• Asian-Australasian Journal of Animal Sciences
• /
• v.16 no.1
• /
• pp.96-99
• /
• 2003

The objective of this study was to evaluate the effects of various organic acids on microbial characteristics and Salmonella typhimurium in pork loins. Fresh pork loins were sprayed with various organic acids such as lactic acid, citric acid and acetic acid at various concentrations (0.5, 1, 1.5 and 2%). After spraying, the samples were packaged by HDPE film under air and stored at $4^{\circ}C$ for 14 days, and analyzed. Microbial deterioration of pork loins during the aerobic cold storage was delayed by organic acid spray. The bactericidal effect of acids increased with the increasing concentration. However, the inhibitory activity of organic acids during the storage varied with the kinds and concentrations of the acids. As for total plate counts, acetic acid was found to have the highest bactericidal activity, whereas citric acid was found to be the most inhibitory for coliform and S. typhimurium.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.41-45
• /
• 2009

The small-sized bi-propellant thruster using a high concentrated hydrogen peroxide and kerosene as the oxidizer and fuel was designed and fabricated in this study. The water cold-flow test was performed to verify the performance characteristics of the injector. The mixing head assembly used in this model thruster was designed as a structure to combine igniter, injectors and film cooling, which are capable of regulating each mass flowrate. This maximize the experimental verification and efficiency of the design optimization. Finally, the mass flowrate and spray pattern of injector were evaluated by the hydraulic test. Therefore, the design validity of the mixing head was verified.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.3
• /
• pp.1-8
• /
• 1999

Mixing efficiency of the unlike Impinging split triplet injector(FOOF type) were measured to investigate the effect of the momentum ratio variation. $H_2$O/kerosene were used as a propellant simulant. The maximum mixing efficiency occured at the momentum ratio 1.5 (total mixture ratio 1.89). Calculated mixing efficiency of real propellant LOX/Kerosene showed similar trend but maximum efficiency of characteristic velocity occurs at the momentum ratio 2.0(total mixture ratio 2.17). Although there exist a little discrepancy between calculated mixing efficiency based on simulant cold test and hot fire test results, this calculated mixing efficiency can be used to predict hot fire mixing efficiency.

• Journal of ILASS-Korea
• /
• v.16 no.2
• /
• pp.76-81
• /
• 2011

A fuel injection system which is operated with a real vehicle driving simulation was developed as an alternative to a vehicle test for the fuel injectors. The sensor signals that are supplied to the ECU were measured and recorded as a data file for a vehicle driven in FTP-75 mode in a chassis dynamometer. The imperative sensor signals of the throttle position, vehicle speed, engine speed, crank position, cam position, intake air flow, and cooling water and intake air temperature were reconstructed using FPGA DAQ boards and a PXI computer. The scanning results showed good agreement with the input signals that were reconstructed. The ECU HILS system operated successfully to drive six fuel injectors, which injected fuel in the same pattern as if they were mounted in the vehicle driven in FTP-75 mode. Also, the fuel injection system developed in this research shows the possibility of application in evaluating the characteristics of fuel injection rate for injectors according to properties of injected fuel with the real driving mode of vehicles.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.123-123
• /
• 2011

알루미늄은 경량 금속으로 부식 저항력이 높아 철을 부식으로부터 보호하기 위한 표면처리 소재로 사용되고 있다. 철의 부식을 방지하기 위해서 알루미늄을 코팅하는 경우, 코팅 방법은 용융도금법이 주로 사용되고 있으며, 알루미늄을 빛의 반사막으로 활용하는 경우 진공 중에서 물리기상증착(physical vapor deposition; PVD)법을 사용하기도 한다. 알루미늄 박막을 물리기상 증착으로 코팅하면 박막성장 초기에 핵(nucleus)을 형성하고, 형성된 핵을 중심으로 주상정(column)으로 박막이 성장하는 것이 일반적이다. 알루미늄 박막의 주상정과 주상정 사이에 공극(pore)이 존재하기 때문에 알루미늄 박막을 부식방지 막으로 이용하기 위해서는 두께를 증가시켜야 한다. 본 연구에서는 스퍼터링(unbalanced magnetron sputtering)을 이용하여 치밀한 조직을 갖는 알루미늄 박막을 코팅할 수 있는 공정변수를 도출하고, 치밀한 알루미늄 조직이 철의 부식에 미치는 영향을 평가하였다. 기판은 냉연강판(cold rolled steel sheet)이 사용되었으며, 알루미늄 타겟의 크기는 직경 4 inch이었다. 알루미늄 박막의 미세조직과 밀도에 영향을 주는 공정변수를 확인하기 위해서 스퍼터링 파워, 공정 압력, 외부 자기장 세기 등의 조건을 변화시켜 코팅을 실시하였다. 알루미늄 박막의 밀도 변화에 가장 큰 영향을 준 공정변수는 외부 자기장의 세기와 방향이었다. 알루미늄 박막이 약 3 ${\mu}m$의 두께로 코팅된 냉연강판을 염수분무시험(salt spray test, 5% NaCl)으로 부식특성을 평가한 결과, 시험을 시작한 후 120시간 후에도 적청이 발생하지 않았다. 이러한 결과는 기존의 동일한 두께를 갖는 알루미늄이 코팅된 강판의 내부식 특성의 2배의 성능을 보여준다.

