• The Korean Journal of Food And Nutrition
• /
• v.9 no.4
• /
• pp.466-471
• /
• 1996

In order to investigate the compression characteristics on the some vegetables-cucumber, garlic, ginger, potato, and radish-compression force, distance, and time were measured with a Struct-O-Graph and correlations between them were investigated. Force-distance and distance-time curves were showed simply and reflection points were showed rarely. The time to rupture point was long of 11.7sec at the compression speed of 60mm/min and of 6.16sec at the compression speed of 120mm/min in potato, and short of 9.65, 4.55sec at the different compression speed in garlic, respectively. The rupture force was large of 16.64~20.00N at the different compression speed in potato and radish, and the sample at rupture point was showed crushing behavior under probe. These phenomena were suggested because compression strength of sample was different. In the result of regression analysis for force-time and distance-time to the rupture point, the correlation coefficients were above 0.96, and difference of among samples was small. The slopes of force-time were large of 1.772~3.385 in cucumber and small of 1.743~3.338 in potato, and the slopes of distance-time were obtained with reverse results.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.321-321
• /
• 2009

This paper presents quasi-zero-stiffness (QZS) characteristic of a passive isolator using flexures under compression force. The passive isolator consists of a positive stiffness element (a vertical coil spring) and a negative stiffness element (flexures under compression force), and their proper combination of the positive and negative stiffness elements can produce both substantial static and zero dynamic stiffness, so called QZS. Firstly, a nonlinear dimensionless expression of a flexure under compression force is derived. A dynamic model of the passive isolator is developed and numerical simulations of its time and frequency response are performed. Then, undesirable nonlinear vibration is quantified using a period doubling bifurcation diagram and a Poincare's map of the isolator under forced excitation. Finally, experiments are performed to validate the QZS characteristic of the passive isolator.

• Proceedings of the KSME Conference
• /
• 2001.11a
• /
• pp.149-154
• /
• 2001

In case of high capacity load force as millions of tons, it is difficult to measure the force with load cell. But we can measure and calculate the force with applied pressure and ram area of hydraulic jack. The 5,200 ton compression load tester is composed of thirteen hydraulic jack with 400 ton capacity. This paper explains the method of measuring the vertical compression load and provides characteristics of unit jack, and displacement of upper structure under maximum load condition.

• Structural Engineering and Mechanics
• /
• v.52 no.4
• /
• pp.687-699
• /
• 2014

Based on the energy method considering the second order effects, the natural frequencies of externally prestressed simply supported beam and the compression softening effect of external prestress force were analyzed. It is concluded that the compression softening effect depends on the loss of external tendon eccentricity. As the number of deviators increases from zero to a large number, the compression softening effect of external prestress force decreases from the effect of axial compression to almost zero, which is consistent with the conclusion mathematically rigorously proven. The frequencies calculated by the energy method conform well to the frequencies by FEM which can simulate the frictionless slide between the external tendon and deviator, the accuracy of the energy method is validated. The calculation results show that the compression softening effect of external prestress force is negligible for the beam with 2 or more deviators due to slight loss of external tendon eccentricity. As the eccentricity and area of tendon increase, the first natural frequency of the simply supported beams noticeably increases, however the effect of the external tendon on other frequencies is negligible.

• Structural Engineering and Mechanics
• /
• v.81 no.4
• /
• pp.481-492
• /
• 2022

Cycloidal ball planetary transmission (CBPT) has many applications as precision reducer, such as precision machinery and automation drive systems etc. The traditional analytical model of CBPT cannot accurately describe the change of the normal force of meshing points, and thus cannot describe the precise transmission process of meshing pairs. In the paper, a method for deriving the normal force equation is put forward by using the non-linear relationship between force and deformation in elastic mechanics. The two-point contact analytical models of all the meshing pairs are established to obtain the micro-displacement analytical model of CBPT under axial pre-tightening. Then, the non-real-time two-point contact analytical models of all the meshing pairs are further constructed to obtain the normal force expression to determine the critical compression coefficients. Experimental investigations are performed to verify the analytical model using the critical compression coefficients.

• Steel and Composite Structures
• /
• v.21 no.2
• /
• pp.357-371
• /
• 2016

Column base connections are critical components in steel structures because they transfer axial forces, shear forces and moments to the foundation. Exposed column bases are quite commonly used in low- to medium-rise buildings. To investigate shear transfer in exposed column base plates, four large scale specimens were subjected to a combination of axial load (compression or tension) and lateral shear deformations. The main parameters examined experimentally include the number of anchor rod, arrangement of anchor rod, type of lateral loading, and axial force ratio. It is observed that the shear resisting mechanism of exposed column base changed as the axial force changed. When the axial force is in compression, the resisting mechanism is rotation type, and the shear force will be resisted by friction force between base plate and mortar layer. The specimens could sustain inelastic deformation with minimal strength deterioration up to column rotation angle of 3%. The moment resistance and energy dissipation will be increased as the number of anchor rods increased. Moreover, moment resistance could be further increased if the anchor rods were arranged in details. When the axial force is in tension, the resisting mechanism is slip type, and the shear force will be resisted by the anchor rods. And the shear resistance was reduced significantly when the axial force was changed from compression to tension. The test results indicated that the current design approach could estimate the moment resistance within reasonable acceptance, but overestimate the shear resistance of exposed column base.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.30 no.5
• /
• pp.368-379
• /
• 2004

