• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.16 no.9
• /
• pp.862-876
• /
• 1991

In this theses, the procedure for finding the equivalent immittance of an n-line coupled structures is presented in terms of the normal mode parameters of the n-line coupled system. The above generalized equations can be applied to the various Coupled structures including directional couplers, DC blocks, bandpass/band elimination filters, and various other uniformly coupled filters. The design equations are based on a simplified TEM(Quasi TEM) mode. The obtained results and the definition of the scattering parameters for a general coupled line four port with arbitrary terminations are used to present the procedure to determine the optimum physical dimensions matching the given load impedances connected to input, output port. Multiple coupled rnicrostrip two-port with three lines circuit designed shows little discrepancy between the conventional method and this one. Four port with five lines were fabricated on teflon substrate($e$r=2.55) with its thickness h=l.588mm designed at the center frequency, 4 GHz. Their measured results are fairly close to the ones by computation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.29 no.12A
• /
• pp.1340-1348
• /
• 2004

In this paper, we propose a PAPR-minimized sequence mapping scheme that achieves the minimum Peak-to-Average Power Ratio (PAPR) and the minimum amount of computations for the OFDM system. To reduce the PAPR, the mapping table is created with information about block index and symbol patterns of the lower signal power. When the input data sequence comes, it performed division by the block length to find the quotient and remainder. The symbol pattern of the lower signal power can be found in terms of the block index as the quotient in the mapping table and transmitted with remainder as the side information to distinguish and recover the original data sequence in the receiver. The two methods with the proposed mapping scheme are proposed in this paper. One is with mapping table to recover the O%M signal in both transmitter and receiver. The other is with mapping table only in transmitter to reduce the load and the complexity in the mobile system. We show that this algorithm provides the PAPR reduction, the simple processing and less computational complexity to be implemented for the multi-carrier system.

• Journal of Communications and Networks
• /
• v.14 no.4
• /
• pp.434-442
• /
• 2012

Several gateway selection schemes have been proposed that select gateway nodes based on a single Quality of Service (QoS) path parameter, for instance path availability period, link capacity or end-to-end delay, etc. or on multiple non-QoS parameters, for instance the combination of gateway node speed, residual energy, and number of hops, for Mobile Ad hoc NETworks (MANETs). Each scheme just focuses on the ment of improve only a single network performance, i.e., network throughput, packet delivery ratio, end-to-end delay, or packet drop ratio. However, none of these schemes improves the overall network performance because they focus on a single QoS path parameter or on set of non-QoS parameters. To improve the overall network performance, it is necessary to select a gateway with stable path, a path with themaximum residual load capacity and the minimum latency. In this paper, we propose a gateway selection scheme that considers multiple QoS path parameters such as path availability period, available capacity and latency, to select a potential gateway node. We improve the path availability computation accuracy, we introduce a feedback system to updated path dynamics to the traffic source node and we propose an efficient method to propagate QoS parameters in our scheme. Computer simulations show that our gateway selection scheme improves throughput and packet delivery ratio with less per node energy consumption. It also improves the end-to-end delay compared to single QoS path parameter gateway selection schemes. In addition, we simulate the proposed scheme by considering weighting factors to gateway selection parameters and results show that the weighting factors improve the throughput and end-to-end delay compared to the conventional schemes.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.8 s.239
• /
• pp.948-955
• /
• 2005

A three-dimensional computation was conducted to understand effects of the inlet boundary layer thickness on the internal flow in a low-speed axial compressor operating at the design condition($\phi=85\%$) and near stall condition($\phi=65\%$). At the design condition, the flows in the axial compressor show, independent of the inlet boundary layer thickness, similar characteristics such as the pressure distribution, size of the hub comer-stall, tip leakage flow trajectory, limiting streamlines on the blade suction surface, etc. However, as the load is increased, the hub corner-stall grows to make a large separation region at the junction of the hub and suction surface for the inlet condition with thick boundary layers at the hub and casing. Moreover, the tip leakage flow is more vortical than that observed in case of the thin inlet boundary layer and has the critical point where the trajectory of the tip leakage flow is abruptly turned into the downstream. For the inlet condition with thin boundary layers, the hub corner-stall is diminished so it is indistinguishable from the wake. The tip leakage flow leans to the leading edge more than at the design condition but has no critical point. In addition to these, the severe reverse flow, induced by both boundary layer on the blade surface and the tip leakage flow, can be found to act as the blockage of flows near the casing, resulting in heavy loss.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.45 no.4
• /
• pp.84-91
• /
• 2008

This paper suggests the robust localization system in the application of ambient display with multiple ultrasonic range sensors. The ambient display provides the interactive image and video to improve the quality of life, especially for low mobility elders. Due to the limitation of indoor localization, this paper employs linear prediction algorithm to recover the missing information based on AR(Autoregressive) model by using Yule-Walker method. Numerous speculations from prediction error and computation load are considered to decide the optimal length of referred data and order. The results of these analyses demonstrate that the linear prediction algorithm with the 16th order and 50 reference data can improve reliability of the system in average 74.39% up to 97.97% to meet the performance of interactive system.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2003.11a
• /
• pp.73-78
• /
• 2003

