• 한국안전학회지
• /
• 제21권3호
• /
• pp.73-80
• /
• 2006

Generally beam design depends on the yielding and maximum strength of each member varying with its section shape. Web plate of H-shape beam has not been substituted with glass plate, because it is known that its strength and heat properties are different and it is limited to substitute the existing steel web with glass element. Ceiling height of each room should be decreased with more than 60-80cm due to the beam. Differently from this condition, glass web beam has a good point to see through it and sunshine can be penetrate into the other size especially when it is installed as of outside wall. And also, it can be safer due to controlling room inside easier, if the strength is applicate. This study is to show some applicability after finding out the properties using the test. The test members with a size of $1,600{\times}200{\times}300{\times}9mm$ being SS41 rolled steel having THK 9mm flange while having 8,10mm and reinforced glass 12mm thickness is bonded with epoxy bond under the condition of temperature $28^{\circ}C$, humidity 50%, bonding power 24Mpa. It is show reinforced glass has 5 times of fracture stress more than the common glass but $50{\sim}150%$ difference between these 2 kinds of glass was shown. Reinforce glass did not support the original upper flange after fracture but the common glass did the upper flange after unloading. Generally reinforced glass is stronger than the common one but the common glass having a part of crack on it, compared with reinforced glass having the overall fracture could be more useful in case of needing ductility.

• 한국전기전자재료학회논문지
• /
• 제19권12호
• /
• pp.1106-1111
• /
• 2006

To improve warpage, delamination and the chemical reaction between 2 different co-fired materials, the bonding behavior with common glass was studied. As shown in the previous paper, the phenomenon of the infiltration is different with the composition of the glass. In particular, in the case of low temperature melting glass, infiltration is experimented in this study. GA-1 glass is infiltrated among $BaTiO_3$ particles below $800^{\circ}C$ and is made by glass/ceramic composite. Until the laminate is fired under $850^{\circ}C$, provskite phase is observed. Although in the case of GA-12 glass, the temperature of the glass infiltration is lower than it of GA-l glass, the perovskite phase already disappears at $800^{\circ}C$. As a result, GA-1 and GA-12 glasses are infiltrated among particles at low temperature, however, the chemical reactivity of the glass/ceramic and sintering temperature should be considered.

• 자원리싸이클링
• /
• 제29권3호
• /
• pp.51-60
• /
• 2020

본 연구는 폐형광등을 사용하여 고굴절 유리비드를 제조하기 위한 최적 조건 도출을 위해 진행되었다. 제작된 유리비드는 XRD 분석과 더불어 물리·화학적 분석을 통해 유리비드의 굴절률 및 공기혼합비율, 방출속도에 따른 영향을 조사하였다. 연구를 통해 얻어진 결과는 다음과 같다. 형광등 재활용유리로 제작된 글라스 비드와 일반 재활용 유리로 제작된 글라스비드 시료를 XRF 분석결과 일반 재활용 유리로 제작한 글라스비드에 CaO가 11.7 wt% 함유되 있는 반면 형광등 재활용 유리로 제작한 글라스비드에는 CaO 7.8 wt% 함량 비중과 비교해 3.9 wt% 함량 비중이 더 높은 것으로 분석되었다. 또한 형광등 재활용 유리로 제작된 글라스비드에는 일반 재활용 유리로 제작한 글라스비드에 함유되지 않은 ReO₂ 0.0108 wt%, BaO 0.071 wt%, NiO 0.0039 wt% 가 함유되어 있는 것을 알 수 있었다. 일반 재활용 유리로 제작된 글라스 비드와 폐형광등을 재활용하여 유리로 제작된 글라스비드의 Refractive Index 비교 시 폐형광등으로 제작된 유리비드가 일반 재활용 유리로 제작된 글라스비드보다 더 작은 입자 크기분포와 높은 굴절률을 갖는 것을 알 수 있었다. 결론적으로 폐형광 등 재활용 유리를 구상 형태의 글라스비드로 제작하기 위하여 Kiln 방식의 공정에서는 공기 혼합비율 1.7, 화염온도조건 940℃ 20 m/sec 조건에서 가장 높은 생성율을 확인할 수 있었다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1209-1210
• /
• 2006

A novel sintering process is proposed for bonding of $BaTiO_3$ and $Al_2O_3$ layers. Common commercial glass was used and infilterated among filler particles. As the kind of commercial glass, the phenomenon of the infilteration is different. Although Sud-1140 glass forms a glass/filler composite, it is not completely infilterated into the filler particles at $900^{\circ}C$. However as the increase of sintering temperature the infilteration of glass was improved. In this study, GA-1 and GA-12 glasses were infilterated the more than Sud-1140 glass. However, they are reacted by $BaTiO_3$ layer. The results of the experiment show that constrained sintering and the co-firing of the different materials were possible for glass infilteration using Sud-1140 glass at $1000^{\circ}C$.

