수 있을 것이다. 1) 하절기배합인 플라이애쉬 20% 배합으로 변경하면, 수화열 저감효과와 함께 초결시간 지연 효과도 가져올 수 있으므로 연직균열 및 수평균열에 유리한 조건을 만들어 줄 수 있을 것으로 사료된다. 2) 균열이 주로 발생된 S.L 부근의 다짐방법과 관련하여 다음과 같이 개선코자 한다. 즉, 3단과 4단투입구간(間)계면 방지를 위하여 4단 투입구를 통하여 일부 콘크리트를 타설 후 타설중지 상태에서 3단과 4단 투입 콘크리트를 같이 다짐을 실시한다. 이 때 주의할 점은 3단 타설 콘크리트의 초결 이전에 재다짐이 되어야 하므로 전체 시간을 6시간 이내에 완료해야 한다(플라이애쉬 20% 혼입 조건). 3) 일단 S.L 부근까지 콘크리트를 타설한 후, 하단부 콘크리트가 충분히 침강이 일어날 수 있도록 30분 내외 타설을 중지하였다가 후속 콘크리트를 타설토록 한다.

• Structural Engineering and Mechanics
• /
• 제39권2호
• /
• pp.241-266
• /
• 2011

The Self Compacting Concrete, SCC is the new generation type of concrete which is not needed to be compacted by vibrator and it will be compacted by its own weight. Since SCC is a new innovation and also the high strength self compacting concrete, HSSCC behavior is like a brittle material, therefore, understanding the strength effect on the serviceability performance of reinforced self compacting concretes is critical. For this aim, first the normal and high strength self compacting concrete, NSSCC and HSSCC was designed. Then, the serviceability performance of reinforced connections consisting of NSSCC and HSSCC were investigated. Twelve reinforced concrete connections (L = 3 m, b = 0.15 m, h = 0.3 m) were simulated, by this concretes, the maximum and minimum reinforcement ratios ${\rho}$ and ${\rho}^{\prime}$ (percentage of tensile and compressive steel reinforcement) are in accordance with the provision of the ACI-05 for conventional RC structures. This study was limited to the case of bending without axial load, utilizing simple connections loaded at mid span through a stub (b = 0.15 m, h = 0.3 m, L = 0.3 m) to simulate a beam-column connection. During the test, concrete and steel strains, deflections and crack widths were measured at different locations along each member. Based on the experimental readings and observations, the cracked moment of inertia ($I_{cr}$) of members was determined and the results were compared with some selective theoretical methods. Also, the flexural crack widths of the members were measured and the applicability for conventional vibrated concrete, as for ACI, BS and CSA code, was verified for SCCs members tested. A comparison between two Codes (ACI and CSA) for the theoretical values cracking moment is indicate that, irrespective of the concrete strength, for the specimens reported, the prediction values of two codes are almost equale. The experimental cracked moment of inertia $(I_{cr})_{\exp}$ is lower than its theoretical $(I_{cr})_{th}$ values, and therefore theoretically it is overestimated. Also, a general conclusion is that, by increasing the percentage of ${\rho}$, the value of $I_{cr}$ is increased.

• 수산해양기술연구
• /
• 제53권1호
• /
• pp.41-48
• /
• 2017

Encircling gill net fishery is a kind of gill net which is generally used in shallow coastal waters. After the fish have been encircled by the gill net, noise stimulus such as a stone or sound is used to force them to gill or entangle themselves in the netting surrounding them. Although the fishing by a stone is a traditional fishing method, it is considered as an illegal fishing method by physical stimulus such as explosives and mechanical vibrator. However, this illegal fishing method has raised some problems to the fishing boat of other fisheries or many anglers due to disturb aggregating fish schools. This study is aimed to provide scientific base data to verify whether to impact the ecosystem caused by this encircling gill net. This study exhibited that the impulse noise by concrete sphere in the encircling gill net was $159dB/{\mu}Pa$, the ambient noise from ship engine was $160dB/{\mu}Pa$, and the maximum noise from continuous artificial vibrator was $175dB/{\mu}Pa$. These may be stimulus to the escape of fish distributed in a wide area in its natural state; it is not likely the cause of death due to catastrophic stress. Therefore, it needs to prepare the consideration of standard limit on fishing stimulus in fishing methods of the fishery laws and regulations, prevent fishermen form using illegal fishing gear (i.e. explosive sound standards: $200{\sim}220dB/{\mu}Pa$ and provide them with countermeasures.