• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.1749-1753
• /
• 2003

We proposed several systems for 1Giga bit Modem. The first, Binary ASK(Amplitude Shift Keying) system has a high speed shutter transmitter and no IF(Intermediate Frequency) receiver only by symbol synchronization. The advantage of proposed system is that circuitry is very simple without IF process. The disadvantage of proposed system are that line spectrum occurs interference to other channels, and enhancement to 4-level system is impossible due to its large SNR degradation. The second, Binary phase modulation system has a high speed shutter transmitter and IF-VCO(IF-Voltage Controlled Oscillator) control by base-band phase rotation. Polarity of shutter window is changed by the binary data. The window should be narrow same as above ASK. The advantage of proposed system is which error rate performance is superior. The disadvantage of proposed system are that Circuitry is more complex, narrow pull-in range of receiver caused by VCO and spectrum divergence by the non-linear amplifier. The third, 4-QAM(Quadrature Amplitude Modulation)system has a nyquist pulse transmitter and IF-VCO control by symbol clock. The advantage of proposed system are that signal frequency band is a half of 1GHz, reliable pull-in of VCO and possibility of double speed transmission(2Gbps) by keeping 1GHz frequency-band. The disadvantage of proposed system are that circuit complexity of pulse shaping and spectrum divergence by the non-linear amplifier.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.2
• /
• pp.31-37
• /
• 2009

This paper presents an efficient frame synchronization strategy with the identification of modulation type for Digital Video Broadcasting-Satellite second generation (DVB-S2). To detect the Start Of Frame (SOF) and identify a modulation mode at low SNR, we propose a new correlator structure and a low complexity Automatic Gain Controller (AGC). The proposed frame synchronization architecture can reduce about 93% multipliers and 89% adders compared with the direct implementation of the Differential - Generalized Post Detection Integration (D-GPDI) algorithm which is very complex and the proposed a low complexity AGC consists of only 5 multipliers and 3 adders. The proposed architecture has been thoroughly verified on the Xilinx Virtex II FPGA board.

• Journal of the Korean Society of Radiology
• /
• v.4 no.3
• /
• pp.31-37
• /
• 2010

In this paper, a photovoltaic system is designed with PWM(Pulse Width Modulation) voltage source inverter. Proposed synchronous signal and control signal was processed by 56F8323 microprocessor for stable modulation. The PWM voltage source inverter using inverter consists of complex type of electric power converter to compensate for the defect, that is solar cell cannot be developed continuously by connecting with the source of electric power for ordinary use. It can cause the effect of saving electric power, from 10 to 20[%]. The PWM voltage source inverter operates in situation that its output voltage is in same phase with the utility voltage. In addition, I connected extra power to the system through operation the system voltage and inverter power in a synchronized way by extracting the system voltage so that the phase of the system and PWM voltage inverter can be synchronized. In the system of this research showed good results after being controlled in order to provide stable power to the load and the system through maintaining and low output power of harmonics.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.6
• /
• pp.68-73
• /
• 2009

One of the traditional optical methods to monitor a tool is a CCD sensor-based vision system which captures an aspect of the tool in real time. In the case using the CCD sensor, specific lens-modules are necessary to monitor the tool with higher resolution than its pixel size, and a microprocessor is required to attain desired data from captured images. Thus theses additional devices make the entire measurement system complex. Another method is to use a pair of an optical source and a detector per measuring axis. Since the method is based on the intensity modulation, the structure of the measurement system is simper than the CCD sensor-based vision system. However, in the case measuring the three dimensional position of the tool, it is difficult to apply to micro machine-tools because there may not be space to integrate three pairs of an optical source and a detector. In this paper, in order to develop a tool-origin measurement system which is employed in micro machine-tools, the improved method to measure a tool origin in x, y and z axes is introduced. The method is based on the intensity modulation and employs one pair of an optical source radiating divergent beams and a quadrant photodiode to detect a three dimensional position of the tool. This paper presents the measurement models of the proposed tool-origin sensor. The models were verified experimentally The verification results show that the proposed method is possible and the induced models are available for design.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.10 no.11
• /
• pp.5381-5399
• /
• 2016

Currently, the quantize-and-forward (QF) scheme with high order modulation and quantization has rather high complexity and it is thus impractical, especially in multiple relay cooperative communications. To overcome these deficiencies, an improved low complex QF scheme is proposed by the combination of the low order binary phase shift keying (BPSK) modulation and the 1-bit and 2-bit quantization, respectively. In this scheme, the relay selection is optimized by the best relay position for best bit-error-rate (BER) performance, where the relays are located closely to the destination node. In addition, an optimal power allocation is also suggested on a total power constraint. Finally, the BER and the achievable rate of the low order 1-bit, 2-bit and 3-bit QF schemes are simulated and analyzed. Simulation results indicate that the 3-bit QF scheme has about 1.8~5 dB, 4.5~7.5 dB and 1~2.5 dB performance gains than those of the decode-and-forward (DF), the 1-bit and 2-bit QF schemes, at BER of $10^{-2}$, respectively. For the 2-bit QF, the scheme of the normalized Source-Relay (S-R) distance with 0.9 has about 5dB, 7.5dB, 9dB and 15dB gains than those of the distance with 0.7, 0.5, 0.3 and 0.1, respectively, at BER of $10^{-3}$. In addition, the proposed optimal power allocation saves about 2.5dB much more relay power on an average than that of the fixed power allocation. Therefore, the proposed QF scheme can obtain excellent features, such as good BER performance, low complexity and high power efficiency, which make it much pragmatic in the future cooperative communications.

