• Bulletin of the Society of Naval Architects of Korea
• /
• v.4 no.1
• /
• pp.55-58
• /
• 1967

It is investigated that in what shape the stress concentration factor of a notched strip under pure bending changes due to unsymmetrically varying notch angle. Four models made of CR-39, having parameters of r/d-0.225, h/r=4; r/d=0.225, h/r=2; r/d=0.4, h/r=4 and r/d=0.4, h/r=2 respectively as shown in Fig.1, Fig.2 and Table are tested with the use of polariscope. For each model, notch angle is unsymmetrically varied from $0^{\circ}$ to $180^{\circ}$ at intervals of $15^{\circ}$ as shown in Fig. 1 and Fig. 2. The results of this experiment are Fig. 7 and Fig. 8 and the following are deduced. As notch angle increases 1) from $0^{\circ}$ to $50^{\circ}$, the decrement of concentration factor is slight. 2) from $50^{\circ}$ to 90, the decrement of concentration factor is a little steeper. 3) from $30^{\circ}$ to $140^{\circ}$, the decrement of concentration factor is slight. 4) from $140^{\circ}$ to $180^{\circ}$, the decrement is very steep with an abrupt with an abrupt change in the neighborhood of $140^{\circ}$.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.8 no.2
• /
• pp.127-132
• /
• 1984

In this paper, stress concentration factor and distribution of slotted or notched plate which is subjected to uniaxial tensile load are studied. The experimental measurements have shown the following; (1)The stress around slot or notch of slotted or notched plate which is subjected to uniaxial tensile load is state of biaxial stress, which is mainly varied to notch radius and depth. (2)The stress concentration factor around slot or notch is mainly influenced by the .sigma.$_{yy}$ , it is varied with notch radius and depth. (3)For the notched specimen, there is a notch depth where stress concentration factor is maximum. On the other hand, for the slotted specimen, stress concentration factor increases as the notch depth increases. An investigation of the relationship between fracture and stress concentration factor due to the slot or notch will be presented on the later paper, for reference.

• KSBB Journal
• /
• v.8 no.3
• /
• pp.243-255
• /
• 1993

In this study, it was observed that hydrogen Productivity varied with stirrer speed, bead radius, input glucose concentration and dilution rate in a continuous stirred tank reactor in which immobilized R. rubrum KS-301 was used as a hydrogen-producing bacterium The mass transfer resistance due to cell immobilization was also studied. In order to estimate an effectiveness factor, Des of glucose was first obtained, which was subsequently represented by the correlation equation between Dos and Xb, As a result external mass transfer resistance could be neglected for stirrer speeds greater than 400rpn With bead radius increasing, the hydrogen productivity and internal effectiveness factor decreased. With input 91ucose concentration increasing, the hydrogen productivity and interval and external effectiveness factor increased. Although an Internal effectiveness factor was not affected, hydrogen productivity Increased with dilution rate increasing. An overall effectiveness factor remained nearly constant for the dilution rates investigate4 but increased with input 91ucose concentration increasing.

• Architectural research
• /
• v.7 no.1
• /
• pp.19-26
• /
• 2005

Unlike other countries, Korea uses various kinds of wall-paper as finishing material. Conventional wall-paper consists of paper and vinyl, and petrochemical ink is used for the decoration of the surface. Adhesive is used to paste the wall with the wall-paper, which emit substantial amounts of VOCs and formaldehyde. In this study, VOCs characteristics emitted from specimens made of concrete, mortar, gypsum board and wall-paper were investigated using small chamber method. Moreover, concentration and emission factor of BTEX(Benzene, Toluene, Ethylbenzene, m,p,o-Xylene) and TVOC were investigated, and concentration and emission factor decay were estimated. As a result of the prediction, both time-dependent concentration decay and cumulative concentration can be converted into the logarithmic scale. Furthermore, prediction equations were developed from the experimental results under accurately controlled experimental conditions. Therefore, there may be difference if the estimated equations are directly applied to real buildings. Further research should be done on the generalization of the developed prediction equations.

• Journal of Korean Society for Atmospheric Environment
• /
• v.28 no.4
• /
• pp.423-434
• /
• 2012

This study was carried out to develop for the emission factor of greenhouse gas (GHG) from medium and smallscaled incineration facility using RPF which is considering as a part of renewable energy in UNFCC. The actual concentration of the exhaust gas and the fuel composition of RPF were measured for the calculation of GHG emission factor in RPF incinerators, and were compared with the IPCC guideline. The $CO_2$ and $N_2O$ emission factors by the actual concentration of exhaust gas were $2.3575{\pm}1.0070tCO_2/tRPF$ and $0.0014{\pm}0.0014tN_2O/tRPF$ respectively. Also, $CO_2$ emission factor by the RPF composition was $2.7057{\pm}0.0540tCO_2/tRPF$. The GHG emission factor per energy by the actual concentration was $83.0867{\pm}26.0346tCO_2e/TJ$ which showed higher consistency with the GHG emission factor ($80.3967tCO_2e/TJ$) of waste plastic in the IPCC guideline (2006b). The $CO_2$ and $N_2O$ emission factor calculated in this study is considered as a meaningful data for GHG emission factor of RPF incineration facility because of not being developed in ROK.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 1998.03a
• /
• pp.298-303
• /
• 1998

Most of mechanical structures are combined of substructures such as beam and/or plates. There are few system with unibody structures but are not a few systems with united body structures. Generally the dynamic analysis of whole structures is perform ed under alternating load. However, the analysis of each joint area is more important than others for zero severity. This paper presents the results of analysis of concentration stress in bolt jointed structure with variable preload. At frist, a static vibration test was performed to find out a nominal stress of bolt joint ed plates from the relationship between natural frequency and nominal stress. Then a concentration stress was computed at contact point between bolt and plate in the structure. It is believed that the proposed method has promising implications for safer design with fatigue quality index of stress concentration factor and has merit for cost down and saving time at the beginning of vehicle development.

