• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2016년도 추계학술대회
• /
• pp.527-530
• /
• 2016

본 논문에서는 $0.35-{\mu}m$ standard CMOS 공정에서 낮은 전력을 소모하면서 낮은 전원전압에서 동작하는 곡률보상 기능을 갖는 기준전류/전압 발생 회로를 제안한다. 제안된 회로는 weak-inversion 영역에서 동작하는 MOS 트랜지스터들을 사용함으로써 1V 이하 전원전압에서 동작할 수 있다. 시뮬레이션 결과는 제안되는 곡률보상 기술을 사용하여 기존의 곡률보상 기능이 없는 BGR 회로들처럼 종 모양이 아닌 사인 곡선과 같은 모양을 나타내 작은 TC 값을 보여준다. 제안된 회로들은 모두 0.9V의 전원전압에서 동작한다. 먼저, 기준전압 발생 회로는 176nW 전력을 소모하며, 온도 계수는 $26.4ppm/^{\circ}C$이다. 기준전류 발생 회로는 194.3nW 전력을 소모하며, 온도 계수는 $13.3ppm/^{\circ}C$이다.

• 대한기계학회논문집
• /
• 제16권12호
• /
• pp.2407-2414
• /
• 1992

본 연구에서는 정온도 열선식 공기유량계의 전체적인 회로를 구성한 다음, 여 기에 간단한 온도보상시스템을 첨가함으로써 유동온도의 변화에 관계없이 일정한 출력 이 나오도록 하고, 이에 관련된 온도보상시스템의 메카니즘을 규명하고자 한다. 온 도보상시스템은 여러 가지가 알려져 있으나, Drubka(1977)가 열선브릿지에 단지 온도 센서(thermistor)를 삽입하고, 과열비(overheat ratio), 열선의 냉저항과 작동 중의 저항차, 열선의 브릿지상단에서의 출력 중 한 가지를 일정하게 유지시켜 온도보상을 수행하는 방법을 제안하였다. Takagi(1985)는 위의 방법 중 과열비를 일정하게 유지 시키는 방법을 택하고, 출력으로 브릿지상단의 전압이 아닌 열선에 흐르는 전류를 감 지함으로써 더욱 더 간단한 온도보상시스템을 제안하였다. 본 연구는 바로 이 방법 을 채용하여 온도보상을 수행한다.

• Journal of Power Electronics
• /
• 제19권1호
• /
• pp.190-200
• /
• 2019

The flyback converter, which can be regarded as a nonlinear time-varying system, has complex dynamics and nonlinear behaviors. These phenomena can affect the stability of the converter. To simplify the modeling process and retain the information of the output capacitor branch, a special sampled-data model of a peak current-mode (PCM) controlled flyback converter is established in this paper. Based on this, its dynamic behaviors are analyzed, which provides guidance for designing the circuit parameters of the converter. With the critical stability boundary equation derived by a Jacobian matrix, the stable operation range with a varied output capacitor, proportional coefficient of error the amplifier, input voltage, reference voltage and slope of the compensation ramp of a PCM controlled flyback converter are investigated in detail. Research results show that the duty ratio should be less than 0.5 for a PCM controlled flyback converter without ramp compensation to operate in a stable state. The stability regions in the parameter space between the output capacitor and the proportional coefficient of the error amplifier are enlarged by increasing the input voltage or by decreasing the reference voltage. Furthermore, the ramp compensation also can extend to the stable region. Finally, time-domain simulations and experimental results are presented to verify the theoretical analysis results.

• 대한방사선기술학회지:방사선기술과학
• /
• 제46권4호
• /
• pp.325-336
• /
• 2023

The purpose of this study was to analyze the structural relationship between job satisfaction levels felt during ultrasound examination of radiological technologists (RTs) using a structural equation model. The subjects were a total of 203 RTs currently working in medical institutions. The method was conducted as a survey study using a questionnaire consisting of a total of 29 questions consisting of demographic characteristics and job satisfaction levels that were self-efficacy, job competency, extrinsic compensation, and job satisfaction. The reliability was secured with the Cronbach's alpha coefficient of 0.6 or higher. For statistical analysis, a significant difference between the frequency analysis of demographic characteristics and the mean of the job satisfaction levels were performed by independent sample T-test and one-way analysis of variance (ANOVA) followed by Scheffe's post hoc test. The correlation analysis between variables was tested with Spearman's and Pearson's correlation coefficient. We analyzed the structural relationships between variables by structural equations. As a result, first, job competency and extrinsic compensation had a positive effect on job satisfaction on ultrasound examination of RTs. Second, the self-efficacy of ultrasound examination RTs showed a high correlation with job competency. Third, the job satisfaction levels showed in the order of job competency, job satisfaction, self-efficacy, and extrinsic compensation. In conclusion, this study are expected to be provided as data to identify factors that could improve job satisfaction during ultrasound examination of RTs by empirically analyzing the structural relationship of self-efficacy, job competency, and external compensation.

