• Journal of the Korean Society for Heat Treatment
• /
• v.19 no.1
• /
• pp.30-36
• /
• 2006

Fretting fatigue behavior of SCM420 steel commonly used in the automotive industry for structural applications was investigated in this study. In addition, the effect of bridge pad on the fretting fatigue test was evaluated from different pad materials and following conclusions were drawn. Simple fatigue limit of SCM 420 steel was determined to be 350 MPa while this value was 225 MPa and 285.5 MPa with SCM420H and with SM45C pad, respectively. Reduction in fatigue limit was, thus found to be 35.7% and 17.9% with SCM 420H pad and SM45C pad, respectively. Results of fracture surface observation revealed that typical striation pattern of fatigue failure existed as well as dimpled and cleavage frature appearance was found in final fractured region. From the EDS compositional analysis, test sample and pad part all had high signals for oxygen and iron, suggesting that worn particles might be iron oxide, although exact chemical composition has to be confirmed. Considerable reduction in fatigue life was apparent in SCM 420 steel under fretting fatigue against simple fatigue. Such reduced fatigue life by fretting damage should be considered as an important factor not only in the viewpoint of repairing but also inevitably in the design stage of structural components.

• 한국연소학회:학술대회논문집
• /
• 2005.10a
• /
• pp.328-336
• /
• 2005

Effects of surface defect distribution on flame instability during flame-surface interaction are experimentally investigated. To examine the chemical quenching phenomenon, we prepared thermally grown silicon oxide plates with well-defined defect density. Ion implantation was used to control the number of defects, i.e. oxygen vacancies. In an attempt to preferentially remove the oxygen atoms from silicon dioxide surface, argon ions with low energy level from 3keV to 5keV were irradiated at the incident angle of $60^{\circ}C$. Compositional and structural modification of $SiO_2$ induced by low-energy $Ar^+$ ion irradiation has been characterized by Atomic Force Microscopy (AFM) and X-ray Photoelectron Spectroscopy (XPS). The analysis shows that as the ion energy increases, the number of structural defect also increases and non-stoichiometric condition of $SiO_x(x{\le}2)$ plates is enhanced. From the quenching distance measurements, we found out that when the surface temperature is under $300^{\circ}C$, the quenching distance decreases on account of reduced heat loss; as the surface temperature increases over $300^{\circ}C$, however, quenching distance increases despite reduced heat loss effect. Such aberrant behavior is caused by heterogeneous chemical reaction between active radicals and surface defect sites. The higher defect density, the larger quenching distance. This results means that chemical quenching is governed by radical adsorption and can be parameterized by the oxygen vacancy density on the surface.

• Corrosion Science and Technology
• /
• v.3 no.3
• /
• pp.112-117
• /
• 2004

This work investigated the material properties of Ni-P-B alloy electrodeposits obtained from a Ni sulfamate bath as a function of the contents of the P and B sources($H_3PO_3$ and dimethyl amine borane complex(DMAB), respectively) with/without additives. Chemical composition, residual stress, microstructure and micro hardness were investigated using ICP(inductively coupled plasma) mass spectrometer, flexible strip, XRD, TEM and micro Vickers hardness tester, respectively. From the results of the compositional analysis, it was observed that P and B are incorporated competitively during the electrodeposition and the sulfur from the additive is codeposited into the electrodeposit. The measured residual stress value increased in the order of Ni, Ni-P, Ni-B and Ni-P-B electrodeposits indicating that boron affects the residual tensile stress greater than phosphorus. As the contents of the alloying element sources of P and B increased, crystallinity and the grain size of the electrodeposit decreased. The effect of boron on crystallinity and grain size was also relatively larger than the phosphorus. It can be explained that the boron with a smaller atomic radius contributes to the increase of residual stress in the tensile direction and the larger restraining force against the grain growth more significantly than the phosphorus with a larger atomic radius. Introduction of an additive into the bath retarded crystallization and grain growth, which may be attributed to the change of the grain growth kinetics induced by the additive adsorbed on the substrate and electrodeposit surfaces during electrodeposition.

