• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.184-184
• /
• 2009

Lead-free Piezoelectric $[Li_{0.04}(Na_{0.44}K_{0.56})](Nb_{0.88}Ta_{0.1}Sb_{0.02})$ (abbreviated as NKNLTS) has been synthsized by conventional mixed oxide method traditional ceramics process without cold-isostatic pressing. Effect of $Bi_2O_3$ addition on NKNLTS ceramics was investigated. Piezoelectric properties of the ceramic were varied with the amount of $Bi_2O_3$ addition and showed the maximum Kp value at 0.4wt% $Bi_2O_3$ addition. The results show that the optimum poling condition for NKNLTS ceramics of 3.5kV/mm, poling temperature of $120^{\circ}C$ and poling time of 30min. At the sintering temperature of $1100^{\circ}C$ and the calcination temperature $800^{\circ}C$, the optimal values of density=$4.7g/cm^2$, Kp=0.44, $\varepsilon_r$=1309 were obtained. Consequently, lead free piezoelectric ceramics with the excellent piezoelectric could be fabricated using a conventional mixed oxide process and the optimal manuacturing condition of those was obtained.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 2002.05a
• /
• pp.227-234
• /
• 2002

With the increasing environmental consideration and stricter regulations, gasification of waste is considered to be more attractive technology than conventional incineration for energy recovery as well as material recycling. The experiment for combustible waste mixed with plastic and cellulosic materials was performed in the fixed bed gasifier to investigate the gasification behavior with the operating conditions. Waste pelletized with a diameter of 2~3cm and 5cm of length was gasified at the temperature range of 1100~145$0^{\circ}C$. It was shown that the composition of H$_2$ was in the range of 30~40% and CO 15~30% depending upon oxygen/waste ratio. Casification of waste due to thermoplastic property from mixed plastic melting and thermal cracking shows a prominent difference from that of coal or coke. It was desirable to maintain the top temperature up to foot to ensure the mass transfer and uniform reaction through the packed bed. As the bed height was increased, the formation of H$_2$ and CO was increased whilst $CO_2$ decreased by the char-$CO_2$ reaction and plastic cracking. From the experimental results, the cold gas efficiency was around 61% and heating values of product gases were in the range of 2800~3200㎉/Nm3.

• Journal of Environmental Science International
• /
• v.7 no.3
• /
• pp.335-348
• /
• 1998

The intensive meteorological observations including pibal balloon at Ungcheon, airsonde and 10m meteorological tower observations at Gulup-Do, where are located In the western coastal region, are taken to Investigate the characteristics of the upper and lower atmospheric structure and the local circulation pattern during the period of 17 to 22 September 1996. The diurnal variations of weather elements(i.e. air temperature, humidity, pressure, and Und speeds at Gulup-Do are analyzed and discussed with those at four inland meteorological stations. The vertical profiles of wind vector, ortho- gonality(Ω), and shear obtained from the pibal obsenrations are also presented to examine the change of wand structure according to the synoptic-scale pressure system's movement. The diurnal temperature changes at Gulup-Do are more sensitive than that of Inland meteorological stations In case of the mow of southwesterlies but are not dominant due to the ocean effect under the Influence of relatively cold northerlies. A well defined mixed layer Is developed from the 500m to the maximum 1700m with a significant capping Inversion layer on the top of it. It can be found from the vertical profiles of wind vector that the wind become generally strong at the interface heights between cloud lay- ers and non-cloud layers. The maximum Und shear Is appeared at the bel각t where the varlauon of wand direction Induced by the passage of synoptic-scale pressure system Is accompanied with the In- crease of Und speed. Based on the wind orthogonality, the change of wind direction with height is more complicated In cloudy day than In clear day. In case of a fair weather, the change of wand direction is showed to be at around 2km.

• Ocean and Polar Research
• /
• v.28 no.3
• /
• pp.245-258
• /
• 2006

We investigated seasonal variations of the upper ocean temperature and the mixed layer depth (MLD) in an eddy-permitting global ocean general circulation model (OGCM) to assess the OGCM perfermance. The OGCM is based on the GFDL MOM3 which has a horizontal resolution of 0.5 degree and 30 vertical levels. The OGCM was integrated for 68 years using a monthly-mean climatological wind stress forcing. The model sea surface temperature (SST) and sea surface salinity were restored to the Levitus climatology with a time scale of 30 days. Annual-mean model SST shows a cold bias $(<\;-2^{\circ}C)$ in the summer hemisphere and a warm bias $(>\;1^{\circ}C)$ in the winter hemisphere mainly due to the restoring boundary condition of temperature. The model MLD captures well the observed features in most areas, with a slightly deep bias. However, in the Ross Sea and Weddell Sea, the model shows significantly deeper MLD than the climatology-mainly due to weak salinity stratifications in the model. For amplitude of seasonal variation, the model SST is smaller $(1{\sim}3^{\circ}C)$ than the observation largely due to the restoring surface boundary condition while the model MLD has larger seasonal variation $({\sim}50m)$. It is suggested that for more realistic simulation of the upper ocean structure in the present eddy-permitting ocean model, more refinements in the surface boundary condition for the thermohaline forcing and parameterization for vertical mixing are required, together with the incorporation of a sea-ice model.

