• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.6
• /
• pp.91-98
• /
• 2013

Magnetic sensor chip for measuring bio-magnetism is implemented in $0.18{\mu}m$ CMOS technology. The magnetic sensor chip consists of a small-sized high inductance coil sensor and an instrumentation amplifier (IA). High inductance coil sensor with suitable sensitivity and bandwidth for measurement of bio-magnetic signal is designed using electromagnetic field simulation. Low gm operational transconductance amplifier (OTA) using transconductance reduction techniques is designed for on-chip solution. Output signal sensitivity of magnetic sensor chip is $3.25fT/{\mu}V$ and reference noise of 21.1fT/${\surd}$Hz. Proposed IA is designed along with band pass filters(BPF) to reduce magnetic signal noise by using current feedback techniques. Proposed IA achieves a common mode rejection ratio of 117.5dB while the input noise referred is kept below $0.87{\mu}V$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.10
• /
• pp.966-982
• /
• 2014

This paper presents recent trends in system-level EMC investigation and countermeasure technology for radio frequency interference (RFI) influenced by noise generated in high-speed digital system. Recently, as the only digital device can perform various roles, there are a variety of EMI/EMC problems between systems. Especially, RFI is now recognized as a major problem, which occurs by EMI caused by the digital system. Therefore, in this paper, recent trends of RFI investigation from component-level to system-level are introduced and analyzed. Furthermore, in order to solve the RFI problem, recent researches are presented and investigated for the occurrences and suppression methods of common-mode noise which is one of the major noise sources in high-speed digital system. Lastly, this paper suggested future research of system-level EMC analysis and countermeasure technology for RFI problems.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.8
• /
• pp.35-41
• /
• 2012

As automation equipment and electronic device progresses, the importance of power quality is more increasing. This paper represents the analysis and suppression about the causes of trouble by the inverter's ON/OFF noise in plant in order to prevent damage resulting in a secondary damage to conduct precise diagnosis and effective noise reduction. The countermeasure as a reduced carrier frequency and the LC resonant filter had been applied and confirmed the effective results to solve the trouble of noise.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.452-457
• /
• 1998

This paper deal with problems of leakage current, shaft voltage, bearing current, and EMI, in valiable-speed AC drives. The originating mechanism is illustrated with a high-frequency equivalent circuit. Reduction methods are classified in to six categories based on the equivalent circuit. Some experimental results show that a common-mode transformer (CMT) and a common-noise canceler (ACC) can solve the problems, which have been proposed the authors.

• Journal of Power Electronics
• /
• v.14 no.6
• /
• pp.1197-1207
• /
• 2014

Common-mode voltage (CMV) causes overvoltage stress to winding insulation and damages AC motors. CMV with high dv/dt causes leakage currents, which create noise problems for equipment installed near the converter. This study proposes a new pulse-width modulation (PWM) strategy for three-level T-type NPC inverters. This strategy substantially eliminates CMV. The principle for selecting suitable triangle carrier signals for the three-level T-type NPC is described. The proposed method can mitigate the peak value of CMV by 50% compared with the phase disposition pulse-width modulation method. Furthermore, the proposed method exhibits better harmonic spectrum and lower root mean square value for the CMV than those of the reduced-CMV method on the basis of the phase opposition disposition PWM scheme with modulation index higher than 0.5. The proposed modulation can easily be implemented using software without any additional hardware modifications. Both simulation and experimental results demonstrate that the proposed carrier phase-shift PWM method has good output waveform performance and reduces CMV.

• Journal of the Institute of Convergence Signal Processing
• /
• v.9 no.4
• /
• pp.280-287
• /
• 2008

For the reduction of common-mode noise level in Indirect-contact ECG (IDC-ECG) measurement a driven-right-leg grounding method was a lied to the IDC-ECG. Because the IDC-ECG does not require any direct contact between the electrodes and the human skin. it is adequate for un-constraining long-term ECG measurement at home and its various applications are now under development. However, larger 60 Hz noise induced by power line a ears in IDC-BCG than in conventional ECG, that is a restriction of IDC-ECG a application. In this study, the driven-right-leg ground which has been used in conventional direct-contact ECG, was adapted to the IDC-ECG measurement by feedback of the inversion of amplified common-mode noise to the body through the conductive fertile laid on the chair seat By this study, indirect-contact driven-right-leg ground was developed and it was shown to work stably. It was shown that the level of 60Hz power line noise was reduced to about -40 dB when the driven-right-leg gain was 1000. This study shows that we can extend the upper limit of the frequency band of IDC-ECG to 100Hz from 30Hz which is conventional upper limit in IDC-ECG, and we can raise the ground impedance between the body and conductive textile. So it is expected that the application area of the IDC-ECG will be extended by the results of this study.