Distraction osteogenesis is a biologic process of new bone formation between the surfaces of bone segments that are gradually separated by incremental traction. Distraction osteogenesis is clinically applied as a new treatment modality of mandibular hypoplasia or bony defect area in maxillofacial area by many studies of distraction devices and method. But disadvantage of distraction osteogenesis shows unfavorably long consolidation period and relapse tendency. Therefore. this experiment was designed to investigate the effectiveness of combined application of distraction and compression force for improving of bone quality and shortening of treatment period during distraction osteogenesis. Twenty-one Sprague-Dawley rats with $300{\sim}350gm$ were used. These were divided into two group as distraction group and combination group was applied with compression force in the consolidation period. The rat were sacrificed for gross finding, radiographic and histologic findings. at 2, 4 weeks after distraction. The result were follow : 1. On radiographic finding, all experimental groups appeared more radiopacity than control groups both at 2, 4 weeks after distraction. 2. On histologic finding, trabeculae of bone and mature lamellar bone were showed increasingly in experimental group. Ossification occured rapidly. From this study, we may suggest that compression force application in consolidation period during distraction osteogenesis can be useful method improve bone quality and to shorten the treatment period. But more experimental and clinical studis are necessitated on effects of compression force application during distraction osteogenesis.

• The korean journal of orthodontics
• /
• v.11 no.1
• /
• pp.17-23
• /
• 1981

This experiment was performed to investigate the response of inorganic substances in alveolar bone in relation to the experimental tooth movement. Right canine in maxillary jaw was tipped in cats by coil springs generating 80 gm. force, in mandibular jaw, the force was 100 gm. force. Cats were divided into five groups and orthodontically treated for one hour, 1, 7, 14 and 28 days, respectively. Alveolar bone samples were obtained from tension and compression sites as well as from contralateral control sites. The level of calcium of alveolar bone was determined by atomic absorption spectrophotometry and inorganic phosphorus was measured by spectrophotometry. The results obtained were as follows: 1. In tension and compression site of maxillary alveolar bone, calcium levels were decreased at 1, 7 and 14 days, but recovered at 28 days. 2. The levels of inorganic phosphorus in compression site of maxillary alveolar bone had little change but in tension site of maxillary alveolar bone , phosphorous levels were decreased, 3. Calcium levels in tension and compression site of mandibular alveolar bone were decreased, especially at 28 days. 4. In tension and compression site of mandibular alveolar bone, inorganic phosphorus were slightly decreased from 1 day.

• Journal of Biosystems Engineering
• /
• v.21 no.1
• /
• pp.52-59
• /
• 1996

In this study, the combined forces of electro-osmosis and compression were applied to cabbage dewatering and their effects were discussed. Nine treatments of combined forces consisting of three levels of voltage and compression were applied to chopped and macerated chinese cabbage placed in the experimental set-up consisted of cylinder-piston. The results showed that as both voltage and pressure increased the dewatering rates increased and the combined force of voltage and compression was a very effective means in the dewatering of chinese cabbage in which the largest dewatering rate difference, 72%, was found between the combined force of 30V with 68.2kPa and no voltage(0V) with 68.2kPa. However, no significant difference was found between the voltage of 0 and 10volts in 9.75kPa and the pressure of 68.2kP and 126.7kPa in 30volts. The maximum and minimum dewatering rate were 82% in the combined force of 30 volts of 126.7kPa and 8% in 0 volt of 9.75kPa, respectively. Within the experimental trials, it appeared that the best treatment combination would be pressure of 68.2kPa and voltage of 30V producing dewatering rate of 80ft in which the produced liquid contained about 1% solid. Employing this dewatering method as a pretreatment before drying process can contribute in considerable energy saving in agricultural wastes treatment.

• Polymer(Korea)
• /
• v.38 no.2
• /
• pp.193-198
• /
• 2014

Lens and DVD require high quality of optical property. Conventional injection molded products contain high residual stress and this invokes birefringence since high cavity pressure and high temperature variation are involved in a molding process. Thus these products are often molded by injection compression molding in order to minimize the residual stress through reducing cavity pressure and uniform cavity pressure. In this study, molding parameters affecting molding quality such as property uniformity in injection compression molding were investigated through experiment. Molding quality deviations among the cavities in multi-cavity mold were also studied. Transparent resins, PC and PS were used in this study. Compression gap, compression speed, compression force, and compression delay time for processing variables in injection compression molding were applied in experiment. Compression force, compression delay time, and compression gap significantly affected the optical property of product. The degree of influence of process variable on the product quality was different in different resins. This implies that the optimal operational conditions in injection compression molding existed for each resin according to flow property.