• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.7
• /
• pp.891-898
• /
• 2011

The present work was conducted to get the best geometric information for the optimum design of the complex heat exchanger. The objective function for optimal design was expressed as a combination of pressure drop and heat transfer rate. The geometric parameters for the variables of louver pitch and height, tube width, etc., were limited to ranges set by manufacturing conditions. The optimum geometric parameters were calculated by using empirical correlations and theory. The sensitivity of the parameters and optimum values are shown and discussed. The weighting factor in the objective function is important in the selection of the louver fin-tube heat exchanger.

• Advances in aircraft and spacecraft science
• /
• v.5 no.4
• /
• pp.411-430
• /
• 2018

This computational study examines the augmentation of classic 2-D Rayleigh-$B{\acute{e}}nard$ convection by the addition of periodically-spaced transverse fins. The fins are attached to the heated base of the cavity and serve to partition the cavity into 'units' with different aspect ratios. The respective impacts upon heat transfer of the fin configuration parameters - including spacing, height, thickness and thermal conductivity - are systematically examined through numerical simulations for a range of laminar Rayleigh numbers (0 < Ra < $2{\times}10^5$) and reported in terms of an average Nusselt number. The selection of the low Rayleigh number regime is linked to likely scenarios within aerospace applications (e.g. avionics cooling) where the cavity length scale and/or gravitational acceleration is small. The net heat transfer augmentation is found to result from a combination of competing fin effects, most of which are hydrodynamic in nature. Heat transfer enhancement of up to $1.2{\times}$ that for a Rayleigh-$B{\acute{e}}nard$ cavity without fins was found to occur under favorable fin configurations. Such configurations are generally characterized by short, thin fins with half-spacings somewhat less than the convection cell diameter from classic Rayleigh-$B{\acute{e}}nard$ theory. In contrast, for unfavorable configurations, it is found that the introduction of fins can result in a significant reduction in the heat transfer performance.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.45 no.2
• /
• pp.180-182
• /
• 2012

A single juvenile specimen of $Thunnus$ $alalunga$ (8.4 mm in standard length) of the Scombridae was collected from the southeast sea of Jeju Island ($127.7^{\circ}E$, $33.0^{\circ}N$) on August 18, 2011. It was identified as $T.$ $alalunga$ based on the following combination of morphological characters: snout elongated; melanophores focused on the dorsal spiny region, but no melanophores on the dorsal soft fin base, anal fin base or caudal region.

• Proceeding of EDISON Challenge
• /
• 2015.03a
• /
• pp.500-509
• /
• 2015

This paper presents the single objective design optimization of plate-fin heat sink equipped with fan cooling system using Genetic Algorithm. The proper heat sink and fan model are selected based on the previous studies. And the thermal resistance of heat sinks and fan efficiency during operation are calculated according to specific design parameters. The objective function is combination of thermal resistance and fan efficiency which have been taken to measure the performance of the heat sink. And Decision making procedure is suggested considering life time of semiconductor and Fan Operating cost. And also Analytical Model used for optimization is validated by Fluent, Ansys 13.0 and this model give a quite reasonable and reliable design.

• CDE review
• /
• v.21 no.2
• /
• pp.39-49
• /
• 2015

This paper presents the single objective design optimization of plate-fin heat sink equipped with fan cooling system using Genetic Algorithm. The proper heat sink and fan model are selected based on the previous studies. And the thermal resistance of heat sinks and fan efficiency during operation are calculated according to specific design parameters. The objective function is combination of thermal resistance and fan efficiency which have been taken to measure the performance of the heat sink. And Decision making procedure is suggested considering life time of semiconductor and Fan Operating cost. And also Analytical Model used for optimization is validated by Fluent, Ansys 13.0 and this model give a quite reasonable and reliable design.