• International Journal of Highway Engineering
• /
• v.19 no.2
• /
• pp.17-24
• /
• 2017

PURPOSES : This study aims to develop a sealant for use in the installation of Weigh-In-Motion (WIM) sensor for asphalt concrete or cement concrete pavements. METHODS : In order to investigate the properties of various sealants that were mixed with latex and carbon fiber, various test methods were adopted, such as bituminous bond strength test, softening point test, and cone penetration test. To evaluate moisture susceptibility, the BBS test was conducted under moist condition. The bond strength ratio (BSR) was calculated based on tensile strength ratio method. RESULTS : The sealant's properties significantly varied according to the amount of latex or carbon fiber. The usage of latex marginally enhanced the cone penetration test result, notwithstanding reduced asphalt content. This implies that the sealant will be proper cold temperature reason. Moreover, the addition of latex and carbon fiber evidently increased the softening point. This indicates that the tendency of the material to flow at elevated temperatures is encountered during service. With the addition of latex and carbon fiber, the moisture susceptibility measured with BSR improved marginally, while the bond strength under dry condition decreased marginally. Sealant F displays the highest bond strength and BSR under limited test conditions. CONCLUSIONS : According to the proportion of latex and carbon fiber mixed, properties of sealant, such as softening point, cone penetration, and BSR varied marginally. This indicates that the sealant has to be applied considering the environmental condition, to improve service life.

• Journal of Powder Materials
• /
• v.21 no.3
• /
• pp.196-201
• /
• 2014

In this study, nanocrystalline Cu-Ni bulk materials with various compositions were cold compacted by a shock compaction method using a single-stage gas gun system. Since the oxide layers on powder surface disturbs bonding between powder particles during the shock compaction process, each nanopowder was hydrogen-reduced to remove the oxide layers. X-ray peak analysis shows that hydrogen reduction successfully removed the oxide layers from the nano powders. For the shock compaction process, mixed powder samples with various compositions were prepared using a roller mixer. After the shock compaction process, the density of specimens increased up to 95% of the relative density. Longitudinal cross-sections of the shock compacted specimen demonstrates that a boundary between two powders are clearly distinguished and agglomerated powder particles remained in the compacted bulk. Internal crack tended to decrease with an increase in volumetric ratio of nano Cu powders in compacted bulk, showing that nano Cu powders has a higher coherency than nano Ni powders. On the other hand, hardness results are dominated by volume fraction of the nano Ni powder. The crystalline size of the shock compacted bulk materials was greatly reduced from the initial powder crystalline size since the shock wave severely deformed the powders.

• Korean Journal of Head & Neck Oncology
• /
• v.10 no.2
• /
• pp.91-101
• /
• 1994

Nodular thyroid disease is a common clinical problem. The problem in clinical practice is to distinguish malignant or potentially malignant tumor from harmless nodules. The cases of thyroid nodule surgically managed at Department of General Surgery, Soon Chun Hyang Univ. Hospital during the period Jan. 1985 to July. 1992 were reviewed retrospectively. To assess method of distinguishing malignant from benign lesions of the thyroid gland, we reviewed 162 patients with thyroid nodule. There were 61(37.7%) malignant nodules and 101(62.3%) benign nodules. According to the review, distinguishing the benign from the malignant nodule with history, physical examination, clinical manifestation, and duration of illness was not suggested sufficiently. In ultrasonogram of 73 cases, 57.5% of nodules were solid, 20.6% were cystic, 21.9% were mixed solid and cystic. Of these, 28.5% of the operated solid lesions, 12.5% of the mixed lesions, and only 6.7% of the cystic lesions were malignant. Thyroid scanning of 82 cases revealed cold nodules in 60 patients(73.2%), of which 26 cases were malignant(36.6%) 137 patients underwent fine needle aspiration cytology(FNAC), and these results were as follow: sensitiviey was 70.6%, specificity was 93.0%, false-positive rate was 14.3%, and false-negative rate was 15.8%. 41 patients underwent frozen biopsy, and the results as follow: sensitivity was 80.0%, specificity was 89.7%. Neither scintigraphy nor ultrasonogram has sufficient specificity to distinguish benign from malignant nodule. But FNAC and frozen biopsy have sufficient accuracy to differentiate benign from malignant nodule. In the benign nodules, the most common type of operation was total lobectomy (60.4%). Of the malignant nodules, total thyroidectomy with or without modified radical neck dissection was performed in 30 cases(49.2%). We conclude that the single technique used to determine the differential diagnosis of a thyroid nodule are unrealiable. It is therefore essential to combine all avaiable clinical and laboratory information.