• 한국정밀공학회지
• /
• 제17권4호
• /
• pp.135-141
• /
• 2000

The major role of temperature sensors in thermal error compensation system of machine tools is improving machining accuracy by supplying reliable temperature data on the machine structure. This paper presents a new method for fault diagnosis of temperature sensors and recovery of faulted data to establish the reliability of thermal error compensation system. The detection of fault and its location is based on the correlation coefficients among temperature data from the sensors. The multiple linear regression model which is prepared using complete normal data is also used fur the recovery of faulted data. The effectiveness of this method was tested by comparing the computer simulation results and measured data in a CNC machining center.

• 센서학회지
• /
• 제17권3호
• /
• pp.223-228
• /
• 2008

A more accurate method of measuring the electrical conductivity (L) of solutions was developed by applying dynamic temperature compensation for measurement of L. Temperature changes of a sample were induced by a heater probe and the changes in L per unit temperature were measured. An equation for L with respect to temperature change was developed and L at the standard temperature ($25^{\circ}C$) was computed. Based on our proposed method, it is possible to have temperature compensation without having the temperature coefficients in advance.

• 센서학회지
• /
• 제24권4호
• /
• pp.270-273
• /
• 2015

One of the main problems when working the chemical sensor is the lack of repeatability and reproducibility of the sensor response. If the problem is not properly taken into consideration, the stability and reliability of the system using chemical sensors would be decreased. In this paper we analyzed the sensor's drift of short term and proposed a compensation method for reducing the effects of the drift in order to improve the stability and the reliability of the chemical sensor. The sensor drift was analyzed by a trend line graph and CV(coefficient of variation) was used to quantify. And we compensated for the drift by using the internal normalization. As a result it was found that the value of CV was decreased after compensation.

• Journal of Electrical Engineering and Technology
• /
• 제3권3호
• /
• pp.444-449
• /
• 2008

This study aims at compensation of the skin moisture level using skin impedance and SR factor. SR factor is related with the current diffusion into the skin layer. To efficiently analyze the current diffusion on the skin model, we used an electromagnetic simulation program called Ansys 10.0 Emag. We confirmed that the measured value decreases as the electric current gets more diffused to the layer below the horny layer. In order to conduct actual experiments based on the simulated result, we manufactured special electrodes with 24 pins by arranging 0.8mm-diameter electrodes every 0.5mm, in a $3{\times}8$ array. By simultaneously achieving both impedance value and SR value of skin with the manufactured electrodes, we compared the skin moisture level using the existing equipment to the skin moisture level applied using the skin impedance as well as the SR factor developed in this study. The correlation coefficient between the skin moisture level achieved from the existing equipment and the reference value was 0.615 (p<0.01), whereas the correlation coefficient between the skin moisture achieved from the regression equation in this study was 0.677 (p<0.01). Accordingly, it was confirmed that applying SR factor additionally improves the moisture level more precisely.

• ETRI Journal
• /
• 제37권1호
• /
• pp.43-53
• /
• 2015

In this paper, a selective coefficient updating (SCU) approach at each branch of the per-tone equalization (PTEQ) structure has been applied for insufficient cyclic prefix (CP) length. Because of the high number of adaptive filters and their complex adaption process in the PTEQ structure, SCU has been proposed. Using this method leads to a reduction in the computational complexity, while the performance remains almost unchanged. Moreover, the use of set-membership filtering with variable step size is proposed for a sufficient CP case to increase convergence speed and decrease the average number of calculations. Simulation results show that despite the aforementioned algorithms having similar performance in comparison with conventional algorithms, they are able to reduce the number of calculations necessary. In addition, compensation of both the channel effect and the transmitter/receiver in-phase/quadrature-phase imbalances are achievable by these algorithms.

• 한국광학회지
• /
• 제15권6호
• /
• pp.485-489
• /
• 2004

색 분산과 색 분산 경사를 보상하기 위하여 결합 계수가 파장 축을 따라 첩 된 순 위상 샘플링 광섬유 Bragg 격자를 제안하였다. 기존의 샘플링 주기의 첩과 결합 계수의 첩을 동시에 이용하여 동일한 파장 다중 채널들의 대역폭들을 얻을 수 있었다.