• Food Science of Animal Resources
• /
• v.31 no.5
• /
• pp.668-675
• /
• 2011

The effects of adding goldenrod leaf (GL) and stem powder (GS) (1 and 2%) to sausage meat were evaluated for quality characteristics. The compositional properties, pH, cooking yield, instrumental color, emulsion stability, viscosity, texture, and sensory properties were investigated. Adding GL and GS increased the moisture and ash concentration in sausages. Furthermore, increasing the amount of added GL and GS helped to develop (p<0.05) cooking yield, emulsion stability, and viscosity in the meat batters. Sausages with 2% GL and GS had significantly higher springiness and hardness than those of the control. No significant differences in cohesiveness were observed among the treatments. CIE L*and CIE a*values were highest (p<0.05) in the control sausage. Treatment with 2% GL resulted in the highest CIE b* values (p<0.05) in batter and sausages. No significant difference was observed between the control and other treatments for the overall acceptability. Overall, this study indicated that GL and GS could be used as dietary fiber in sausages to improve quality characteristics.

• The Journal of Korean Academy of Prosthodontics
• /
• v.27 no.2
• /
• pp.219-248
• /
• 1989

The purposes of this study were to analyze the microstructural and compositional changes of metal surfaces following different conditions of preoxidizing heat treatment, to investigate the composition of metal oxides, and to evaluate the effect of preoxidation and removal of surface oxides on microstructure and diffusion profiles. The techniques of EDAX (energy-dispersive analysis of x-ray), ESCA (electron spectroscopy for chemical analysis), and EPMA (electron probe micro analysis) were used, along with SEM (scanning electron microscopy). The obtained results were as follows : 1. A surface of the specimen became rough and the amount of the metal oxides increased with increasing the heat treatment time and temperature and the partial pressure of oxygen. 2. At an air pressure of 28' vacuum, the higher the temperature and the longer the time of preoxidation, the higher Ni concentration was detected. 3. Cr concentration in the specimen heat treated with air was higher than that of with vacuum. 4. The oxides in the specimens were mainly composed of Ni and Cr oxides. On the globular growth particles, significant rises in Al concentration of Rexillium III and Ti concentration of Verabond were noted. 5. Atomic diffusion occurred at the ceramic-metal interface, furthermore the amount of the flux was increased with preoxidation heat treatment.

• Journal of Bio-Environment Control
• /
• v.15 no.1
• /
• pp.91-99
• /
• 2006

This study was conducted to determine the influence of postharvest dipping treatment with aminoethoxyvinylglycine (AVG) on ethylene production and composition of non-cellulosic neutral sugars in cell walls of 'Tsugaru' apple fruits during storage. Fruits were harvested on August 20, soaked in AVG 50 and 75 $mg L^{-1}$ solution for 5 minutes, and stored in cold storage chamber at $0{\pm}1^{\circ}C$ for 60 days. Fruit quality factor, ethylene productions, and cell wall component changes were investigated at 20 days interval. As a result, the fruit firmness and acid content were much higher in AVG treated fruits than those of untreated one during 60 days of cold storage. Ethylene production of AVG treated fruits was reduced to the level of 1/10 compared with untreated one. As to the change of non-cellulosic neutral sugars in the cell walls of 'Tsu- garu' fruits, the major sugar was arabinose and galactose in water, CDTA and $Na_2CO_3$ soluble fractions. The content of arabinose and galactose in untreated fruits increased as the softening of fruits was in progress, but the fruits treated with AVG showed a little change during storage, so it is predicted that these two cell wall compositional sugars were not solubilized by the treatment of AVG. Accordingly, the marketability of 'Tsu- garu' fruits could remarkably increase when soaking the fruits in AVG solution after harvest.

• Korean Journal of Materials Research
• /
• v.23 no.11
• /
• pp.638-642
• /
• 2013

