• Journal of the Korean Society of Combustion
• /
• v.2 no.1
• /
• pp.17-27
• /
• 1997

It is well known that NOx formation has a strong dependence on the maximum temperature and correspondingly with the maximum chamber pressure of a closed combustion system. However, in a case of impinging-jet-flame (IJF hereafter) combustion with opposed dual pre-chambers, low $NO_x$ formation with high pressure could be achieved, but its mechanism has not been clearly understood so far. In this study, a three-dimensional analysis is adopted to resolve time-variant local properties that might indicate the mechanism of IJF combustion. Numerical results are verified by comparing them with experiments. The IJF combustion in a vessel with no pre-chamber, with single pre-chamber, and with dual pre-chambers is studied. The orifice diameter and the volumetric ratio of pre-chamber are used as geometric parameters. The effects of main-chamber ignition delay time and combustion time of main-chamber, orifice exit velocity, orifice exit temperature, turbulent kinetic energy of main-chamber and spatial distribution of temperature in the latter stage of combustion are investigated. A longer main-chamber ignition delay and a shorter main-chamber combustion time suppress the formation of high temperature region with respect to mean temperature, which consequently results in less NO production.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.5
• /
• pp.122-134
• /
• 1995

The present study was investigated combustion characteristics of methane-air mixtures at stratified charge in a constant volume combustion chamber. The main results obtained from this study can be summarized as follows. In case of ${\phi}_s=1.0$, total burning times greatly affected rather than initial time of pressure increase and maximum combustion pressure. In case of ${\phi}_t=1.0$, initial time of pressure increase and total burning times were affected considerably in comparison with the case of ${\phi}_s=1.0$. Also, even the very lean mixture which total equivalence ratio is ${\phi}_t=0.69$(${\phi}_s=1.0$, ${\phi}_m=0.65$), by changing configuration of the critical passage-hole and using a stratified mixture, it is possible to decrease substantially the initial time of pressure increase. total burning times and NOx concentration without deteriorating combustion characteristics such as maximum combustion pressure, rate of heat release etc. in comparison with the use of single chamber(in case of ${\phi}=1.0$) only. Specifically, our trends were revealed remarkably in the case of Type D which is reduced a flame contact area of sub-chamber side of the passage-hole.

• Journal of ILASS-Korea
• /
• v.25 no.3
• /
• pp.119-125
• /
• 2020

In this paper, we used Helmholtz solver based on 3D finite element method to quantitatively analyze the effects of change of gain, time delay and time delay spread, which are the main variables of flame transfer function, on combustion instability in gas turbine combustor. The effects of the variable of flame transfer function on the frequency and growth rate, which are the main results of combustion instability, were analyzed by applying the conventional heat release fluctuation model and modified one considering the time spread. The analysis results showed that the change of gain and time delay in the same resonance mode affected the frequency of the given resonance modes as well as growth rate of the feedback instability, however, the effect of time delay spread was not relatively remarkable, compared with the dominant effect of time delay.

• 한국연소학회:학술대회논문집
• /
• 2012.11a
• /
• pp.5-7
• /
• 2012

This study presents relations between the time lag and interaction index of the impinging-jet injectors using time lag model in a model chamber. To analyze the response of the flame, 5% amplitude of oxidizer velocity is artificially perturbed at a resonance frequency. At the mixing point of fuel and oxidizer, which determines the characteristic length, the relationship between velocity perturbation and heat release rate is quantified by combustion parameters of interaction index and time lag. As the improved method to apply the time-lag, the method using the average velocity obtained from numerical results is suggested.