• Nuclear Engineering and Technology
• /
• v.56 no.4
• /
• pp.1532-1537
• /
• 2024

Time-of-flight (TOF) PET detectors with fast-rise-time scintillators and fast-single photon time resolution silicon photomultiplier (SiPM) have been developed to improve the coincidence timing resolution (CTR) to sub-100 ps. The CTR can be further improved with an optimal bandwidth and minimized electronic noise in the readout circuit and this helps reduce the distortion of the fast signals generated from the TOF-PET detector. The purpose of this study was to develop an ultra-high frequency and fully-differential (UF-FD) readout circuit that minimizes distortion in the fast signals produced using TOF-PET detectors, and suppresses the impact of the electronic noise generated from the detector and front-end readout circuits. The proposed UF-FD readout circuit is composed of two differential amplifiers (time) and a current feedback operational amplifier (energy). The ultra-high frequency differential (7 GHz) amplifiers can reduce the common ground noise in the fully-differential mode and minimize the distortion in the fast signal. The CTR and energy resolution were measured to evaluate the performance of the UF-FD readout circuit. These results were compared with those obtained from a high-frequency and single ended readout circuit. The experiment results indicated that the UF-FD readout circuit proposed in this study could substantially improve the best achievable CTR of TOF-PET detectors.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.4
• /
• pp.59-64
• /
• 2023

In this paper, It is proposed through the empirical design of a Conducted EMI filter for noise reduction of power used in electronic devices. For the proposed structure, A-type, B-type, C-type, and D-type structures were designed, and conductive noise reduction was confirmed by using an LC network with various X-capacitors, Y-capacitors, and Air-inductors. 10 [μH] was used for L1 and L2, and 4.7 [nF] was used for C1 and C2. L3 for common mode used 13[μH], and C5, C6, C7 were designed using 10[nF]. The measured insertion loss values of the designed EMI filter were -74.4[dB] at 3.2MHz, -75.4[dB] at 4MHz, and -75.3[dB] at 13.56MHz. Therefore, the proposed EMI filter will be able to reduce power supply noise used in various electronic devices.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.4
• /
• pp.372-376
• /
• 2012

The most common type of the piezoelectric energy harvester is the cantilevered beam since it is attached to the host structure and tuned to the frequency of the base excitation easily. However, the excessive strain at the fixed end of cantilevered beam causes some problems such as fatigue and durability. The use of higher vibration modes of the cantilevered beam may reduce the concentration of the strain at the fixed end since the strains of higher modes are distributed along the span. The results show that the use of high vibration mode is not efficient for power generation, but it reduces the excessive strain lever at typical region to prevent the failure by fatigue.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.9 s.100
• /
• pp.957-963
• /
• 2005

This paper presents technique of wideband TIA for optical communication systems using TSMC 0.25 ${\mu}m$ CMOS RF-Mixed mode. In order to improve bandwidth characteristics of an TIA, we use active inductor shunt peaking to cascode and common-source configuration. The result shows the 37 mW and 45 mW power dissipation with 2.5 V bias and 61 dB$\Omega$ and 61.4 dB$\Omega$ transimpedance gain. And the -3 dB bandwidth of the TIA is enhanced from 0.8 GHz to 1.45 GHz in cascode and 0.61 GHz to 0.9 GHz in common-source. And the input noise current density is $5 pA/\sqrt{Hz}$ and $4.5 pA/\sqrt{Hz}$, and -10 dB out put return loss is obtained in 1.45 GHz. The total size of the chip is $1150{\times}940{\mu}m^2$.