• Journal of the Korean Society of Safety
• /
• v.21 no.3 s.75
• /
• pp.73-80
• /
• 2006

Generally beam design depends on the yielding and maximum strength of each member varying with its section shape. Web plate of H-shape beam has not been substituted with glass plate, because it is known that its strength and heat properties are different and it is limited to substitute the existing steel web with glass element. Ceiling height of each room should be decreased with more than 60-80cm due to the beam. Differently from this condition, glass web beam has a good point to see through it and sunshine can be penetrate into the other size especially when it is installed as of outside wall. And also, it can be safer due to controlling room inside easier, if the strength is applicate. This study is to show some applicability after finding out the properties using the test. The test members with a size of $1,600{\times}200{\times}300{\times}9mm$ being SS41 rolled steel having THK 9mm flange while having 8,10mm and reinforced glass 12mm thickness is bonded with epoxy bond under the condition of temperature $28^{\circ}C$, humidity 50%, bonding power 24Mpa. It is show reinforced glass has 5 times of fracture stress more than the common glass but $50{\sim}150%$ difference between these 2 kinds of glass was shown. Reinforce glass did not support the original upper flange after fracture but the common glass did the upper flange after unloading. Generally reinforced glass is stronger than the common one but the common glass having a part of crack on it, compared with reinforced glass having the overall fracture could be more useful in case of needing ductility.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1106-1111
• /
• 2006

To improve warpage, delamination and the chemical reaction between 2 different co-fired materials, the bonding behavior with common glass was studied. As shown in the previous paper, the phenomenon of the infiltration is different with the composition of the glass. In particular, in the case of low temperature melting glass, infiltration is experimented in this study. GA-1 glass is infiltrated among $BaTiO_3$ particles below $800^{\circ}C$ and is made by glass/ceramic composite. Until the laminate is fired under $850^{\circ}C$, provskite phase is observed. Although in the case of GA-12 glass, the temperature of the glass infiltration is lower than it of GA-l glass, the perovskite phase already disappears at $800^{\circ}C$. As a result, GA-1 and GA-12 glasses are infiltrated among particles at low temperature, however, the chemical reactivity of the glass/ceramic and sintering temperature should be considered.

• Resources Recycling
• /
• v.29 no.3
• /
• pp.51-60
• /
• 2020

This study was carried out to get the optimum conditions for manufacturing high refractive glass beads from waste fluorescent lamp glass. Chemical composition, X-ray diffraction pattern, particle size distribution, refractive index of glass beads, and the effect of air mixing ratio and ejection rate were investigated. The obtained results are as follows. The X-ray diffraction pattern and chemical composition of glass beads made of waste fluorescent glass are similar to common glass except ReO₂ 0.0108 wt%, BaO 0.071 wt%, NiO 0.0039 wt% and CaO 7.8 wt% but 11.7 wt% of common glass. The glass beads made of waste fluorescent lamp glass have the narrower particle size distribution of and the higher refractive index than the glass beads made of common glass. The optimal conditions of kiln operation for manufacturing glass beads from waste fluorescent lamp glass are 20 m/sec of ejection rate, 1.7 of air mixing ratio, and 940℃ of temperature.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1209-1210
• /
• 2006

A novel sintering process is proposed for bonding of $BaTiO_3$ and $Al_2O_3$ layers. Common commercial glass was used and infilterated among filler particles. As the kind of commercial glass, the phenomenon of the infilteration is different. Although Sud-1140 glass forms a glass/filler composite, it is not completely infilterated into the filler particles at $900^{\circ}C$. However as the increase of sintering temperature the infilteration of glass was improved. In this study, GA-1 and GA-12 glasses were infilterated the more than Sud-1140 glass. However, they are reacted by $BaTiO_3$ layer. The results of the experiment show that constrained sintering and the co-firing of the different materials were possible for glass infilteration using Sud-1140 glass at $1000^{\circ}C$.

