• Journal of electromagnetic engineering and science
• /
• v.7 no.3
• /
• pp.138-146
• /
• 2007

In this paper, a monopole antenna of conical-cylindrical compound shape is presented. The conventional circular conical monopole antenna is modified by placing a cylinder at the top of the inverted cone. The cylindrical portion is useful in the wide band impedance matching, in adjusting the antenna gain in the horizontal direction, and in reducing the cone diameter. The dependence of the antenna performance on various geometric parameters is investigated using a commercial electromagnetic simulation software, from which an optimum design of the antenna is derived. The diameter of the circular ground plane is minimized to 115 wavelength at the lowest operating frequency. The antenna proposed in this study shows a reflection coefficient less than -10 dB and a 1${\sim}$6 dBi gain over 3${\sim}$20 GHz frequencies. The antenna shows a circular-symmetric radiation pattern in the horizontal plane and a null-free pattern in the vertical direction over the whole operating frequency range.

• Tribology and Lubricants
• /
• v.16 no.3
• /
• pp.223-230
• /
• 2000

Factors influencing friction reduction with MODTP(molybdenum dialkyl dithiophosphate) lubricant were investigated through a frictioning experiment using two-cylinder edge surface frictioning tester and XPS surface analysis. The friction reduction effect gained with MoDTP lubricant appeared to be largely attributable to MoS$_2$ formation on the frictioning interface. Under N$_2$ atmosphere, Mo diffused into the metal substrate, easily escaping from MoS$_2$ so the friction reduction effect from MoDTP was not gained. However, when an oxide surface film was preliminary prepared on frictioning surface, this Mo diffusion to metal substrate from MoS$_2$ was effectively inhibited. Then desired lubulication effect of MoDTP was gained even under N$_2$atmosphere. As such, the existence of a surface oxide film on the frictioning surface was concluded to be of essential importance in order to gain a lubrcating effect with MoDTP.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.4D
• /
• pp.555-561
• /
• 2009

In lieu of section profile data, a fitting of the bored tunnel shape is more significant confirmation for maintenance of a tunnel. Before the permit on the completion of a tunnel, deformation of the completed tunnel with respect to the design model are considered. And deformation can be produced at continuously along the entire of the tunnel section. This study firstly includes an analysis of algebraic approach and test it with an observed field data. And then a number of methods, line search method, genetic algorithm, and pattern search methods, are compared with the 3D tunnel shape fitting. Algebraic methods can solve a simple circular cylinder type as like a railway tunnel. However, a more complex model (compound circular curve and non circular) as like a highway tunnel has to be solved with soft computing tools in the cause of conditional constraints. The genetic algorithm and pattern search methods are computationally more intensive, but they are more flexible at a complex condition. The line search method is fastest, but it needs a narrow bounds of the initial values.

• Journal of Korean Ophthalmic Optics Society
• /
• v.13 no.1
• /
• pp.125-129
• /
• 2008

Purpose: To research the study of abnormal refraction eye on women population of university students in South - East Korea. Methods: Between March 2007 and October 2007, the refraction test of eye glasses wearer was evaluated on women population (367 students, aged 19~22 years) of university in living on Kyung-Nam and Pusan province. Data was analysed with T-test. Results: On the abnormal refraction status, Compound Myopic Astigmatism was 76.72%, simple myopia was 10.90%, mixed astigmatism was 6.27%, respectively. On the prevalence of myopic power, low was 59.57%, moderate was 24.93%, high was 15.49%, respectively. On the myopic equivalent power, the right eye had more increase to compare to left eye. but these was not a statically significant correlation (p<0.5) between the right and left eyes. On the anisometropia of spherical equivalents and cylinder power, most subjects was under 1.0 diopter. On the other hand, the type of astigmatic axis was with-the rule (70.79%), against -the rule (18.41%), and oblique (10.80%). Conclusions: This study identify that the refraction status of abnormal refraction eye on women population in university students in South-East Korea have been more increased prevalence the myopia and astigmatism.