• Journal of Power System Engineering
• /
• v.10 no.4
• /
• pp.11-16
• /
• 2006

This research is to verify the cooling effect of the acting surface on the rotary motor using heat pipe and conventional cooling fan. In order to show the cooling performance of the rotary motor and heat pipe with the fin-typed heat sink, the surface temperature of the motor and condenser was measured in real time. The experiments were also conducted as for not only cooling device installed with heat pipe only, but with heat pipe and conventional cooling fan simultaneously. The present experiment reveals that the cooling combination of the heat pipe and cooling fan is far superior to the conventional cooling device for the driving motor such as the fin-typed heat sink. When the driving voltage of 20V and 14V were supplied to the driving motor, the cooling performance of the rotary motor with heat pipe was 170% and 500%, respectively better than that without heat pipe on steady state condition.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.22 no.3
• /
• pp.353-359
• /
• 2019

In this study, a aerodynamic loads prediction to design a deploying device of folded fin was introduced. In general, resultant flow conditions around the fin are used to obtain deploying moments and required energy. However, when it comes to the air vehicles launched from a mobile platform, more specific flow conditions can be provided. With the conditions, the design criteria can be calculated more realistically. In this study, therefore, aerodynamic moments induced by aerodynamic loads and energy required in deployment were calculated using wind-over-deck(WOD) velocity, combination of a platform velocity and a wind velocity. For the calculation, wind tunnel test was conducted on various angle of attack, side slip angles, and folding angles. It was found that the aerodynamic moments and the energy required in deployment using the non-uniform flow due to the velocity components were less than those using the uniform flow without the components.

• Proceedings of the SAREK Conference
• /
• 2003.07a
• /
• pp.33-33
• /
• 2003

• Korean Journal of Environmental Biology
• /
• v.38 no.1
• /
• pp.106-113
• /
• 2020

This study identified the differences in the morphometric characteristics of the truss and classical dimensions between diploid and triploid Far Eastern catfish, Silurus asotus, and provided methods for sorting diploid and triploid Far Eastern catfish based on morphometric observations. The significant variables were the direct distance between the anterior edge of the lower lip and the anterior insertion of the dorsal fin(DALAD), the horizontal distance between the anterior edge of the lower lip and the anterior insertion of the ventral fin (HALAV), the direct distance between the anterior edge of the upper lip and the first nostril(DAUF), the direct distance between the anterior edge of the upper lip and the second nostril(DAUS), the interorbital width(IW), and the mandible barbel length (ManBL). The more significant variables were HALAV, DALAD, DAUF, IW, and DAUS. The most useful combination of variables for separating the two groups was DALAD, IW, and DAUF, which correctly classified 85% of the catfish as triploid or diploid, and that percentage was the maximum degree of value possible (p<0.05). Triploid Far Eastern catfish had a high rate of growth in the head region and body depth during the first year after hatching. Triploid Far Eastern catfish had smaller heads and shorter mandible barbels than diploid Far Eastern catfish.

• Fisheries and Aquatic Sciences
• /
• v.20 no.10
• /
• pp.26.1-26.9
• /
• 2017

Fishes in genus Sardinella are small pelagic species, which plays an important role in marine ecosystem as the first consumer. Those species are also commercially important, whose total catch reaches 278,600 tons in 2011 in Indonesia, but their identification has been difficult for their morphological similarity. In this study, we reported Sardinella jussieu for the first time in Indonesian coastal area (Banten Bay, Indonesia, $6^{\circ}\;0^{\prime}\;50.00^{{\prime}{\prime}}\;S-106^{\circ}\;10^{\prime}\;21.00^{{\prime}{\prime}}\;E$). We were able to confirm the species by both its morphological characteristics including the black spot at dorsal fin origin, the dusky pigmentation at caudal fin, 31 total scute numbers, and DNA sequence identity in the GenBank database by the molecular analysis. Its total mitochondrial genome was determined by the combination of next-generation sequencing and typical PCR strategy. The total mitochondrial genome of Sardinella jussieu (16,695 bp) encoded 13 proteins, 2 ribosomal RNAs, 22 transfer RNAs, and the putative control region. All protein-coding genes started with ATG and typical stop codon and ended with TAA or TAG except for ND4 in which AGA is used. Phylogenetic analyses of both COI region and full mitochondrial genome showed that S. jussieu is most closely related to Sardinella albella and Sardinella gibbosa