• 한국정보디스플레이학회:학술대회논문집
• /
• 2005.07a
• /
• pp.659-662
• /
• 2005

This paper presents a new technology, Advanced Dynamic Capacitance Compensation (A-DCC), for improved dynamic performance of LCD monitors. Conventional LCD monitors suffer from certain specific artifacts, such as wire-frame flicker and line dimming, which are not an issue for the simpler motion images found in television content. A-DCC addresses these more challenging monitor cases through an advanced architecture which analyzes multi-frame data and applies more comprehensive lookup table corrections according to the specific frame sequence.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.2
• /
• pp.233-243
• /
• 1994

Generally, fuzzy PI controller that regulates the gains using fuzzy algorithm shows high performance in speed response. However, it has some problems to the load inertia variation, because the change of speed error(CE) is in a fixed range. As load inertia increases, CE is decreased and the usuage of fuzzy table is limited. Therefore, the output of the fuzzy controller has a limited range. This paper proposes an improved fuzzy PI controller. To reduce the speed overshoot, we adapt a control method that selects a proper CE range with respect to the load inertia variation. The proposed controller is applied to the vector controlled system with 2.2kW induction motor. Some simulation and experimental results are exhibited. With these results, we can easily find that proposed PI controller is more robust than the conventional fuzzy PI controller against the load inertia variation.

• Proceedings of the KIPE Conference
• /
• 2010.11a
• /
• pp.310-311
• /
• 2010

하이브리드 자동차(HEV)용 매입형 영구자석 동기 전동기(IPMSM)의 Lookup-Table을 이용한 토크제어는 전류 및 온도 등과 같은 외부 환경에 의한 파라미터 변동으로 인해 전체적인 구동 성능이 떨어지게 된다. 따라서 본 논문에서는 전류 및 자속 값을 이용하여 지령 토크에 대한 전류 지령치를 보상함으로써 출력 토크를 보상하였다. 구동 성능은 시뮬레이션을 통하여 확인하였다

• Journal of the Korea Concrete Institute
• /
• v.14 no.3
• /
• pp.291-298
• /
• 2002

Recently, construction of reinforced concrete tall buildings is widely increased according to the improvement of material quality and design technology. Therefore, differential shortenings of columns due to elastic, creep, and shrinkage have been an important issue. But it has been neglected to predict the Inelastic behavior of RC structures even though those deformations make a serious problem on the partition wall, external cladding, duct, etc. In this paper, analysis system for prediction and compensation of the differential column shortenings considering time-dependent deformations and construction sequence is developed using the objected-oriented technique. Developed analysis system considers the construction sequence, especially time-dependent deformation in early days, and is composed of input module, database module, database store module, analysis module, and analysis result generation module. Graphic user interface(GUI) is supported for user's convenience. After performing the analysis, the output results like deflections and member forces according to the time can be observed in the generation module using the graphic diagram, table, and chart supported by the integrated environment.

• IEIE Transactions on Smart Processing and Computing
• /
• v.2 no.5
• /
• pp.310-316
• /
• 2013

This paper reports a sinusoidal $180^{\circ}$ drive for a permanent magnet (PM) brushless motor employing automatic angle compensator to suppress the driving loss during the wide-range load operation. The proposed drive of the sinusoidal $180^{\circ}$ PM Brushless motor reduced the amplitude of the 3-phase current by compensating for the lead-angle of the fundamental waves of the 3-phase PWM signal. The conventional lead-angle method was implemented using the fixed angle or memorized table, whereas the proposed method was automatically compensated by calculating the angle of the current and voltage signal. The algorithm of the proposed method was verified in a 30 W PM brushless motor system using a PSIM simulator. The efficiency of the conventional method was decreased 90 % to 60 %, whereas that of proposed method maintained approximately 85 % when the load shift was 0 to $0.02N{\cdot}m$. Using an FPGA prototype, the proposed method was evaluated experimentally in a 30 W PM brushless motor system. The proposed method maintained the minimum phase RMS current and 79 % of the motor efficiency under 0 to $0.09N{\cdot}m$ load conditions. The proposed PM brushless motor driving method is suitable for a variety of applications with a wide range of load conditions.

• Journal of the Korean Society of Physical Medicine
• /
• v.8 no.2
• /
• pp.183-192
• /
• 2013

PURPOSE: The purpose of this study was to research the effect of self-Stretching Exercise on musculoskeletal Symptom and job Stress for care helpers who work at geriatric hospital and come up to NIOSH standard. METHODS: The effect of self-Stretching Exercise was measured using 'musculoskeletal symptom survey table' and 'Job stress measurement scale for korean' from the Korea Occupational Safety and Health Agency(KOSHA) for 40 care helpers. The paired t-test and independent t-test was used for statistical analysis. RESULTS: The pracitce of Self-Stretching Exercise was showed significant effect reducing the stress for care helper's total job Stress and inappropriate compensation, job instability, job requirement, relationship conflict, physical environment(p<.05), and significant difference for their total score, relationship conflict, structure and organization, physical environment, inappropriate compensation improvement on variations on job stress in groups(p<.05). However, self-Stretching Exercis was showed no significant effect on physcial burden. CONCLUSION: The self-Stretching Exercise was the most effect way to reduce Musculoskeletal Symptom and job Stress for a care helpers through the guidance of physical therapist.