• Journal of the Korean Society of Costume
• /
• v.63 no.2
• /
• pp.29-44
• /
• 2013

This study is about the periodic characteristics of Wonsam in the Joseon Dynasty. Wonsam include the Danryeong-shaped Wonsam in the beginning, the compound Wonsam in a period of transition and the stereotyped Wonsam in the late Joseon Dynasty. The formative characteristics of Wonsam are divided into four stages. The first stage of the Wonsam is from the 15th to 16th century. The shape of Wonsam began to form and it was similar to one of Danryeong during this time. The formative characteristics of the first Wonsam included collars that looked like one of Danryeong, side pleats(called Moo) with multiple inner folds, straight cylinder-shaped sleeves, and a belt tied with the Wonsam. There were various fabrics that were used for the Wonsam from this stage. Second stage of the Wonsam is from the early 17th to mid 17th century. This period marked the beginning of the transition of the Wonsam and it served as a stepping-stone to the development stage in the Joseon Dynasty. The characteristics of the transitional Wonsam were a complex combination of the Danryeong and Wonsam. During this period, the Wonsam went through many changes and forms in a short period of time. Third stage of the Wonsam is from the mid 17th to early 19th century. The Wonsam was developed at this stage. The developed Wonsam went through a period of transition equipped with a stable form. The formative characteristics of Wonsam during this period included collars that faced each other, big and wide sleeves with multicolored stripes, Hansam, curve-edged side seam and the side pleats(Moo) with multiple inner folds had disappeared. It was a turning point from the single-layered clothes to double layered clothes and from dark blue to green color appeared at this time. The fabric patterns of this stage tended to consist of more simplified silk pattern. The fourth stage of the Wonsam is from the late 19th to 20th century. The Wonsam was expanded at this stage. The formative characteristics and fabrics were typically used for the standard Wonsam and were divided into two types; as a ceremonial robe used in courts and a wedding ceremonial robe for the common people. Phenomena such as sewing of double-layered clothes as one and straight-edged side seam during the late Joseon period developed into simpler and more practical fashion culture.

• Journal of Energy Engineering
• /
• v.25 no.4
• /
• pp.13-29
• /
• 2016

In this study, we analyzed the causes of major faults in the biogas plant through the case of gas engine failure when cogenerating electricity and heat using biogas as a fuel in the actual sewage treatment plant and suggested countermeasures. Hydrogen sulfide in the biogas entering the biogas engine and water caused by intermittent malfunction of the water removal system caused intercooler corrosion in the biogas engine. In addition, the siloxane in the biogas forms a silicate compound with silicon dioxide, which causes scratches and wear of the piston surface and the inner wall of the cylinder liner. The substances attached to the combustion chamber and the exhaust system were analyzed to be combined with hydrogen sulfide and other impurities. It is believed that hydrogen sulfide was supplied to the desulfurization plant for a long period of time because of the high content of hydrogen sulfide (more than 50ppm) in the biogas and the hydrogen sulfide was introduced into the engine due to the decrease of the removal efficiency due to the breakthrough point of the activated carbon in the desulfurization plant. In addition, the hydrogen sulfide degrades the function of the activated carbon for siloxane removal of the adsorption column, which is considered to be caused by the introduction of unremoved siloxane waste into the engine, resulting in various types of engine failure. Therefore, hydrogen sulfide, siloxane, and water can be regarded as the main causes of the failure of the biogas engine. Among them, hydrogen sulfide reacts with other materials causing failure and can be regarded as a substance having a great influence on the pretreatment process. As a result, optimization of $H_2S$ removal method seems to be an essential measure for stable operation of the biogas engine.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.12 no.3
• /
• pp.143-150
• /
• 2009

Fuel oil mostly used for a ship is made from crude oil by refining process. In order to produce plenty of high-quality fuel oil, the Fluid catalytic cracking(FCC) method is widely adopted to many refinery factories during the decomposition process from high molecule into lower molecule. The major constituents in spent FCC catalysts are Si, Al, Fe, Ti, alkali metals and some others. The spent catalyst is also composed small amounts of rare metals such as Ce, Nd, Ni and V. The big problem in FCC oil is mixing the catalyst in the oil. This reason is unstable separation of FCC catalyst in separator. Such a FCC catalyst will become a reason of heavy wear down in moving parts of engine. The impurity in oil is ash and deposit compound, such as Al, Si, Ni, Fe and V, which will accelerate the wear down on fuel pump, fuel injection valve cylinder liner and piston ring. It is important to find a basic reason of an engine trouble for preventing similar troubles anymore. Insurance compensation will be different according to the reason of an engine trouble which might be natural abrasion or other external causes. In this study, types and reasons of engine troubles related to fuel oil will be covered.