• Journal of Digital Convergence
• /
• v.20 no.1
• /
• pp.185-190
• /
• 2022

Bluetooth is a common wireless technology that is widely used as a connection medium between various consumer electronic devices. The Bluetooth receiver usually adopts a Viterbi algorithm to improve signal-to-noise ratio performance, but requires complex hardware and calculations for continuous search and estimation for the irrational modulation indexes at the transmission. This paper proposes a non-coherent maximum estimation based 8-State Viterbi FSM to solve these complexity problems. The proposed optimal Viterbi FSM can detect Gaussian frequency-shfit keying symbol without any prior information and estimation for the modulation indexes. The HV1/HV2 packets are used for the estimation of the proposed algorithm and the simulation results have shown performance improvements with about 2dB for 10^-3 BER compared to other ideal approaches such as decision direct method.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.3 s.345
• /
• pp.59-67
• /
• 2006

OFDM (Orthogonal frequency Division Multiplexing) systems convert serial data stream to N parallel data streams and modulate them to N orthogonal subcarriers. Thus spectrum utilization efficiency of the OFDM systems are high and high-speed data transmission is possible. However, with the OFDM systems using the same modulation method at all subcarriers, the error probability is dominated by the subcarriers which experience deep fades. Therefore, in order to enhance the performance of the system adaptive modulation is required, with which the modulation methods of the subcarriers are determined according to the estimated SNRs. The IEEE 802.11a system selects various transmission speed between 6 and 54 Mbps according to the modulation mode. There are three typical methods for SNR estimation: Direct estimation method uses the frequency domain symbols to estimate SNR directly by minimizing MSE (Mean Square Error), EVM method utilizes the distance between the demodulated constellation points and received complex values, and the method utilizing the Viterbi algorithm uses the cumulative minimum distance in decoding process to estimate the SNR indirectly. Through comparison analyses of three methods we propose a new SNR estimation method, which employs both the EVM method and the Viterbi algorithm. Finally, we perform extensive computer simulations to confirm the performance improvement of the proposed adaptive OFDM systems on the basis of IEEE 802.11a.

• Development and Reproduction
• /
• v.11 no.1
• /
• pp.1-11
• /
• 2007

Specific endometrial preparation should occur during periimplantation period. That is a progress of serial differentiation and is absolute in implantation of embryo and successful pregnancy. Remodeling of tissues shown during embryogenesis is regulated by various factors including extracellular matrix (ECM). Marked changes during pregnancy are including embryo migration, decidual response, and differentiation of placenta in placental animals including human. These changes to successful implantation in embryo and uterus have to prepare the competence for attachment of embryo and uterus, and invasion defense of uterus. During these changes, ECM dramatically changes for maintaining the uterine and embryonic functions. The major component of most connective tissue is collagens. It is very complex and hard to explore the mechanisms for ECM modulation. Recently using high throughput methodology, PCR-select cDNA subtraction method, microarray, many candidate genes have been identified. Steroid hormones have fundamental role in implantation and maintenance of pregnancy. Dermatopontin, a regulator of collagen accumulation, is regulated spatio-temporally in the uterus by primarily progesterone through progesterone receptors at the time of implantation. Modulation of extracellular matrix is critically regulated by cascade of gene net-works which are regulated by cascade of sex steroid hormones. Pathological regulation of uterine extracellular matrix reported in diabetic patients. To know the extracellular modulation is essential to understanding implantation, feto-placental development and overcome the paths involved in female reproduction. Though ECM composed with very various components and it is complex, the present review focused on the fate of collagens during periimplantation period.

• International Journal of Control, Automation, and Systems
• /
• v.4 no.5
• /
• pp.601-614
• /
• 2006

In this paper, a study on task assignment strategies for a complex real-time network system is presented. Firstly, two task assignment strategies are proposed to improve previous strategies. The proposed strategies assign tasks with meeting end-to-end real-time constraints, and also with optimizing system utilization through period modulation of the tasks. Consequently, the strategies aim at the optimizationto optimize of system performance with while still meeting real-time constraints. The proposed task assignment strategies are devised using the genetic algorithmswith heuristic real-time constraints in the generation of new populations. The strategies are differentiated by the optimization method of the two objectives-meeting end-to-end real-time constraints and optimizing system utilization: the first one has sequential genetic algorithm routines for the objectives, and the second one has one multiple objective genetic algorithm routine to find a Pareto solution. Secondly, the performances of the proposed strategies and a well-known existing task assignment strategy using the BnB(Branch and Bound) optimization are compared with one other through some simulation tests. Through the comparison of the simulation results, the most adequate task assignment strategies are proposed for some as system requirements-: the optimization of system utilization, the maximization of running tasktasks, and the minimization of the number of network node nodesnumber for a network system.

• IMMUNE NETWORK
• /
• v.21 no.2
• /
• pp.15.1-15.10
• /
• 2021

Abnormal inflammatory responses are closely associated with intestinal microbial dysbiosis. Oral administration of Qmatrix-diabetes-mellitus complex (QDMC), an Aloe gel-based formula, has been reported to improve inflammation in type 2 diabetic mice; however, the role of the gut microbiota in ameliorating efficacy of QDMC remains unclear. We investigated the effect of QDMC on the gut microbiota in a type 2 diabetic aged mouse model that was administered a high-fat diet. Proinflammatory (TNF-α and IL-6) and anti-inflammatory (IL-4 and IL-10) cytokine levels in the fat were normalized via oral administration of QDMC, and relative abundances of Bacteroides, Butyricimonas, Ruminococcus, and Mucispirillum were simultaneously significantly increased. The abundance of these bacteria was correlated to the expression levels of cytokines. Our findings suggest that the immunomodulatory activity of QDMC is partly mediated by the altered gut microbiota composition.