• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.11a
• /
• pp.305-308
• /
• 2004

There are ground facility of maintenance in house electric facility of infra maintenance electric home appliances having used multifariousness in house, that use electric energy of common source for equipment. The body of building such as the reinforced concrete construction is structurally united, and the electric resistance is also small. It is possible that those foundations have contacted the ground at large surface area and that it substitutes the building construction body for the earth electrode. This is called "the structure earthing". This method has been defined at electrical facilities technical standards and KS in our country, and it has been used in various quarters practically. However, in our country, there is no example of using the foundation of the house as substitution earth electrode practically, and the means of the evaluation as electrode has not been established either. Then, in this paper, basic research for utilizing foundation of the house as substitution earth electrode is carried out.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.2
• /
• pp.835-840
• /
• 2011

In this study, a disk-type piezoelectric transformer was fabricated. Its diameter was 50 mm and thickness was 4.5 mm. The driving and generating electrode with their gap of 1mm were fabricated on the top surface. But the common electrode was fabricated on the whole bottom surface. The electrode surface of driving and generating part on the top surface was divided into 2, 4 and 8 pieces. The electrical characteristics with its electrode variation was measured in the range of load resistance of $100{\Omega}{\sim}10_{K\Omega}$. We investigated quantitively the influence of the set-up voltage ratio.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.707-710
• /
• 2004

We have proposed on dual-drive & -emission (DDE) panel based on organic light-emitting diodes (OLEDs). The device is composed on independent operation of two OLED structures with two transparent electrodes for data signals and an intermediate reflective electrode for common scan signal. Typical device structure is ITO / organic electroluminescent layer (1) /intermediate reflective electrode / organic electroluminescent layer (2) /transparent electrode. Symmetric bright emission could be obtained by applying AlNd as the intermediate reflective electrode and $MoO_3$ as a hole injection layer for upper device structure. The proposed panel is useful for emissive face-to-face panel exhibited for different images.

• Journal of Environmental Science International
• /
• v.19 no.8
• /
• pp.941-949
• /
• 2010

The three electrode system was used to detect the pesticide fenitrothion ($C_9H_{12}NO_5PS$. MW=277.24) using cyclic voltammetry (CV) and square wave anodic stripping voltammetry (SWASV). The working electrode was mercury immobilized on a carbon nanotube paste electrode (Hg-CNTPE). At the optimized condition, the limit of detection (LoD) was 0.6 ppt ($2.16{\times}10^{-12}\;M$), and the relative standard deviation was 0.035% (n=15). And there is more sensitive in detecting fenitrothion than common type carbon nanotube paste electrode. When it was implanted into the brain of live fish (carp), the existence of fenitrothion was measured without any destruction or damage of tissue.

• Journal of Information Display
• /
• v.5 no.3
• /
• pp.18-24
• /
• 2004

Voltage-dependent transmittance characteristics associated with various cell parameters have been studied in-plane switching liquid crystal display when both common and pixel electrodes are transparent. When both electrodes are opaque, the transmittance is related to only the distance (I) between electrodes. However, where transparent electrode is used, it is influenced not only the 1but also an electrode width (w) and rubbing angle. In addition, these factors are related to operating voltage which shows maximal transmittance. To maximize the light efficiency of the cell and obtain low operating voltage, the above-mentioned cell parameters need to be optimized.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.932-934
• /
• 2006

A relationship between discharge delay time and the aging method were investigated: A-Y (Address electrode - Scan electrode) aging and conventional X-Y(Common electrode - Scan electrode) aging with the variation of sustain voltage beyond self-erasing discharge. Although A-Y aging decreases discharge delay time, it has several drawbacks like non-uniformity of discharge, degradation of luminous efficiency and a color temperature. In a conventional aging condition which is carried out near the mid-margin voltage, discharge delay time is short in low voltage and high frequency condition. As an alternative to conventional voltage aging, high voltage aging is suggested which is carried out at self-erasing sustain voltage region. High voltage aging shows lower discharge delay time and fast aging speed than conventional voltage aging.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.16 no.10
• /
• pp.914-922
• /
• 2003

The FFS (fringe-field switching) mode was known to exhibit both a wide viewing angle and high transmittance, especially when using a liquid crystal with negative dielectric anisotropy. We have studied cell gap-dependent electrode-optic characteristics of the FFS mode using the LC with negative dielectric anisotropy. In case of a small cell gap of 2 ${\mu}$m, the transmittance at the center of pixel and common electrodes is relatively low because effect of surface anchoring that holds the LC to the initial state is larger than that in a large cell gap of 4 .urn such that the LCs in those regions cannot rotate enough. However, in case of a large cell gap of 4 .urn, the effect of surface anchoring becomes relatively small so that the LCs at the center of pixel and common electrode can be twisted enough by applied voltage, giving rise to high transmittance. Therefore, we can conclude that the light efficiency is dependent on the cell gap.

• Bulletin of the Korean Chemical Society
• /
• v.26 no.11
• /
• pp.1738-1742
• /
• 2005

In this study a novel triiodide ion-selective electrode based on a charge transfer complex of iodine and Bis(2-hydroxyacetophenone)butane-2,3-dihydrazone (ICT), as a membrane carrier was prepared. The electrode has a linear dynamic range between 1.0 ${\times}$ $10^{-2}$ and 5.0 ${\times}$ $10^{-7}$ M, with a Nernstian slope of 58. 99 ${\pm}$ 0.3 mV $decade^{-1}$ and detection limit of 3.0 ${\times}$ $10 ^{-7}$ M. The potentiometric response of the proposed sensor is independent of the pH of the solution in the pH range of 3.0-10.0. The electrode possesses the advantages of short conditioning time, fast response time, and especially, very good selectivity over a large number of common organic and inorganic anions. The electrode can be used for at least 6 months without any considerable divergences in the potentials. It was used as an indicator electrode in potentiometric titration of triiodide ion with thiosulfate.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.539-542
• /
• 2003

We have studied cell gap-dependent electrode-optic characteristics of the FFS mode using the LC with negative dielectric anisotropy. In case of a small cell gap of 2 ${\mu}m$, the transmittance at the center of pixel and common electrodes is low due to stronger influence of surface anchoring that holds the LC to the initial state than twisting force induced by neighboring LCs. In case of a large cell gap of 4 ${\mu}m$, the influence of surface anchoring force becomes weak so that the LCs at the center of pixel and common electrode can be twisted enough by applied voltage, giving rise to high transmittance. Therefore, we conclude that the light efficiency in the device is dependent on the cell gap.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1745-1747
• /
• 2000

TFT-LCD simulator, PDAST(Pixel Design Array Simulation Tool) could simulate the effect of the variation on the pixel characteristics. Since feed-through voltage in TFT-LCD can be a serious problem to pixel voltage characteristics, it should be compensated. It is applicable to various kinds of TFT-LCDs and can be used to calculate the spontaneous part of common electrode voltage accurately. Also, PDAST can estimate pixel voltage according to various inversion methods. It allows high-speed calculation and the information obtained from this study could be utilized to design the larger area and finer image quality panel.