• Advances in nano research
• /
• v.13 no.6
• /
• pp.575-585
• /
• 2022

Due to its biofilm formation and colonization of the osteocyte-lacuno canalicular network (OLCN), Staphylococcus aureus (S.aureus) implant-associated bone infection (SIABI) is difficult to cure thoroughly, and may occur recurrently subsequently after a long period dormant. It is essential to explore an alternative therapeutic strategy that can eradicate the pathogens in the infected foci. To address this, the polymethylmethacrylate (PMMA) bone cement and Fe3O4 nanoparticles compound cylinder were developed as implants based on their size and mechanical properties for the alternative magnetic field (AMF) induced thermal ablation, The PMMA mixed with optimized 2% Fe₃O₄ nanoparticles showed an excellent antibacterial efficacy in vitro. It was evaluated by the CFU, CT scan and histopathological staining on a rabbit 1-stage transtibial screw model. The results showed that on week 7, the CFU of infected soft tissue and implants, and the white blood cells (WBCs) of the PMMA+2% Fe₃O₄+AMF group decreased significantly from their controls (p<0.05). PMMA+2% Fe₃O₄+AMF group did not observe bone resorption, periosteal reaction, and infectious reactive bone formation by CT images. Further histopathological H&E and Gram Staining confirmed there was no obvious inflammatory cell infiltration, neither pathogens residue nor noticeably burn damage around the infected screw channel in the PMMA+2% Fe₃O₄+AMF group. Further investigation of nanoparticle distributions in bone marrow medullary and vital organs of heart, liver, spleen, lung, and kidney. There were no significantly extra Fe₃O₄ nanoparticles were observed in the medullary cavity and all vital organs either. In the current study, PMMA+2% Fe₃O₄+AMF shows promising therapeutic potential for SIABI by providing excellent mechanical support, and promising efficacy of eradicating the residual pathogenic bacteria in bone infected lesions.

• The korean journal of orthodontics
• /
• v.34 no.4 s.105
• /
• pp.325-332
• /
• 2004

A self-etching primer that combines the etchant and primer in one chemical compound saves time and should be mote cost-effective to the clinician and patient. The purpose of this study was to evaluate the clinical effectiveness of a self-etching primer by measuring shear bond strengths according to various conditions and observing adhesive failure patterns. For this Investigation, 120 upper and lower premolars extracted for orthodontic purposes were used and randomly divided into six groups of twenty teeth each. Human premolars were embedded in a metal cylinder with orthodontic resin. Metal brackets and ceramic brackets were bonded with XT primer and self-etching primer by means of XT adhesive. Upon curing, plasma arc light and visible light were used. After bonding, the shear bond strength was tested by Instron universal testing machine, and the amount of residual adhesive that remained on the tooth after debonding was measured by stereoscope and assessed with an adhesive remnant index. The results were as fellows: 1. When brackets were bonded, if other conditions remained the same, there was no significant difference in shear bond strength due to the type of primer - either self-etching primer or XT primer. 2. When metal brackets were bonded, there was no significant difference in shear bond strength according to the source of light - plasma arc light or visible light - and type of primer. 3. There was a very significant difference in shear bond strength according to the type of brackets - metal or ceramic brackets. The shear bond strength of ceramic brackets was stronger than metal brackets. 4. When the adhesive failure patterns of metal brackets bonded with self-etching primer were observed by using the adhesive remnant index, the bond failure of the metal bracket occurred more frequently at the bracket-adhesive. The failure of the ceramic bracket, however, occurred more frequently at the enamel-adhesive interface. The adhesive failure patterns of metal brackets bonded with XT primer observed the same patterns. The above results suggest that self-etching primer can be clinically useful for bonding the brackets without fear of a decrease in shear bond strength.