• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.11a
• /
• pp.289-292
• /
• 2003

CFRD face slab concrete has a much capability to occur crack due to drying shrinkage and vibrator compaction etc. Because crack of concrete induces structural problem and decrease durability of concrete, it is need to reduce crack of concrete. In the experimental study it was analyzed that the effect of curing of concrete and compaction on CFRD face slab concrete. As a results, it was found that control of construction condition into curing of concrete and compaction improved on construction efficiency of face slab concrete.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1996.04a
• /
• pp.42-47
• /
• 1996

Due to high increase of labor charge and necessarity of better quality control on concrete, various studies have been carried out to improve a flowability of concrete without the use of mechanical vibrator. As a result of enthusiastic study, one can closely access to the development of high flowable concrete in a laboratorial view. Application to practical field, however, is still far as long as a regulation for construction is not properly specified. Based on the idea that lateral pressure measured from high flowable concrete will be larger than those from general typed concrete, we read a series of lateral pressure from mechanical pressure plate and compared those with the values calculated form specified formula.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2002.05a
• /
• pp.953-958
• /
• 2002

The finishing method of concrete floor using automatic surface finisher is one of new technologies in concrete floor construction. The development of high technologies in construction will increase in order to satisfy the demand to construct high quality building. Using this method, it is possible to increase the quality of building as well as to reduce the labor work in site. In this paper, a system which can be used to finish the concrete floor using automatic surface finisher, is presented and its structural capacities are evaluated. The system is composed of rail which guides the surface vibrator and absorbs the volume change of concrete, and a device supporting the rail. From the experimental work for these devices, it was shown that the support and rail had suitable strength to resist the automatic surface finisher. For design purpose, also, effective span of supports was tabulated.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.04a
• /
• pp.521-526
• /
• 1997

The Spin Tester(High Speed Balancing and Overspeed Test Facility), which is designed for the quality control of turbine, generator, and rotors was supposed to be constructed with the use of Steel Fiber Reinforced Concrete(SERC) for reducing the risk of accident while operation. However, it was very existence of fiber concrete due to there are two major concern in the SFRC work: one is existence of fiber ball due to inhomogeneous mixing, the other is the segregation of the concrete materials. To avoid these possible problems, the S/a was controlled about 55% to reduce the segregation and the high range AE water reducing agent was used to maintain the slump over the value of 18cm. With these careful consideratons, the SFRC work was done successfully by only using regular equipments like pump car and vibrator.

• Computers and Concrete
• /
• v.17 no.2
• /
• pp.271-280
• /
• 2016

This study examined the mechanical properties and adiabatic temperature rise of low-heat concrete developed based on ternary blended cement using ASTM type IV (LHC) cement, ground fly ash (GFA) and limestone powder (LSP). To enhance reactivity of fly ash, especially at an early age, the grassy membrane was scratched through the additional vibrator milling process. The targeted 28-day strength of concrete was selected to be 42 MPa for application to high-strength mass concrete including nuclear plant structures. The concrete mixes prepared were cured under the isothermal conditions of $5^{\circ}C$, $20^{\circ}C$, and $40^{\circ}C$. Most concrete specimens gained a relatively high strength exceeding 10 MPa at an early age, achieving the targeted 28-day strength. All concrete specimens had higher moduli of elasticity and rupture than the predictions using ACI 318-11 equations, regardless of the curing temperature. The peak temperature rise and the ascending rate of the adiabatic temperature curve measured from the prepared concrete mixes were lower by 12% and 32%, respectively, in average than those of the control specimen made using 80% ordinary Portland cement and 20% conventional fly ash.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.3
• /
• pp.465-469
• /
• 2019

In this paper, the design of BLDC (brushless direct current) motors based on torque and back-EMF equations was carried out to assess the application of the motor in concrete vibrators. The air gap flux density of the motor is an important parameter because the length of the motor and the size of the diameter are given. The air gap magnetic flux density was calculated through a simplified magnetic circuit, and basic design of the shape and dimensions of the motor were then determined by carrying out experiments based on torque, back-EMF, and air magnetic flux density equations. After setting the outer and inner diameters, stack lengths, and rated speed of the motor, a detailed design was performed by simulations using the finite element method by designating the diameter and thickness of the motor as the key parameters. The final design to satisfy the target torque and the lowest THD (Total Harmonic Distortion) was carried out along with a simulation.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.1
• /
• pp.49-55
• /
• 2009

