• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.04a
• /
• pp.544-550
• /
• 1997

In this study, the advanced on-sided stress wave velocity measurement method was applied to investigate the effects of composition, age and moisture content in concrete. Two concrete specimens that have different composition were used to figure out the change of the Longitudinal and Surface wave velocity due to different composition. The other concrete specimen was cast and the Longitudinal and Surface wave velocity was monitored during curing process. After 28-day old, the effect of moisture content in the concrete specimen to the stress wave velocity is presented in this paper during the time period 43-74 days after casting. For drying process. an aggregate drying oven was used. A conventional ultrasonic through transmission method was used to compare with the results determined by the one-sided method.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2001.11a
• /
• pp.304-309
• /
• 2001

With the development of electromagnetic communication technology and increased use of electromagnetic wave, the countermeasure of EMI(Electromagnetic Interference) becomes more important socially, and interest for the electromagnetic wave absorber has also increased. In this paper, we have studied characteristics of frequency dependency on complex permittivity and complex permeability according to the changes of composition rate and sintering temperature of NiCuZn ferrite also known as electromagnetic wave absorber and further looked into effect of electromagnetic wave absorption properties. From the measurement where the composition of Fe$_2$O$_3$ and ZnO of NiCuZn ferrite was fixed at 49 and 34 mol% respectively while composition of NiO and CuO has been varied at each test, we found out that initial permeability and permittivity were high and the absorbing ability of electromagnetic wave recorded best with loss tangent(${\mu}$r"/${\mu}$r′) displays more than 1 within the frequency band of 2MHz～9.5MHz when the composition ratio of NiO was ranged around 8.5～9.5 mol% and the sintering temperature was 1,080$^{\circ}C$.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.5
• /
• pp.994-1000
• /
• 2001

With the development of electromagnetic communication technology and increased use of electromagnetic wave, the countermeasure of EMI(Electromagnetic Interference) becomes more important socially, and interest for the electromagnetic wave absorber has also increased. In this paper, we have studied characteristics of frequency dependency on complex permittivity and complex permeability according to the changes of composition rate and sintering temperature of NiCuZn ferrite also known as electromagnetic wave absorber and further looked into effect of electromagnetic wave absorption properties. From the measurement where the composition of $Fe_2O_3$ and ZnO of NiCuZn ferrite was fixed at 49 and 34 mol% respectively while composition of NiO and CuO has been varied at each test, we found out that Initial permeability and permittivity were high and the absorbing ability of electromagnetic wave recorded best with $loss tangent(=\mur"/\mur')$ displays more than 1 within the frequency band of 2MHz~9.5MHz when the composition ratio of NiO was ranged around 8.5~9.5 mol% and the sintering temperature was $1080^{\circ}C$.TEX>.

• Electrical & Electronic Materials
• /
• v.8 no.6
• /
• pp.744-751
• /
• 1995

This paper describes a study on absorption properties of electromagnetic wave by the composition ratio of Ni-Zn ferrite. Ni-Zn ferrite was composed of 48-52mol% Fe$\_$2/O$\_$3/, 18-22mol% NiO and 26-34mol% ZnO. The sintering of the composition was carried out at 1200.deg. C for 2 hours. Through the experiments, it was found that the resonance phenomenon occured at low frequency range for high permeability and vice versa. In the case of the composition of 49mol% Fe$\_$2/O$\_$3/, 20mol% NiO and 31mol% ZnO, the bandwidth ranged from 0.35GHz to 0.95GHz with the absorption thickness of 10mm. Also, in the case of the composition 51mol% Fe$\_$2/O$\_$3/, 22mol% NiO and 27mol% ZnO, the bandwidth ranged from 0.48GHz to 1.2GHz with the absorption thickness of 6mm.

