• 한국도로학회논문집
• /
• 제12권3호
• /
• pp.121-129
• /
• 2010

본 연구는 합리적인 단지 내 도로포장의 표준단면을 제시하기 위해 국내외 단지 내 도로포장 설계기준, 주요 파손형태를 조사하고 다양한 포장설계 단면을 대상으로 구조해석을 수행하였다. 이때, 현장에서 사용된 보조기층재와 노상토의 시편을 채취하여 CBR 및 MR 시험을 실시하였으며, 측정한 물성치를 구조해석에 적용하였다. 다양한 현장조건을 고려한 구조해석 결과를 분석하여, 표준단면의 포장층 두께를 보조기층 20cm, 아스팔트기층 5cm, 그리고 표층 5cm로 제안하였다. 또한, 민원이 예상되는 도시지역에서는 일반적으로 아스팔트 기층을 포설한 후 공사차량을 개방하여 작업종료 후에 표층을 포설하게 되는데 이러한 여건을 고려하여 단지 내 아스팔트 콘크리트 포장 표준단면의 포장층의 두께를 보조기층 20cm, 아스팔트 기층 7cm, 그리고, 표층 5cm로 제시하였다.

• 대한기계학회논문집B
• /
• 제33권11호
• /
• pp.840-848
• /
• 2009

In the boiling heat transfer mechanism, CHF(critical heat flux) is the significantly important parameter of the system. So, many researchers have been struggling to enhance the CHF of the system in enormous methods. Recently, there were lots of researches about enormous CHF enhancement with the nanofluids. In that, the pool boiling CHF in nanofluids has the significantly increased value compared to that in pure water because of the deposition of the nanoparticle on the heater surface in the nanofluids. The aim of this study is the comparison of the effect of the nanoparticle deposited surface and the modified surface which has the similar morphology and made by MEMS fabrication. The nanoparticle deposited surface has the complex structures in nano-micro scale. Therefore, we fabricated the surfaces which has the similar wettability and coated with the micro size post and nano structure. The experiment is performed in 3 cases : the bare surface with 0.002% water-ZnO nanofluids, the nanoparticle deposited surface with pure water and the new fabricated surface with pure water. The contact angle, a representative parameter of the wettability, of the all 3 cases has the similar value about 0 and the SEM(scanning electron microscope) images of the surfaces show the complex nano-micro structure. From the pool boiling experiment of the each case, the nanoparticle deposited surface with pure water and the fabricated surface with pure water has the almost same CHF value. In other words, the CHF enhancement of the nanoparticle deposited surface is the surface effect. It also shows that the new fabricated surface follows the nanoparticle deposited surface well.

• Ocean and Polar Research
• /
• 제30권3호
• /
• pp.313-324
• /
• 2008

In order to understand the variation of ENSO-related oceanic environments in the tropical and North Pacific Ocean, spatio-temporal variations of sea surface temperature anomaly (SSTA) and sea surface height anomaly (SSHA) are analyzed from distributions of complex empirical orthogonal functions (CEOF). Correlations among warm pool variation, southern oscillation index, and ocean surface currents were also examined with respect to interannual variability of the warm pool in western tropical Pacific. Spatio-temporal distributions of the first CEOF modes for SSTA and SSHA indicate that their variabilities are associated with ENSO events, which have a variance over 30% in the North Pacific. The primary reasons for their variabilities are different; SST is predominantly influenced by the change of barrier layer thickness, while SSH fluctuates with the same phase as propagation of an ENSO episode in the zonal direction. Horizontal boundary of warm pool area, which normally centered around $149^{\circ}E$ in the tropics, seemed to be expanded to the middle and eastern tropical regions by strong zonal currents through the mature phase of an ENSO episode.

• Journal of Welding and Joining
• /
• 제25권3호
• /
• pp.78-84
• /
• 2007

Laser Material Processing has been replaced the conventional machining systems - cutting, drilling, welding and surface modification and so on. Especially, LTH(Laser Transformation Hardening) process is one branch of the laser surface modification process. Conventionally, some techniques like a gas carburizing and nitriding as well as induction and torch heating have been used to harden the carbon steels. But these methods not only request post-machining resulted from a deformation but also have complex processing procedures. Besides, LTH process has some merits as : 1. It is easy to control the case depth because of output(laser power) adjustability. 2. It is able to harden the localized and complicated a.ea and minimize a deformation due to a unique property of a localized heat source. 3. An additional cooling medium is not required due to self quenching. 4. A prominent hardening results can be obtained. This study is related to the surface hardening of the rod-shaped carbon steel applied to the lathe based complex processing mechanism, a basic behavior of surface hardening, hardness distribution and structural characteristics in the hardened zone.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회B
• /
• pp.2737-2742
• /
• 2007

Strong wind flow around a building complex was numerically studied by LES. The original motivation of this work stemmed from the efforts to develop a risk assessment technique for windstorm hazards. Lagrangian-averaged scale-invariant dynamic subgrid-scale model was used for turbulence modeling, and a log-law-based wall model was employed on all the solid surfaces including the ground and the surface of buildings to replace the no-slip condition. The shape of buildings was implemented on the Cartesian grid system by an immersed boundary method. Key flow quantities for the risk assessment such as mean and RMS values of pressure on the surface of the selected buildings are presented. In addition, characteristics of the velocity field at some selected locations vital to safety of human beings is also reported.