Chalcopyrite $CuInSe_2$(CIS) is considered to be an effective light-absorbing material for thin film photovoltaic solar cells. CIS thin films have been electrodeposited onto Mo coated and ITO glass substrates in potentiostatic mode at room temperature. The deposition mechanism of CIS thin films has been studied using the cyclic voltammetry (CV) technique. A cyclic voltammetric study was performed in unitary Cu, In, and Se systems, binary Cu-Se and In-Se systems, and a ternary Cu-In-Se system. The reduction peaks of the ITO substrate were examined in separate $Cu^{2+}$, $In^{3+}$, and $Se^{4+}$ solutions. Electrodeposition experiments were conducted with varying deposition potentials and electrolyte bath conditions. The morphological and compositional properties of the CIS thin films were examined by field emission scanning electron microscopy (FE-SEM) and energy dispersive spectroscopy (EDS). The surface morphology of as-deposited CIS films exhibits spherical and large-sized clusters. The deposition potential has a significant effect on the film morphology and/or grain size, such that the structure tended to grow according to the increase of the deposition potential. A CIS layer deposited at -0.6 V nearly approached the stoichiometric ratio of $CuIn_{0.8}Se_{1.8}$. The growth potential plays an important role in controlling the stoichiometry of CIS films.

• Korean Journal of Materials Research
• /
• v.23 no.11
• /
• pp.613-619
• /
• 2013

$Cu_2ZnSn(S_x,Se_{1-x})_4$ (CZTSSe) thin films were prepared by sulfurization of evaporated precursor thin films. Precursor was prepared using evaporation method at room temperature. The sulfurization was carried out in a graphite box with S powder at different temperatures. The temperatures were varied in a four step process from $520^{\circ}C$ to $580^{\circ}C$. The effects of the sulfurization temperature on the micro-structural, morphological, and compositional properties of the CZTSSe thin films were investigated using X-ray diffraction (XRD), Raman spectra, field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). The XRD and Raman results showed that the sulfurized thin films had a single kesterite crystal CZTSSe. From the FE-SEM and TEM results, the $Mo(S_x,Se_{1-x})_2$ (MoSSe) interfacial layers of the sulfurized CZTS thin films were observed and their thickness was seen to increase with increasing sulfurization temperature. The microstructures of the CZTSSe thin films were strongly related to the sulfurization temperatures. The voids in the CZTSSe thin films increased with the increasing sulfurization temperature.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.18 no.1
• /
• pp.37-43
• /
• 1985

The present investigations were carried out for the purpose of making clear the fundamental features of the compositional difference of agarose and agaropectin in agar prepared from Gellidium amansii collected in different places and seasons, and its effect on properties of agar. The samples, Gellidium amansii, was collected every month from the same locality on the coast of the Ilgwang-myon, Yangsan-gun, Kyongnam, from March 1982 to February 1983. In addition, agarose and agaropectin in agar were isolated by dimethyl sulfoxide. The results obtained were summarized as follows : 1. In seasonal variation, the maximum yield of agar noted from spring through summer, and the minimum in February. 2. The experiment showed that the agarose and agaropectin composition in agar was changed, even if the seaweed collected from the same season was used as raw material. Seasonal variation of agarose and agaropectin contents in agar, the highest content occurred in August, $76.2\%$, and the lowest in January, $50.1%$. 3. Jelly strength, gelation ability of agar tended to increase as the agarose content was risen, but sulfate content was decreased.

• Journal of the Korean Society for Heat Treatment
• /
• v.31 no.5
• /
• pp.220-230
• /
• 2018

The objective of this study is to investigate the effect of solution treatment on the microstructure and corrosion behavior of cast AZ91-4%RE magnesium alloy. In the as-cast state, microstructure of the AZ91-4%RE alloy was characterized by intermetallic ${\beta}(Mg_{17}Al_{12})$, $Al_{11}RE_3$ and $Al_2RE$ phase particles distributed in ${\alpha}-(Mg)$ matrix. After solution treatment, the ${\beta}$ particles with low melting point dissolved into the matrix, but Al-RE phases still remained due to their high thermal stabilities. It was found from the immersion and potentiodynamic polarization tests that corrosion rate of the AZ91-4%RE alloy increased after the solution treatment. On the contrary, EIS tests and EDS compositional analyses on the surface corrosion products indicated that the stability of the corrosion product was improved after the solution treatment. Examinations on the corroded microstructures for the ascast and solution-treated samples revealed that dissolution of the ${\beta}$ particles which play a beneficial role in suppressing corrosion propagation, would be responsible for the deterioration of corrosion resistance after the solution treatment. This result implies that the microstructural features such as amount, size and distribution of secondary phases that determine corrosion mechanism, are more influential on the corrosion rate in comparison with the stability of surface corrosion product.