• Conservation Science in Museum
• /
• v.30
• /
• pp.71-88
• /
• 2023

This paper examined the visible characteristics and chemical composition of glass beads from the Joseon Dynasty as well as the associations thereof. It also explored the characteristics and uses of glass beads by region. This study covered a total of 1,819 pieces excavated from 25 locations in the Gyeonggi, Chungcheong, and Gyeongsang regions, of which 537 pieces were analyzed for their chemical composition. Glass beads of the Joseon Dynasty take a variety of shapes such as a Round, Coil, Floral, Segmented, Flat, Oval, and Calabash. Colors vary from shades of brown (brown, lemon yellow) and shades of blue (Bluish-Green, greenish-Blue, Purple-Blue) to shades of white (colorless, white) and shades of green (Green, Greenish-Blue, Greenish-Brown). Brown accounts for the largest percentage, followed by Bluish-Green, greenish-Blue. It was identified that Drawing technique was the most common glass bead production technique of the Joseon Dynasty. Potassium oxide (K₂O) was the most common flux agent for glass beads, while the potash glass and mixed alkali glass groups account for the largest quantity. The choice of stabilizers depended on the type of flux agents used, but the most common were calcium oxide (CaO) and aluminum oxide (Al₂O₃). The potash glass and potash lead glass groups are high in CaO and low in Al₂O₃, the mixed alkali glass group is high in CaO, and the lead glass group is low in CaO. In terms of the association between color and shape, most of the beads with shade of brown and blue have round shapes of brown and blue have spherical shapes, while the coil shape is prominent in blue beads. A high percentage of green and colorless beads also take the shape of a coil, while white beads in general have a floral shape. In terms of the association between shape and chemical composition, round, floral and segmented shapes account for a high percentage of the potash glass group, while coil and flat shapes are common in the mixed alkali glass group. This paper also analyzed the colorants for each color based on the association between color and chemical composition. Iron (Fe) was used as the colorant for brown and white, and titanium (Ti) and iron were used for light yellow. Purple-Blue was produced by by cobalt (Co), and greenish-Blue, Bluish-Green, green, Greenish-Blue were produced by iron and copper (Cu). Colorless beads had a generally low colorant content.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2022.11a
• /
• pp.648-649
• /
• 2022

Glass is a common object in living environments, but even humans are sometimes unable to identify it. This study proposes a method for detecting glass area by learning edge information from images. The network structure of Transformer is used to accept the base features extracted by backbone and extract the boundary information of RGB images, and both features are used to learn the features of glass area and determine the glass area based on these boundary features. The experimental results show that our proposed method can detect glass area in images.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.34 no.2
• /
• pp.318-335
• /
• 2010

This study is to enhance the competitiveness of the domestic cosmetic industry and provide basic materials needed for a design idea by analyzing perfume bottles designed by Rene Lalique. The methods of this study are documentary research and demonstrative research. The documentary research considered the theoretical background with a focus on related domestic and international literature, previous research, and Internet materials. The demonstrative research extracted photo materials of the bottle designs of Lalique from domestic and international web sites along with literature that classified them into shapes, colors, materials, and patterns that analyzed the general characteristics and chronologic changes. The results of this study are as follows. The curve-oriented shape was common and multi-colors were used more frequently than a single color in the 1910's. Colorless-transparent glass and a flower patterns were used frequently for materials and patterns, respectively. Lalique reflects this style in his bottle designs because the Art Nouveau effect in the 1910's. In the 1920's, curved and straight shapes had a similar percentage. The use of multi-colors and one type of glass bottle increased versus the 1910's. Similar to the 1910's, a flower pattern was used most frequently. This suggests that Lalique was influenced by the established Art Nouveau and was also interested in the Art Deco style, In the 1930's, an organic curved shape was common. Unlike the 1910's and 1920's, a single color was more common than multi-colors. The one type of glass bottle and a geometric pattern were common for materials and patterns, respectively. The Art Deco style was reflected in the bottle design of Lalique in the 1930's.

• KIEAE Journal
• /
• v.4 no.3
• /
• pp.27-35
• /
• 2004

The conventional way to acquire sufficient amount of daylight in interiors is to provide large openings with clear glass. The use of clear glass on the whole facade, however, might cause a sort of visual problem because of the harness of direct sun and brighter sky surface than expected. They should be filtered in opticalway or bounced in the architectural. One of the common solutions for the problem might be the use of photometric glasses with various transmittances for the glass walls. This paper deals with performance data related to the impact of various transmittal glazing materials for window systems in terms of daylighting. A series of scale model measurements was carried out with the fundamental configuration of a commonly used all-glass facades. Additionally some experimental performance index was issued for the better expression of the need of natural lighting.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2008.10a
• /
• pp.440-441
• /
• 2008

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.2
• /
• pp.124-130
• /
• 2014

In a mass manufacturing system of optical fibers, the sufficient cooling of glass fibers freshly drawn from a draw furnace is essential, asinadequately cooled glass fibers can lead to poor resin coating on the fiber surface and possibly fiber breakage during the process. In order to improve fiber cooling at a high drawing speed, it is common to use a helium injection into a glass fiber cooling unit in spite of the high cost of the helium supply. The present numerical analysis carried out three-dimensional thermo-fluid computations of the cooling gas flow and heat transfer on moving glass fiber to determine the cooling performance of glass fiber cooling depending on the method of helium injection. The results showed that afront injection of helium is most effective compared to a uniform or rear injection for reducing air entrainment into the unit and thus cooling the glass fibers at a high fiber drawing speed. However, above a certain amount of injected helium, there was no more increase of the cooling effect regardless of the helium injection method.