• Food Science and Biotechnology
• /
• 제18권1호
• /
• pp.185-189
• /
• 2009

Microencapsulation of flavor was carried out by molecular inclusion process using $\beta$-cyclodextrin (${\beta}CD$). ${\beta}CD$-flavor complex was prepared at various flavor-to-${\beta}CD$ ratios (1:6-1:12) to determine the effect of ${\beta}CD$ concentration on the inclusion efficiency. Maximum total oil retention and minimal surface oil content were obtained at flavors to ${\beta}CD$ ratio of 1:10. The physical properties and controlled release pattern of flavors from ${\beta}CD$-flavor complex were measured and compared with spray-dried microcapsules prepared using carbohydrate wall system. ${\beta}CD$-flavor complex showed higher total oil retention and surface oil contents, smaller mean particle size, lower moisture uptake, and higher oxidation stability than spray-dried microcapsule. Oxidative stability of flavor was correlated with hygroscopicity of wall materials. The controlled release mechanism was highly affected by temperature and characteristics of wall materials.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 추계 학술발표회 제16권2호
• /
• pp.221-224
• /
• 2004

Several factors of concrete durability decline factor are acted as complex deterioration and is happened not that happen by simplicity deterioration. Specially, in case of sea construction, as complex salt damage, carbonation and freezing & thawing, concrete surface and pore structure is deteriorated. Therefore, analyzing concrete carbonation and pore structure after freezing and thawing test by fresh water and sea water in this research, we wish to study about acceleration of decline of durability and complex deterioration by concrete surface deterioration in sea environment.

• 대한치과교정학회지
• /
• 제16권2호
• /
• pp.43-51
• /
• 1986

The highly accurate laser holographic interferemotry method was used to determine in what way low-magnitude forces during maxillary expansion are transmitted to the entire maxillary complex and its surrounding structures. The experiments were carried out on a dryed human skull which had a perfectly preserved, normally aligned maxillary dental arch and intact alveolar process. The skull was fixed within a constructed metal frame which ensured maximal stability of the object. The optical equipment and the object were mounted on antivibration table. Interferograms were taken on the lateral and frontal sides of the maxillary complex, using the 10mW He-Ne laser and the double-exposure method. Analysis of the fringe pattern on the recorded object surface was performed by graphically determining the deformation curves related to the bony surface in selected horizontal and vertical planes. On the basis of this study, the following conclusions can be drawn: 1. The density of the interference fringes was gradually increased with the degree of expansion force. 2. Mechanical reactions on the maxillary complex, circummaxillary sutures, and surrounding bones were clearly visible, even with the lowest loading degree. 3. The amount of bone displacement was greater in application of the force after $90^{\circ}$ turn than in initial application of the same force. 4. The direction of interference fringes on the bony surface was similar at all loading degrees.

• Biotechnology and Bioprocess Engineering:BBE
• /
• 제9권3호
• /
• pp.179-183
• /
• 2004

A biocompatible polyelectrolyte complex multilayer (PECML) film consisting of poly-L-lysine (PLL) as a polycation and hyaluronic acid (HA) as a polyanion was developed to test its use for surface modification to prevent cell attachment and protein drug delivery. The formation of PECML through the electrostatic interaction of HA and PLL was confirmed by contact angle measurement, ESCA analysis, and HA content analysis. HA content increased rapidly up to 8 cycles for HA/PLL deposition and then slightly increased with an increasing number of deposition cycle. In vitro release of PLL in the PECML continued up to 4 days and ca. 25% of HA remained on the chitosan-coated cover glass after in vitro release test for 7 days. From the results, PECML of HA and PLL appeared to be stable for about 4 days. The surface modification of the chitosan-coated cover glass with PECML resulted in drastically reduced peripheral blood mononuclear cell (PBMC) attachment. Concerned with its use for protein drug delivery, we confirmed that bovine serum albumin (BSA) as a model protein could be incorporated into the PECML and its release might be triggered by the degradation of HA with hyaluronidase.

• IMMUNE NETWORK
• /
• 제2권1호
• /
• pp.35-40
• /
• 2002

Background: CTLA-4 (Cytotoxic T Lymphocyte associated Antigen 4, CD152) has been known as a homologue of CD28, an accessory molecule providing a key costimulatory signal for successful antigen-driven activations of T lymphocyte. Most of biochemical and cell biological characteristics of the CD152 protein remain unknown while those of CD28 have been characterized in detail. Methods: In this study CD152 expression in both $CD4^+$ and $CD8^+$ PBLs was studied by using flow cytometry. And intracellular CD152 multiprotein complex was purified and used for generating antibodies recognizing proteins composing of intracellular CTLA-4 multi protein complex. Results: Level of surface expression of this molecule was peaked at 2 days of PHA stimulation in flow cytometric analysis. 40~45% of PHA blast cells were $CD152^+$ in both of two subsets at this stage and the level of expression were equivalent in both two subsets. Contrary to this surface expression, intracellular expression was peaked at day 3 and it was preferentially induced in $CD8^+$ cells and about 60% of $CD8^+$ cells were $CD152^+$ at this stage. High molecular weight (>350 kD) intacellular CD152 protein complex purified by using preparative electrophoresis were immunized into rabbits and then 3 different anti-P34PC4, anti-P34PC7 and anti-P34PC8 antibodies were obtained. Using these 3 antibodies two unknown antigens associated with intracellular CD152 multiprotein complex were found and their molecular weights were 54 kD and 75 kD, respectively. Among these, the former was present as 110 kD homodimer in non-reducing condition. Conclusion: It seemed that 34 kD intracellular CD152 molecule forms high molecular weight multiprotein complex at least with 2 proteins of 75 kD monomer and 110 kD homodimer.