• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.05a
• /
• pp.247-250
• /
• 1999

In this study, three kinds of Mn-Zn ferrite/Ni-Zn ferrite/$Ni_2Y$ ferroxplana prepared by the coprecipitation method was compounded with silicon rubber, and thereafter made ring-type specimens with various compositional ratio. The material constant of ferrite/rubber composite absorbers was obtaibed by the 2-port method. The material constants of the ferrite/rubber composite absorber with various compositional ratio of three kinds of ferrite were used to design the matching frequency and thickness with the impedance matching map. We were able to predict the matching condition from the design method.

• Composites Research
• /
• v.27 no.6
• /
• pp.225-230
• /
• 2014

In this study, a novel microwave absorber which consists of a structural part, a resistive sheet, and a low dielectric layer is proposed. Unlike the conventional Salisbury screen, a newly proposed absorber is capable of a range of absorbing performance, from narrowband to broadband. In the case of the narrowband absorber, the fabricated absorber with optimized design parameters has a strong resonance at 9.25 GHz and reflection loss of -44 dB with satisfying the -10 dB absorption in whole X-band (8.2 GHz~12.4 GHz). For the broadband absorber design, the reflectivity was minimized in the considered frequency ranges. The designed absorber showed two weak resonances near 6.5 GHz and 16.5 GHz and satisfied the -10 dB absorption from C-band to Ku-band (4 GHz~18 GHz). The measured reflection loss of fabricated absorber was well matched with simulation results, though the measurement was only performed on X-band. For the Salisbury screen to be capable of broadband absorption, it should be stacked multiply in a structure known as the Jaumann absorber. However, for the microwave absorber presented here, broadband as well as narrowband capabilities can be implemented without a change of the structure.

• Journal of the Korean Ceramic Society
• /
• v.31 no.4
• /
• pp.415-419
• /
• 1994

The material constants(the complex permeability and permittivity) of ferrite composite determine its microwave absorbing characteristics. Therefore, in order to improve the microwave absorbing characteristics, it is necessary to control the material constants of the ferrite composite. In this study, the method of improving microwave absorbing characteristics by control of permittivity of ferrite composite which has not satisfying matching condition in C-X band (4 GHz~12.4 GHz) was investigated. It was possible to control the permittivity by adjusting graphite loading ratio in the ferrite composite microwave absorber. It was also concluded that the control of permittivity of ferrite composite is effective method to improve the microwave absorbing characteristics.

• Proceedings of the KIEE Conference
• /
• 1994.07b
• /
• pp.1478-1480
• /
• 1994

In this paper, the microwave absorption properties of two layered absorber were evaluated. The two layer absorber were composed of Ni-Zn ferrite/rubber absorber and Ferroxplana/rubber absorber. The most absorption properties condition were obtained when the transforming layer and absorbing layer were Ferroxplana/robber absorber and Ni -Zn ferrite/rubber absorber. respectivity. The optimal thickness of the transforming and the absorbing layer were 4(mm) and 1(mm), respective1y.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.155-161
• /
• 2000

In this paper, we studied the relation between heat-treatment temperature of ferrite and electromagnetic wave absorbing properties of ferrite-rubber composite. The heat-treatment temperatures of ferrite are 1200 and $1300^{\circ}C$, 2 hr. As s result. it has been shown that the optimum heat-treatment temperature of ferrite for electromagnetic wave absorber are related to the chemical composition. And, we can control electromagnetic wave absorbing properties of ferrite-rubber composite by the control of heat-treatment temperature of ferrite.

• Journal of the Korean Institute of Navigation
• /
• v.23 no.1
• /
• pp.15-22
• /
• 1999

In this paper, ferrite-rubber composite has been studied in order to apply to RF-A-PF in a super wideband electromagnetic absorber in RF-A-PF type, which can be used for a general purpose anechoic chamber. $Ni_x - Mn_0.1 - Zn_{(1-x-0.1)}ㆍFe_2O_4$ ferrite powder has been fabricated, then, using this, 〔$Ni_x - Mn_0.1 - Zn_{(1-x-0.1)}ㆍFe_2O_4$〕-Rubber composite for RF-layer in the RF-A-PF type absorber has been fabricated and it's characteristics have been analyzed. As a result, it has been clearly shown that the 〔$Ni_x - Mn_0.1 - Zn_{(1-x-0.1)}ㆍFe_2O_4$〕-Rubber composite has excellent electromagnetic wave absorbing properties.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.3 no.1
• /
• pp.35-42
• /
• 1999

This paper describes the characteristics of the complex isotropic ferrite-rubber composite for a super wideband electromagnetic absorber in RP-A-PF type, which can be used for an anechoic chamber, wall material to prevent TV ghost, etc. The $Ni_x-A_{0.1}-ZN_{(1-x0.1)}$. $Fe{_2}O_4$ ferrite powder has been fabricated. Using this, then, [$Ni_x-A_{0.1}-ZN_{(1-x0.1)}$. $Fe{_2}O_4$]-Rubber composite for RF-layer in the RF-A-PF type absorber has been fabricated and it's characteristics has been analyzed. As a result, it has been shown that the [$Ni_x-A_{0.1}-ZN_{(1-x0.1)}$. $Fe{_2}O_4$].Rubber composite has excellent electromagnetic wave absorbing properties.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 1996.09a
• /
• pp.111-116
• /
• 1996

To realize the RF layer of Rubber Ferrite-Air-Solid Ferrite(RF-A-F) that proposed by Y.Naito it is tried to grasp the formulation of composition by varying the ratio of mole and element of Complex Isotropic Ferrite Nix-A0.1-Zn(1-x-0.1)*Fe2O4 As a result it was found that the characteristics of the electromagnetic wave absorber constructed by the selected formulation of compositionin in RF-A-F type were improved.

• Journal of the Korean Ceramic Society
• /
• v.31 no.1
• /
• pp.11-16
• /
• 1994

The impedance matching solution map is not a sufficient method for designing the broad-band absorber because of its difficulty to get numerical data about practical band-width. Therefore, we develope a new method to design the broad-band absorber. The complex permeability limits, which is necessary for designing the broad-band absorber in C-X band (4 GHz~12.4 GHz) were investigated and application was also examined. The complex permeability limits represent the frequency dependence of the complex permeability at a practical frequency band. These complex permeability limits can be used effectively to design broad-band single-layered absorber because they offer numerical data about the band-width in the case of various dielectric loss tangent, practical frequency bands and permitted reflection losses of an absorber.

• Composites Research
• /
• v.29 no.3
• /
• pp.98-103
• /
• 2016

This paper deals with the fabrication and verification of the microwave absorbing structure using semiconductive fiber reinforced composite. Two kinds of fiber were used to fabricate composites. Electromagnetic properties of the composites were measured by freespace measurement system over X-band. Two single slab absorbers and a double slab absorber were designed by thickness optimization method. Single slab absorbers did not show good microwave absorption performance because the permittivity is away from non-reflection curve. Double slab absorber complemented the limitations on single slab absorber and it showed good microwave absorption performance. Double slab absorber showed -43.9 dB loss near 10 GHz.