• KIEAE Journal
• /
• v.8 no.1
• /
• pp.99-104
• /
• 2008

This study surveys the types of form works used for constructing composite basement walls found in domestic construction sites. Based on expert surveys, the research provides criteria for selecting a form work type and cost-benefit analysis for different types of form works. In selecting a form work type, safety was considered the most important factor. It is induced from the survey that a successful construction requires a form work type that could solidly bear the lateral pressure of concrete rather than other types that cut back the cost and shorten the construction period. In the cost-benefit analysis, the benefit was the highest in 'euro-form+soldier system', and the cost was most competent in 'rib-lath+soldier system'. In considering benefit and cost together, 'euro-form+soldier system' was judged to be the best option. This is likely to be attributed to the following reasons: site workers are familiar with euro-forms because it is the most widely used; and, soldier system is more reliable in bearing lateral pressure compared to steel pipes.

• Journal of the Korea Concrete Institute
• /
• v.20 no.5
• /
• pp.573-581
• /
• 2008

In general, conventional sheeting H-pile is often used as a temporary member installed upon construction of outer retaining wall at basement floor. In CBW (composite basement wall), R/C basement wall is combined with H-Pile and resists lateral soil pressure together. This paper presents an experimental results of push out shear test of CBW with stud coupler as shear connectors to combine H-Pile with R/C wall six specimens with different diameter of FT (form tie) and arrangement of shear connectors were tested to evaluate the shear capacity of the composite wall. Test results showed that shear strength increased with diameter of FT. The shear strength of shear connector in CBW could be suitably predicted by using the previous equations codified in the codes. Best correlation, especially, was found when the calculation result by the formula in AISC 360-05 was compared to test one.

• Journal of the Korea Institute of Building Construction
• /
• v.9 no.6
• /
• pp.161-168
• /
• 2009

In an architectural construction, underground construction is a critical path forming a major part of the total construction period and cost, and particularly in big cities, its size has been increasing every year. A basement wall currently constructed in the field needs a large functional work force, and the construction is under progress by the Euroform and Soldier system, which is disadvantageous in terms of the construction period. Therefore, in this research, non-supporting forms which are applicable to the buildings construction were developed, based on the non-supporting forms partly used in some civil engineering works. In addition, the size of a form was assumed and its economical efficiency was compared to that of the Euroform and Soldier system which is used most in construction fields, and the results were analyzed. The study results showed that the construction cost of composite non-supporting forms was higher than that of the Euroform and Soldier system by about 8%, and the construction cost of non-composite non-supporting forms were lower than that of the Euroform and Soldier system by about 9%. However, in the case of composite non-supporting forms, the amount of concrete and reinforcing rods remarkably decreased in structural construction, so it has the effect of an economical cost reduction compared to the construction cost of existing walls by about 35%

• Journal of the Korean Geotechnical Society
• /
• v.26 no.6
• /
• pp.39-44
• /
• 2010

In case of the design method, which is used in the inside and outside of the country, on corrugated multi plate structures, section modulus would be determined by assuming 2-dementioanl equivalent section of those structures. However, it is impossible to consider 3-dimentional effects when 2-dimentional design method is applied since structures are reinforced with a pattern of the 1200, 1600 mm reinforcements except the 800 mm reinforcement. Thus, in this study, technical specification standard is analyzed for the existing corrugated multi plate design methods, and section strengths, moments, and so on of equivalent and practical sections are compared and estimated using 3-dimentional FEM (finite element method) for semicircles and architectural features widely used. Based on the results of that analysis, analytical basis for 3-dimentional design of the CBS-RIB is suggested.