• 박물관보존과학
• /
• 제30권
• /
• pp.71-88
• /
• 2023

조선시대 유리구슬의 가시적 특성과 화학 조성을 알아보고 그에 따른 연관성을 알아보았다. 또한 권역에 따른 특성에 대하여 고찰하였다. 연구 대상은 경기, 충청, 경상권역 25개소에서 출토된 1,819점으로 이 중에서 화학 조성 분석은 537점을 실시하였다. 조선시대 유리구슬은 크게 둥근형, 코일형, 꽃잎형, 연주형, 납작형, 대추형과 표주박형 구슬 등의 형태가 나타난다. 색상은 크게 갈색계(갈색, 담황색), 청색계(청록색, 벽색, 감청색), 백색계(무색, 백색), 녹색계(녹색, 녹청색, 녹갈색) 등이 나타난다. 갈색이 가장 많은 수량을 차지하고 다음으로 청록색과 벽색이 주로 확인된다. 조선시대 유리구슬 제작기법은 대표적으로 말은 기법이 확인된다. 유리구슬의 융제는 주로 K₂O가 사용되었고, 포타쉬유리군, 알칼리혼합유리군 등이 가장 많은 수량을 차지한다. 안정제는 융제의 종류에 따라 다르긴 하나 주로 CaO와 Al₂O₃가 사용되었다. 포타쉬유리군과 포타쉬납유리군은 HCLA계, 알칼리혼합유리군은 HCA계. 이와 반대로 납유리군은 LCA계에 속한다. 색상과 형태의 연관성으로 갈색계와 청색계는 둥근형이 가장 많으며 청색계는 코일형이 두드러지게 나타난다. 녹색계와 무색계도 코일의 비중이 높고 백색은 꽃잎형의 비중이 높다. 형태와 화학 조성에 대한 연관성으로 둥근형, 꽃잎형, 연주형은 포타쉬유리군이, 코일형과 납작형은 알칼리혼합유리군의 수량이 많다. 색상과 화학조성의 연관성으로 각 색상의 착색제에 대하여 알아보았다. 갈색과 백색은 Fe, 담황색은 Ti, Fe가 착색제로 작용하였다. 감청색은 Co가, 벽색과 청록색, 녹색, 녹청색은 Fe와 Cu가 작용하였으며, 무색은 착색제의 성분함량이 대체적으로 낮은 편이다.

• 한국정보처리학회:학술대회논문집
• /
• 한국정보처리학회 2022년도 추계학술발표대회
• /
• pp.648-649
• /
• 2022

Glass is a common object in living environments, but even humans are sometimes unable to identify it. This study proposes a method for detecting glass area by learning edge information from images. The network structure of Transformer is used to accept the base features extracted by backbone and extract the boundary information of RGB images, and both features are used to learn the features of glass area and determine the glass area based on these boundary features. The experimental results show that our proposed method can detect glass area in images.

• 한국의류학회지
• /
• 제34권2호
• /
• pp.318-335
• /
• 2010

This study is to enhance the competitiveness of the domestic cosmetic industry and provide basic materials needed for a design idea by analyzing perfume bottles designed by Rene Lalique. The methods of this study are documentary research and demonstrative research. The documentary research considered the theoretical background with a focus on related domestic and international literature, previous research, and Internet materials. The demonstrative research extracted photo materials of the bottle designs of Lalique from domestic and international web sites along with literature that classified them into shapes, colors, materials, and patterns that analyzed the general characteristics and chronologic changes. The results of this study are as follows. The curve-oriented shape was common and multi-colors were used more frequently than a single color in the 1910's. Colorless-transparent glass and a flower patterns were used frequently for materials and patterns, respectively. Lalique reflects this style in his bottle designs because the Art Nouveau effect in the 1910's. In the 1920's, curved and straight shapes had a similar percentage. The use of multi-colors and one type of glass bottle increased versus the 1910's. Similar to the 1910's, a flower pattern was used most frequently. This suggests that Lalique was influenced by the established Art Nouveau and was also interested in the Art Deco style, In the 1930's, an organic curved shape was common. Unlike the 1910's and 1920's, a single color was more common than multi-colors. The one type of glass bottle and a geometric pattern were common for materials and patterns, respectively. The Art Deco style was reflected in the bottle design of Lalique in the 1930's.

• KIEAE Journal
• /
• 제4권3호
• /
• pp.27-35
• /
• 2004

The conventional way to acquire sufficient amount of daylight in interiors is to provide large openings with clear glass. The use of clear glass on the whole facade, however, might cause a sort of visual problem because of the harness of direct sun and brighter sky surface than expected. They should be filtered in opticalway or bounced in the architectural. One of the common solutions for the problem might be the use of photometric glasses with various transmittances for the glass walls. This paper deals with performance data related to the impact of various transmittal glazing materials for window systems in terms of daylighting. A series of scale model measurements was carried out with the fundamental configuration of a commonly used all-glass facades. Additionally some experimental performance index was issued for the better expression of the need of natural lighting.

• 한국대기환경학회:학술대회논문집
• /
• 한국대기환경학회 2008년도 추계학술대회 논문집
• /
• pp.440-441
• /
• 2008

• 한국기계가공학회지
• /
• 제13권2호
• /
• pp.124-130
• /
• 2014

In a mass manufacturing system of optical fibers, the sufficient cooling of glass fibers freshly drawn from a draw furnace is essential, asinadequately cooled glass fibers can lead to poor resin coating on the fiber surface and possibly fiber breakage during the process. In order to improve fiber cooling at a high drawing speed, it is common to use a helium injection into a glass fiber cooling unit in spite of the high cost of the helium supply. The present numerical analysis carried out three-dimensional thermo-fluid computations of the cooling gas flow and heat transfer on moving glass fiber to determine the cooling performance of glass fiber cooling depending on the method of helium injection. The results showed that afront injection of helium is most effective compared to a uniform or rear injection for reducing air entrainment into the unit and thus cooling the glass fibers at a high fiber drawing speed. However, above a certain amount of injected helium, there was no more increase of the cooling effect regardless of the helium injection method.