• The Journal of Korean Obstetrics and Gynecology
• /
• v.27 no.1
• /
• pp.1-16
• /
• 2014

Objectives: The purpose of this study was to investigate the effects of Gardeniae Fructus Water Extract (GF) on the production of inflammatory mediators in RAW 264.7 cell treated with lipopolysaccharide (LPS). Methods: Gradeniae Fructus was extracted with distilled water (2,000 ml) for 2 hours. In order to evaluate cytotoxicity of GF, 3 - (4,5-dimethylthiazol-2-yl) - 2,5 - diphenyltetrazolium bromide (MTT) assay was performed. To investigate antiinflammatory effects, the concentration of nitric oxide (NO) was measured with No assay, calcium (Ca) was measured with Fluo-4 Ca assay, and cytokine was measured by Bio-Plex cytokine assay in RAW 264.7 cell. And when p-value is below 0.05, it is judged to have the significant difference statistically. Results: 1. GF did not show any cytotoxicity. 2. GF suppressed the production of NO and Ca at the concentration of 25, 50, 100 and $200{\mu}g/ml$. 3. GF suppressed the production of interleukin (IL)-$1{\beta}$, IL-10, IL-12p40, macrophage-colony stimulating factor (M-CSF), macrophage inflammatory protein (MIP)-$1{\beta}$ and keratinocyte chemoattractant(KC) at the concentration of 25, 50, 100 and $200{\mu}g/ml$. 4. GF suppressed the production of vascular endothelial growth factor (VEGF), granulocyte-colony stimulating factor (G-CSF) and monocyte cheomattractant protein (MCP)-1 at the concentration of 25, 50 and $100{\mu}g/ml$. 5. GF suppressed the production of granulocyte macrophage-colony stimulating factor (GM-CSF) and regulated on activation, normal T cell expressed and secreted (RANTES) at the concentration of 25 and $50{\mu}g/ml$. 6. GF suppressed the production of MIP-2 at the concentration of 50 and $100{\mu}g/ml$, and tumor necrosis factor (TNF)-${\alpha}$ at the concentration of 50 and $200{\mu}g/ml$. Conclusions: These results suggest that GF has anti-inflammatory effect and immuno-modulating activity.

• Journal of the Korean Society for Precision Engineering
• /
• v.25 no.5
• /
• pp.77-81
• /
• 2008

Structural components subjected to high frequency vibrations, such as those used in vibrating parts of gas turbine engines, are usually required to avoid resonance frequencies. Generally, the operating frequency is designed at more than resonance frequencies. When a vibrating structure starts or stops, the structure has to pass through a resonance frequency, which results in large stress concentration. This paper presents the transient thermoelastic stress analysis of vibrating cantilever beam using infrared thermography and finite element method (FEM). In FEM, stress concentration factor at the 2nd resonance vibration mode is calculated by the mode superposition method of ANSYS. In experiment, stress distributions are investigated with infrared thermography and dynamic stress concentration factor is estimated. Experimental result is agreed with FEM result within 10.6%. The advantage of this technique is a better immunity to contact problem and geometric limitation in stress analysis of small or micro structures.

• Membrane Journal
• /
• v.14 no.3
• /
• pp.192-200
• /
• 2004

It is an anaerobic germ that Lactobacillus cell concentrated using ceramic membrane has high stability and long lifetime as compared with polymeric membrane. The effects of operating pressure, temperature, crossflow velocity on cell harvesting have been studied. Also the variation of flux and transmembrane pressure (TMP) with increasing concentration ratio and the change of TMP at constant concentration ratio (volumetric concentration factor: VCF) regarding the optimization have been examined. It showed that the permeate flux increased gradually with the increasing of transmembrane pressure, crossflow velocity, and volumetric concentration factor. The higher initial flux was due to the reduction of viscosity at elevated temperature. However, as operating time progressed, the effect of temperature was negligible since the effect of viscosity became minor. As a result, that operate in a constant concentration ratio, decreased degree could know that become slowly although the flux decreases according as operating time progressed. The flux is a very stable in the condition of constant VCF range. The yield of Latobaciilus (PS 406) which was cultivated at $37^{\circ}C$ was concentrated about 4.9{\times}10^9$ after operation.

• Journal of Industrial Technology
• /
• v.20 no.A
• /
• pp.169-178
• /
• 2000

The 4-point bending tests have been performed In order to estimate the effect of TIG-dressing on fatigue strength and fatigue characteristics quantitatively for non load-carrying fillet welded joints subjected to pure bending. As a result of fatigue tests, fatigue strengths of as-welded specimens have satisfied the grade of fatigue strength prescribed in specifications of korea, AASHTO and JSSC. Fatigue strength at 2 million cycles of TIG-dressing specimens have increased compared with as-welded specimens. As the result of beachmark tests, fatigue cracks occurred at several points, where the radius of curvature and flank angle in the weld bead toes were low, and grew as semi-elliptical cracks, then approached to fracture. As a result of finite element analysis, stress concentration factor in weld bead toes has closely related to the flank angle and radius of curvature, and between these, the radius of curvature has more largely affected in stress concentration factor than flank angle. As a result of fracture mechanics approaches, the crack correction factor of test specimens has largely affected on stress gradient correction factor in case a/t is below 0.4. From the relations between stress intensity factor range estimated from FEM analysis and fatigue crack growth rate, fatigue life has been correctly calculated.