• Earthquakes and Structures
• /
• v.12 no.4
• /
• pp.425-436
• /
• 2017

Vibration control using a tuned mass damper (TMD) is an effective technique that has been verified using analytical methods and experiments. It has been applied in mechanical, automotive, and structural applications. However, the damping of a TMD cannot be adjusted in real time. An excessive mass damper stroke may be introduced when the mass damper is subjected to a seismic excitation whose frequency content is within its operation range. The semi-active tuned mass damper (SATMD) has been proposed to solve this problem. The parameters of an SATMD can be adjusted in real time based on the measured structural responses and an appropriate control law. In this study, a stiffness-controllable TMD, called a leverage-type stiffness-controllable mass damper (LSCMD), is proposed and fabricated to verify its feasibility. The LSCMD contains a simple leverage mechanism and its stiffness can be altered by adjusting the pivot position. To determine the pivot position of the LSCMD in real time, a discrete-time direct output-feedback active control law that considers delay time is implemented. Moreover, an identification test for the transfer function of the pivot driving and control systems is proposed. The identification results demonstrate the target displacement can be achieved by the pivot displacement in 0-2 Hz range and the control delay time is about 0.1 s. A shaking-table test has been conducted to verify the theory and feasibility of the LSCMD. The comparisons of experimental and theoretical results of the LSCMD system show good consistency. It is shown that dynamic behavior of the LSCMD can be simulated correctly by the theoretical model and that the stiffness can be properly adjusted by the pivot position. Comparisons of experimental results of the LSCMD and passive TMD show the LSCMD with less demand on the mass damper stroke than that for the passive TMD.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.4 no.3
• /
• pp.358-379
• /
• 2010

Multiple object association is an important capability in visual surveillance system with multiple cameras. In this paper, we introduce locally initiating line-based object association with the parallel projection camera model, which can be applicable to the situation without the common (ground) plane. The parallel projection camera model supports the camera movement (i.e. panning, tilting and zooming) by using the simple table based compensation for non-ideal camera parameters. We propose the threshold distance based homographic line generation algorithm. This takes account of uncertain parameters such as transformation error, height uncertainty of objects and synchronization issue between cameras. Thus, the proposed algorithm associates multiple objects on demand in the surveillance system where the camera movement dynamically changes. We verify the proposed method with actual image frames. Finally, we discuss the strategy to improve the association performance by using the temporal and spatial redundancy.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.5
• /
• pp.457-462
• /
• 2014

Given their low cost, single rolling piston compressors (SRPC) are utilized in low-power room air-conditioning systems. The SRPC cycle is composed of one compression and discharge process per mechanical rotation. The load torque is high during the compression process of the refrigerants and low during the discharge process of the refrigerants. This load torque variation induces a speed ripple and severe vibration, which cause fatigue failures in the pipes and compressor parts, particularly under low-speed conditions. To reduce the vibration, the compressor usually operates at a high-speed range, where the rotor and piston inertia reduce the vibration. At a low speed, a predefined feed-forward load torque compensator is used to minimize the speed ripple and vibration. However, given that the load torque varies with temperature, pressure, and speed, a predefined load torque table based on one operating condition is not appropriate. This study proposes an online load torque compensator for SRPC. The proposed method utilizes the speed ripple as a load torque ripple factor. The speed ripple is transformed into a frequency domain and compensates each frequency harmonic term in an independent feed-forward manner. Experimental results are presented to verify the proposed method.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 2010.07a
• /
• pp.220-223
• /
• 2010

최근 연이은 3D 영화의 성공에 힘입어 영화 산업계를 중심으로 3D 콘텐츠 생성이 늘고 있으며, 이를 가정 내에서도 즐길 수 있도록 다양한 3DTV가 출시되고 있다. 그러나 3DTV의 특성 상 3D 재생 시 밝기 저하에 따른 색 재현 문제로 인하여 입체감과 공간감을 느끼는 대신 2D에서의 화려한 색감을 만끽할 수 없게 되었다. 이에 본 논문은 3D 시청 시에도 2D에서와 같은 색감을 최대한 제공하기 위한 방법에 대해 연구하였다. 이를 위하여 3DTV를 활용하여 입력 RGB 영상에 대하여 2D와 3D 재생 시 재현되는 RGB intensity를 측정한 후 입출력에 따른 관계 모델링을 실시하였고, 모델링에 근거하여 3D 재생 시 2D 대비 보정되어야 할 색상 요소에 대한 매핑 테이블(mapping table)을 생성하였다. 생성된 매핑 테이블은 기존 3DTV 시스템의 출력부에 3D 색상 보정 모듈로써 추가하도록 하여 일반 2D 재생 시에는 입력영상이 바이패스(bypass)되도록 하고, 3D 재생 시에는 본 논문에 의한 3D 색상 보정용 매핑 테이블을 통해 색상 보정 과정을 수행하도록 하여 3D 재생 시에도 2D에서 느낄 수 있는 색감을 재현할 수 있도록 하였다.