• Journal of ILASS-Korea
• /
• v.22 no.4
• /
• pp.185-189
• /
• 2017

In Korea, sales of passenger cars using diesel and LPG fuels were continuously increased in recent years. From now on 2030, the registrated vehicles will close in about twenty five million in Korea. From these reason, Investigation on the comparison of exhaust emission characteristics of passenger cars using LPG and Diesel fuel in variation of driving mode and ambient conditions were conducted in this study. Exhaust emission characteristics of test vehicles were measured and analyzed by using chassis dynamometer and emission analyzer. Also, test vehicles were selected on the diesel vehicle with 1.7L engine and LPG vehicle with 2.0L engine. In order to study on emission characteristics according to driving cycles, CVS-75, NEDC, US06, SC03, Cold-FTP and HWFET were applied and the test conditions were set up the cases of A/C on and hot start. From these results, it is revealed that the NOx emission of diesel vehicle was higher than that of LPG vehicle and the case of CO emission shows the opposite patterns. In the HC emission, the emission increasing patterns not showed but the NOx emission of diesel vehicle and CO emission of LPG vehicle were showed the variation patterns according to the various driving modes.

• Journal of ILASS-Korea
• /
• v.14 no.4
• /
• pp.184-189
• /
• 2009

Recently, ultrafine particles emitted from internal combustion engine is main concern because of its well known adverse health effects. So Europe decided to start the regulation about diesel engine particle number emissions. The nanoparticles smaller than 50nm in diameter have the ability to penetrate deep into interstitial tissue of luge, where they may cause severe respiratory inflammation and acute pulmonary toxicity. Recent studies have showed that spark ignition engines emit particles number concentration comparable to those from diesel engines with DPF under high load and rich mixture conditions, including cold starts and acceleration. So this study investigated emission characteristics of ultrafine particles according to fuel injection type in gasoline vehicles and LPG vehicles. The test vehicles were tested on CVS-75 and NEDC vehicle test mode using the chassis dynamometer, CPC system applied as a particle measuring instrument at the end of dilution tunnel. As a result, the correlation between fuel injection type and particulate emission was determined. GDI vehicle emitted 10 times higher particles than PFI vehicles, and compared to Mixer and LPGI type LPG vehicle, LPLI vehicle emitted particles high.

• Journal of ILASS-Korea
• /
• v.23 no.2
• /
• pp.66-73
• /
• 2018

Volatile organic compounds (VOCs) are well known as ozone precursors from photochemical reactions and contribute to the formation of photochemical smog which pose health hazards. Also, some of these compounds directly affect the human health due to their toxicity such as benzene. In this study, NMVOCs composition in exhaust gas from recreational vehicle (RV) and (MPV) were characterized using a chassis dynamometer. The results for NMVOCs have reported that alkanes emission was higher than alkenes, aromatics and cycloalkanes due to reactive of diesel oxidation catalysts. The NMVOCs composition according to carbon number was highly distributed between C3 and C6~C8. During the engine cold start condition, NMVOCs emission was higher compared to the engine hot start condition due to the increased catalytic activity. The NMVOCs emission with DPF increased compared to that without DPF. The results of this study will be provide to calculate VOCs emissions from mobile source.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.225-232
• /
• 2003

With an aim placed on its exploitation on practical injector design, liquid phase mixing due to unlike split triplet impinging element is experimentally investigated by a series of cold tests. Non-reacting kerosene/water spray simulates the kerosene/LOX propellant combination. Measurements of local mixture ratio distribution were made for different injection configurations and different momentum ratios. Mixing and mixing controlled characteristic velocity efficiencies are measured in terms of oxidizer/fuel jet momentum ratio from 0.5 to 8. Extent of mixing and its influence on hot performance are estimated in terms of mixing efficiency and mixing controlled characteristic velocity. Envelope of design locus for optimum mixing quality and corresponding maximum hot performance are proposed. Effects of momentum ratio, orifice diameter ratio and jet velocity ratios are also presented and discussed.

• Aerospace Engineering and Technology
• /
• v.5 no.2
• /
• pp.37-46
• /
• 2006

The outside environment is very severe while aircraft is cruising. Especially small particle of icing in cold air condition can have negative influence on aircraft performance. If ice particle is attached to leading edge of wing, it can change wing configuration and decrease flight quality. If icing particle is attached to inlet of engine, it can damage compressor blade and have negative influence to aircraft safety. We make icing simulation device with liquid air system for analyzing about variation of engine performance due to incoming of icing to engine.