• Journal of ILASS-Korea
• /
• v.21 no.2
• /
• pp.104-110
• /
• 2016

Main purpose of the current paper is to show results of time lag analysis using phase information of flame transfer function in order to predict combustion instabilities in a gas turbine combustor. The flame transfer function (FTF) is modeled using a commercial Computational Fluid Dynamics (CFD) code (Fluent). Comparisons of the modeled flame shapes with the measured ones were made using the optimized heat transfer conditions and combustion models. The FTF modeling results show a quite good agreement with the measurement data in predicting the phase delay (i.e. time lag). Time lag analysis results using the phase of FTF shows better combustion instability prediction accuracy than using time lag calculated from the steady state flame length.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.3 no.1
• /
• pp.65-75
• /
• 1995

The present study was investigated combustion characteristics of methane-air mixtures at stratified charge in a constant volume combustion chamber. The results indicated that even the vety lean mixture, which is normally not flammable in single chamber type, could be burned within. a comparatively short time by using sub-chamber with stratified charge method. And the lean inflammability limit of mixture in a main chamber was about ($\phi_m$cr=O.46, when the equivalence ratio of a sub-chamber was $\phi_s$= 1.0. Initial time of pressure increase and total burning times were decreased and maximum combustion pressure. was increased as the equivalence ratio of both sub and main chamber approached unity. Specifically, initial time of pressure increase and total burning times were greatly affected rather by. the equivalence ratio of sub-chamber than that of main chamber. The maximum combustion pressure was little affected if the total equivalence ratio lies in the same range.

• Journal of the Korean Society of Safety
• /
• v.11 no.1
• /
• pp.75-83
• /
• 1996

This paper was concerned with pool fire about many used kerosene and diesel oil. In order to know the thermal effects of kerosene and diesel oil, temperature change in the pool fire of these fuels were obtained as a variation of combustion time and the tank's height and diameter by using the data acquisition system, And fuel combustion velocity were derived as a function of the diameter and wall thickness of tanks and combustion time. As a result, when the tank's height was 15㎝, the greater diameter the higher temperature rising regardless of tank's wall thickness and fuels. But, when the tank's height is 30㎝, temperature rising was not higher than 15㎝. Also, temperature rising in the pool fire of kerosene much higher than diesel oil. Kerosene's combustion velocity was about two times faster than diesel oil. And, kerosene's combustion velocity was increased according to the increasing of tank's diameter and combustion time. But, diesel oil's combustion velocity was a little increased or not. Surrounding temperature change of tank with the pool fire was obtained temperature distribution of 0∼35℃ according to the change of tank's diameter and distance from the tank's wall.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.157-163
• /
• 2011

Combustion of magnesium dust particle were fabricated test devices and combustion experiments were carried out. The ignition delay time were measured in change of magnesium particle mass flow rate in premixed flame. According to increasing magnesium particle mass flow rate, ignition delay time were more shorter. In addition, magnesium dust combustion temperature were measured different particle sizes and o/f ratio by two wavelength pyrometry. Dust combustion flame temperature is almost similarly, through to equivalence ratio, confirm the combustion flame temperature range characteristics.

• Journal of ILASS-Korea
• /
• v.26 no.3
• /
• pp.142-148
• /
• 2021

The objective of this study is to analyze the basic flame behavior characteristics using the single fuel droplet combustion of diesel, palm-based biodiesel, and canola-based biodiesel. The results were compared and analyzed through the post processed image, which was applied the threshold level for removing noise in the raw image. The raw image was taken by a high-speed camera during the entire combustion process. At the same time, the maximum flame length, which was measured by the application code of the MATLAB program, the ignition delay, and the combustion period were compared and analyzed.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.8 no.3
• /
• pp.150-156
• /
• 1975

This paper dealt itself with the relation of the heat release rate with crank angle in combustion process by adjusting the injection time, injection amount and engine speed of diesel engine. The result of test were obtained by analyzing indicator diagram of KUBOTA 2LKE diesel engine, where the indicator was used Tertronix oscilloscope. The combustion period of diesel engine is composed of premixed burning time and combustion controlled time. The larger the premixed burning region, the higher efficiency was obtained with the higher maximum pressure than at the time of the normal smooth operation. The longer the combustion controlled time, the lower the maximum pressure than the period of the normal operation, but the efficiency was decreased. The region of premixed burning was principally controlled by injection delay, but combustion controlled time was affected when oxygen and fuel were mixed. Efficiency of engine was increased at the time of earlier injection time under the constant injection amount, and engine speed, but the pressure increasing was observed higher than the efficiency increasing.