In this study, reduction methods of surface air void were examined for high performance concrete having high viscosity. The effects of assumed influencing factors such as form types, form-coating materials, tamping equipments and methods were examined based on the tests on mock-up specimens made of high performance concrete. The test results can be summarized as follows: As for form types, the most favorable results were obtained when coated plywood form was used with panel-shape tamping equipments at the contact region with concrete, the second and the third being the water/air-permeable sheets and steel with coated plywood, respectively. As for tamping equipments, a vibrator with 6.5cm diameter was most effective. Finally, the shorter the tamping intervals, the better the reduction effect of surface air void. As a conclusion, an improved method was proposed to reduce surface air void and it was verified with the test result that only four air voids as large as $5{\sim}10mm$ are found in the are of $1m^2$.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.509-512
• /
• 2008

The lining concrete of water tunnel is a much capability to occur crack due to drying shrinkage and vibrator compaction etc. Because of crack of concrete induce structural problem and decrease durability of concrete, it is need to reduce crack of concrete. In this an Analytical study to analyze the effect of curing of concrete and compaction on the lining concrete. As the results, it was found that control of construction condition into curing of concrete and compaction improve on construction efficiency of the lining concrete.

• Structural Engineering and Mechanics
• /
• v.39 no.2
• /
• pp.241-266
• /
• 2011

The Self Compacting Concrete, SCC is the new generation type of concrete which is not needed to be compacted by vibrator and it will be compacted by its own weight. Since SCC is a new innovation and also the high strength self compacting concrete, HSSCC behavior is like a brittle material, therefore, understanding the strength effect on the serviceability performance of reinforced self compacting concretes is critical. For this aim, first the normal and high strength self compacting concrete, NSSCC and HSSCC was designed. Then, the serviceability performance of reinforced connections consisting of NSSCC and HSSCC were investigated. Twelve reinforced concrete connections (L = 3 m, b = 0.15 m, h = 0.3 m) were simulated, by this concretes, the maximum and minimum reinforcement ratios ${\rho}$ and ${\rho}^{\prime}$ (percentage of tensile and compressive steel reinforcement) are in accordance with the provision of the ACI-05 for conventional RC structures. This study was limited to the case of bending without axial load, utilizing simple connections loaded at mid span through a stub (b = 0.15 m, h = 0.3 m, L = 0.3 m) to simulate a beam-column connection. During the test, concrete and steel strains, deflections and crack widths were measured at different locations along each member. Based on the experimental readings and observations, the cracked moment of inertia ($I_{cr}$) of members was determined and the results were compared with some selective theoretical methods. Also, the flexural crack widths of the members were measured and the applicability for conventional vibrated concrete, as for ACI, BS and CSA code, was verified for SCCs members tested. A comparison between two Codes (ACI and CSA) for the theoretical values cracking moment is indicate that, irrespective of the concrete strength, for the specimens reported, the prediction values of two codes are almost equale. The experimental cracked moment of inertia $(I_{cr})_{\exp}$ is lower than its theoretical $(I_{cr})_{th}$ values, and therefore theoretically it is overestimated. Also, a general conclusion is that, by increasing the percentage of ${\rho}$, the value of $I_{cr}$ is increased.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.53 no.1
• /
• pp.41-48
• /
• 2017

Encircling gill net fishery is a kind of gill net which is generally used in shallow coastal waters. After the fish have been encircled by the gill net, noise stimulus such as a stone or sound is used to force them to gill or entangle themselves in the netting surrounding them. Although the fishing by a stone is a traditional fishing method, it is considered as an illegal fishing method by physical stimulus such as explosives and mechanical vibrator. However, this illegal fishing method has raised some problems to the fishing boat of other fisheries or many anglers due to disturb aggregating fish schools. This study is aimed to provide scientific base data to verify whether to impact the ecosystem caused by this encircling gill net. This study exhibited that the impulse noise by concrete sphere in the encircling gill net was $159dB/{\mu}Pa$, the ambient noise from ship engine was $160dB/{\mu}Pa$, and the maximum noise from continuous artificial vibrator was $175dB/{\mu}Pa$. These may be stimulus to the escape of fish distributed in a wide area in its natural state; it is not likely the cause of death due to catastrophic stress. Therefore, it needs to prepare the consideration of standard limit on fishing stimulus in fishing methods of the fishery laws and regulations, prevent fishermen form using illegal fishing gear (i.e. explosive sound standards: $200{\sim}220dB/{\mu}Pa$ and provide them with countermeasures.