In this research, we implement Realtime Air Diffusion Prediction System which is a parallel Fortran model running on distributed-memory parallel computers. The system is designed for air diffusion simulations with four-dimensional data assimilation. For regional air quality forecasting a series of dynamic downscaling technique is adopted using the NCAR/Penn. State MM5 model which is an atmospheric model. The realtime initial data have been provided daily from the KMA (Korean Meteorological Administration) global spectral model output. It takes huge resources of computation to get 24 hour air quality forecast with this four step dynamic downscaling (27km, 9km, 3km, and lkm). Parallel implementation of the realtime system is imperative to achieve increased throughput since the realtime system have to be performed which correct timing behavior and the sequential code requires a large amount of CPU time for typical simulations. The parallel system uses MPI (Message Passing Interface), a standard library to support high-level routines for message passing. We validate the parallel model by comparing it with the sequential model. For realtime running, we implement a cluster computer which is a distributed-memory parallel computer that links high-performance PCs with high-speed interconnection networks. We use 32 2-CPU nodes and a Myrinet network for the cluster. Since cluster computers more cost effective than conventional distributed parallel computers, we can build a dedicated realtime computer. The system also includes web based Gill (Graphic User Interface) for convenient system management and performance monitoring so that end-users can restart the system easily when the system faults. Performance of the parallel model is analyzed by comparing its execution time with the sequential model, and by calculating communication overhead and load imbalance, which are common problems in parallel processing. Performance analysis is carried out on our cluster which has 32 2-CPU nodes.

• Journal of Korea Game Society
• /
• v.7 no.3
• /
• pp.59-66
• /
• 2007

Ray tracing is one of the classical global illumination methods to generate a photo-realistic rendering image with various lighting effects such as reflection and refraction. However, there are some restrictions on real-time applications because of its computation load. In order to overcome these limitations, many researches of the ray tracing based on GPU (Graphics Processing Unit) have been presented up to now. In this paper, we implement the ray tracing algorithm by J. Purcell and combine it with two methods in order to improve the rendering performance for interactive applications. First, intersection points of the primary ray are determined efficiently using rasterization on graphics hardware. We then construct the acceleration structure of 3D objects to improve the rendering performance. There are few researches on a detail analysis of improved performance by these considerations in ray tracing rendering. We compare the rendering system with environment mapping based on GPU and implement the wireless remote rendering system. This system is useful for interactive applications such as the realtime composition, augmented reality and virtual reality.

• Advances in concrete construction
• /
• v.9 no.4
• /
• pp.355-365
• /
• 2020

The influence of temperature on the material of concrete filled columns (CFCs) under axial loading has been quantitatively studied in this research. CFCs have many various advantages and disadvantages. One of the important inefficiency of classic CFCs design is the practical lack of hooped compression under the operational loads because of the fewer variables of Poisson's rate of concrete compared to steel. This is the reason why the holder tends to break away from the concrete core in elastic stage. It is also suggested to produce concrete filled steel tube columns with an initial compressed concrete core to surpass their design. Elevated temperatures have essentially reduced the strengths of steel tubes and the final capacity of CFCs exposed to fire. Thus, the computation of bearing capacity of concrete filled steel tube columns is studied here. Sometimes, the structures of concrete could be exposed to the high temperatures during altered times, accordingly, outcomes have shown a decrement in compressive-strength, then an increase with the reduction of this content. In addition, the moisture content at the minimal strength is declined with temperature rising. According to Finite Element (FE), the column performance assessment is carried out according to the axial load carrying capacities and the improvement of ductility and strength because of limitations. Self-stress could significantly develop the ultimate stiffness and capacity of concrete columns. In addition, the design equations for the ultimate capacity of concrete columns have been offered and the predictions satisfactorily agree with the numerical results. The proposed based model (FE model of PEC column) 65% aligns with the concrete exposed to high temperature. Therefore, computed solutions have represented a better perception of structural and thermal responses of CFC in fire.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.4_1
• /
• pp.67-76
• /
• 1992

A hierarchical formulation based on p-version of the finite element method for linear elastic axisymmetric stress analysis is presented. This is accomplished by introducing additional nodal variables in the element displacement approximation on the basis of integrals of Legendre polynomials. Since the displacement approximation is hierarchical, the resulting element stiffness matrix and equivalent nodal load vectors are hierarchical also. The merits of the propoosed element are as follow: i) improved conditioning, ii) ease of joining finite elements of different polynomial order, and iii) utilizing previous solutions and computation when attempting a refinement. Numerical examples are presented to demonstrate the accuracy, efficiency, modeling convenience, robustness and overall superiority of the present formulation. The results obtained from the present formulation are also compared with those available in the literature as well as with the analytical solutions.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.20 no.1
• /
• pp.30-35
• /
• 2010

This paper presents a quality enhancement of images by using a histogram equalization based on the symmetric logistic function. The histogram equalization is a simple and effective spatial processing method that it enhances the quality by adjusting the brightness of image. The logistic function that is a sigmoidal nonlinear transformation function, is applied to non-linearly enhance the brightness of the image according to its intensity level frequency. We propose a flexible and symmetrical logistic function by only using the intensity with maximum frequency in an histogram and the total number of pixels. The proposed function decreases the computation load of an exponential function in the traditional logistic function. The proposed method has been applied for equalizing 5 images with a different resolution and histogram distribution. The experimental results show that the proposed method has the superior enhancement performances compared with the source images and the traditional global histogram equalization, respectively.