• Nuclear Engineering and Technology
• /
• v.33 no.4
• /
• pp.355-364
• /
• 2001

In order to evaluate and finally optimize the vitrification condition for combustible dry active waste (DAW), dust and gas generation characteristics were investigated for PE, cellulose, and mixed waste Tests were conducted by varying the operation variables such as melter configuration, excess oxygen amount, and waste feeding rate. Results showed that dust generation characteristics were affected by the operation parameters and the melter＇s configuration is the dominant one. For all tested DAWs, dust generation was reduced by increasing the waste feeding rate and the excessive oxygen amount in the melter. Among waste types, dust amount was decreased by the order of mixed wastes, PE, and cellulose. Other parameters such as temperature variation and operation time have also affected the dust generation. The optimum condition for the DAW vitrification was determined as the melter＇s configuration equipped for minimizing the waste dispersion with 20 kg/h of waste feeding rate and 100% of excessive oxygen supply. CO gas concentration in the off-gas was immediately influenced by the combustion state in the melter, but showed similar trend as the dust generation. For the NOx production during the vitrification process, thermal NOx, which is generated from the Post Combustion Chamber (PCC), rather than fuel NOx was assumed to be dominant. The gas cleaning of efficiencies of the PCC, wet scrubber, and Selective Catalytic Reduction system (SCR) were found to be high enough to keep the concentration of pollutants (CO, NOx, SOx, HCI) in the stack below their relevant emission limits.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.11a
• /
• pp.543-546
• /
• 2000

Ferroeleclric 0.05PZN-xPZT(90/10)-(0.95-x)PZT(10/90) (x=0.65, 0.85) specimens were fabricated by the mixed-oxide method and cold-pressing method using sol-gel derived PZT(90/10) and PZT(10/90) powders. All specimens show a uniform ferroelectric grain without the presence of the pyrocholre phase. Average grain size increased with an increase in sintering temperature, the value for the x=0.65 specimen sintered at 125$0^{\circ}C$ was 14.4$\mu$m. The dielectric constant and dielectric loss of the x=0.65 specimen sintered at 125$0^{\circ}C$ were 1247, 2.06%, respectively. All specimens showed fairly good temperature and frequency stability of dielectric constant with the range from -2$0^{\circ}C$ to 6$0^{\circ}C$ and 100Hz to 10MHz. The coercive field and the remanent polarization of x = 0.65 specimen sintered at 125$0^{\circ}C$ were 8.5 kV/cm and 13 $\mu$C/cm$^2$, respectively. The pyroelectric coefficient of the x=0.65 specimen sintered at 125$0^{\circ}C$ was 5.64$\times$10$^{-8}$ C/cm$^2$K, respectively.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.6
• /
• pp.30-35
• /
• 2013

To conserve wood resources for papermaking, chemical compositions of the hemp (Cannabis sativa L.) bast fiber cultivated in Korea such as holocellulose, ${\alpha}$-cellulose, lignin, alcohol-benzene extractives, hot and cold water extractives, and ash contents were investigated to manufacture the specialty packaging paper effectively. Significantly very low klason lignin content of 3.3% was accomplished by removing of the outer shell of bark. Laboratory soda pulping method which is very useful for the nonwood fiber was adapted, and it was found that there was no significant difference in both kappa number and H-factor between 25% and 30% NaOH charge. Hemp pulp cooked with the laboratory digester in 25% NaOH at $170^{\circ}C$ were mixed together with the wood pulp(NBKP:LBKP=1:1) in order to find the optimum mixture ratio which exhibited acceptable paper strength properties such as tensile index, burst index, and tear strength. When 10% of hemp soda pulps was mixed with 90% of wood pulps comprised of SwBKP and HwBKP (1:1), all physical strength increased significantly. The physical strength decreased as the amount of hemp pulp increased because the cell wall of bast fiber is very thick which causes low conformability and low fiber-fiber bonding. These results showed that paper made of hemp-wood pulp can be used for the specialty packaging paper which requires both the characteristic surface properties and the high physical strength of hemp fiber.