• Journal of electromagnetic engineering and science
• /
• v.12 no.1
• /
• pp.20-25
• /
• 2012

In this paper, the EM wave absorber for ETC system was designed and fabricated. We fabricated several samples in different composition ratios of flaked sendust and CPE(Chlorinated Polyethylene). Absorption abilities were simulated in accordance with different thicknesses of the prepared absorbers and changed complex relative permittivity and permeability according to composition ratio. The optimized mixing ratio of flaked sendust and CPE was found as 60 : 40 wt.% by experiments and simulation. Then the EM wave absorber was fabricated and tested using the simulated data. As a result, the developed EM wave absorber has the thickness of 2.75 mm and absorption ability was 22.5 dB in the case of normal incidence at 5.8 GHz. Therefore, it was confirmed that the newly developed absorber can be used for ETC system.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.820-826
• /
• 2008

Differ number of seismograph to the composition dam by recently frequent earthquake and analyzed responsiveness. Interest for dam inner place by increase of something wrong flood and inside and outside of the country earthquake appearance according to unusual change of weather is risen, on important urea in dam safety floodgate school register by structural safety divide can. Therefore, by PMP (PMF) of dam and increase of domestic earthquake occurrence, need research about earthquake resistant nature ability estimation of water resources facilities. Because responsiveness analysis applies number 0.154 ~ 0.25 g of seismograph, seismic wave that use in analysis is being suitable in dynamic analysis of construction such as Rockfill dam from representative chapter cycle faction and recommend in domestic internal examination design workbook, and use results applied much Hachinohe wave onions in van abroad.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.14 no.1
• /
• pp.34-40
• /
• 2002

In order to estimate the height of long period wave from character of deep water wave, field observation is carried out three wave gauge are arranged by a straight line from the seashore to offshore direction and the result is analyzed. In addition, the existing theory of the mechanism for long period wave producer is verified by field observation, and the relation between deep water wave and long period wave of shallow area is examined. Observed long period wave is coincided with the existing theory for the most part. In order to add the change of time and space of long period wave, the height of long period wave is calculated by the composition of long period wave in each position. As a result, the relation of long period wave and deep water wave is presented more clear. Estimate formula is drew through them.

• Steel and Composite Structures
• /
• v.37 no.2
• /
• pp.137-150
• /
• 2020

In this research work, the analytical rotating vibration for functionally graded shell with ring supports are restricted to some volume fraction laws based on Rayleigh-Ritz technique. The frequencies of functionally grade cylindrical shells have been investigated for the distribution of material composition of material with two kinds of material. Stability of a cylindrical shell depends highly on these aspects of material with ring supports. The frequency behavior is investigated with fraction laws versus circumferential wave number, length-to-radius and height-to-radius ratios. The frequencies are higher for higher values of circumferential wave number. The frequency first increases and gain maximum value with the increase of circumferential wave mode. Moreover, the effect of angular speed is also investigated. It is examined that the backward and forward frequencies increases and decreases on increasing the ratio of height- and length-to-radius ratios.

• Proceedings of the IEEK Conference
• /
• 2007.07a
• /
• pp.107-108
• /
• 2007

In this paper, the EM wave absorbers were designed and fabricated for collision-avoidance radars using Carbon of a dielectric material and Permalloy of a magnetic material with CPE, because radar system has some problems including false image and system-to-system interference. We fabricated some samples in different composition ratio of Carbon and Permalloy, and defined that optimum composition ratios of Carbon and Permalloy with CPE were Carbon:CPE=20:80 wt% and Permalloy:CPE=70:30 wt%. And absorption abilities at different thicknesses of the EM wave absorbers were simulated using the material properties. The EM wave absorbers were manufactured based on the simulated design. Simulated and measured results agree very well.

• Proceedings of the IEEK Conference
• /
• 2003.07a
• /
• pp.306-309
• /
• 2003

Carbon uses included (32 wt %) Silicone Rubber, use different composition and thickness and investigated effect and special quality that get to electromagnetic absorber to sintering style Ba Ferrite that have composition of Fe$_2$O$_3$: $Ba_2$CO$_3$= 82.1 : 17.9 wt% to develop high efficiency X-Band electric wave absorber