• 한국가스학회지
• /
• 제26권4호
• /
• pp.27-35
• /
• 2022

LPG는 공기보다 무거워 지표면으로 가라앉는 특징이 있으며, 주변 공기가 체류하는 경우 증기운을 형성하기 쉬워 가스 누출로 인한 피해가 가중될 우려가 있다. 그러므로 증기운 형성에 따른 주변 지역의 영향 범위분석을 통해 피해를 예방할 필요가 있다. 본 연구에서는 LPG 공급 관리소가 설치된 제주 하가리 일대를 대상으로 토지이용 현황과 지형적 특성으로 생성되는 야간 시간대의 찬공기 흐름과 그에 따른 LPG 누출 특성을 고려하여 주변 지역으로의 피해 영향 범위를 분석하였다. KLAM_21을 활용하여 찬공기 흐름을 분석한 결과, 지형 영향으로 인해 남동쪽에서 약 2 m/s의 찬공기가 유입되었다. LPG 누출 특성은 ALOHA를 이용하였으며 찬공기 흐름을 고려하여 분석하였다. 풍속 2 m/s 조건에서 누출공 크기가 10 cm일 때 LEL 60 %(12,600 ppm)에 해당하는 범위는 61 m로 나타났으며 LPG 누출 시 증기운에 의한 화재 등의 사고가 발생하는 경우 누출원으로부터 50 m 부근에 위치한 인근 주거지에 피해가 미칠 것으로 예상되므로 사고 예방을 위한 대안책이 요구된다. 해당 연구결과는 LPG 누출로 인한 사고 발생 시 예방책을 마련하는데 기초 자료로 활용될 수 있으며 FLACS와 같은 CFD 모델링을 통해 비교적 좁은 영역에서의 LPG 누출 형상 및 증기운으로 인한 피해 영향 범위를 확인할 필요가 있다.

• 한국가스학회지
• /
• 제22권3호
• /
• pp.7-12
• /
• 2018

화석연료를 연소할 때 연소로 내의 고온의 온도 분위기에서 열적 질소산화물이 발생하게 된다. 연소기기에서 질소산화물을 저감하기 위한 여러 가지 방법 중에 배기가스 재순환 방법이 널리 쓰이고 있다. 본 연구에서는 배기가스 재순환 배관에 코안다 노즐을 사용하고 양쪽 출구가 트인 재순환하는 버너에 대하여 냉간 유동 특성을 전산유체해석을 통해 살펴보았다. 재순환 배관이 원통 버너의 접선방향으로 설치되어 있어서 버너 내부에서 선회유동이 형성되어 원통 버너 중심 부분에 역류가 생기는 현상을 관찰하였으며 이는 한쪽이 막힌 재순환 버너와 유사한 경향임을 확인 하였다. 본 연구로부터 양쪽 출구가 트인 재순환 버너에서 재순환 유입량은 한쪽이 막힌 버너보다 약 5% 증가하는 것을 확인하였고 양쪽 트인 버너에서 배기가스 재순환 배관의 유입구 위치의 출구에서는 전체 영역에서 유입 유동이 형성되고 반대편의 출구에서는 총 유량은 배출되지만 원통의 가운데 부분은 역류가 일어나는 것을 확인하였다. 배출되는 출구에서 배출되는 유량은 유입되는 출구에서의 유입량보다 3~5배 유량이 크게 나타났다.

• 한국재료학회지
• /
• 제29권5호
• /
• pp.336-341
• /
• 2019

The gas adsorption isotherm requires accurate measurement for the analysis of porous materials and is used as an index of surface area, pore distribution, and adsorption amount of gas. Basically, adsorption isotherms of porous materials are measured conventionally at 77K and 87K using liquid nitrogen and liquid argon. The cold volume calibration in this conventional method is done simply by splitting a sample cell into two zones (cold and warm volumes) by controlling the level sensor in a Dewar filled with liquid nitrogen or argon. As a result, BET measurement for textural properties is mainly limited to liquefied gases (i.e. $N_2$ or Ar) at atmospheric pressure. In order to independently investigate other gases (e.g. hydrogen isotopes) at cryogenic temperature, a novel temperature control system in the sample cell is required, and consequently cold volume calibration at various temperatures becomes more important. In this study, a cryocooler system is installed in a commercially available BET device to control the sample cell temperature, and the automated cold volume calibration method of temperature variation is introduced. This developed calibration method presents a reliable and reproducible method of cryogenic measurement for hydrogen isotope separation in porous materials, and also provides large flexibility for evaluating various other gases at various temperature.

• 한국자동차공학회논문집
• /
• 제19권4호
• /
• pp.114-120
• /
• 2011

Fuel reforming technology for the fuel cell vehicles has been frequently applied to internal combustion engine for the reduction of engine out emissions. Since syngas which is reformed from fossil fuel has hydrogen as a major component, it has abilities to enhance the combustion characteristics with wide flammability and high speed flame propagation. In this paper, syngas was feed to a 2.0 liter SI engine with MPI to improve exhaust emissions under cold start and early state of idle condition. Syngas fraction is varied to 0%, 10%, 25%, with various ignition timings. Exhaust emission characteristics and the exhaust system temperature were measured to investigate the effects of syngas addition on cold start. Result showed that HC emission could be dramatically reduced due to the fact that syngas has $H_2$ and no HC as components. The amount of $NO_x$ emission was decreased with the increase of syngas fraction. Because the dilution effect of $N_2$ and the retard of ignition timing reduces the peak combustion temperature inside the cylinder. Exhaust gas temperature was lower than that of gasoline feeding condition. Retarded ignition timing, however, resulted in increased exhaust gas temperature approximated to gasoline condition. It is supposed that the usage of syngas in an SI engine is an effective solution to meet the future strict emission regulations.

• 대한금속재료학회지
• /
• 제49권3호
• /
• pp.221-230
• /
• 2011

The cold spray process is an emerging technology that utilizes high velocity metallic particles for surface coating. Metallic powder particles are injected into a converging-diverging de Laval nozzle and accelerated to a high velocity by a supersonic gas flow. The cold spray process normally uses a circular nozzle that has a rather narrow spraying range. To overcome this fault, a slit nozzle was considered in this study. The slit nozzle is anticipated to reduce the coating process time because it has a wider coating width than the circular nozzle. However, the slit nozzle can reduce the coating efficiency because it does not allow as much gas and particle velocity as the circular nozzle. To improve the coating efficiency of a slit nozzle, the shape of the slit nozzle was modified. And the results of gas flow and particle behaviour according to the nozzlers shape were compared by the a numerical analysis. As a results, as Expansion Ratio(ER) of 7.5 was found to be the most optimal condition for enhancing the spraying efficiency when the ER was changed by the variation of nozzle neck and exit size.

• 수산해양교육연구
• /
• 제13권2호
• /
• pp.132-145
• /
• 2001

The cold discharge from LNG(liquefied natural gas) terminal makes the water temperature around the terminal fall down. This temperature reduction may result in serious changes on marine ecosystem of the coastal area. The numerical model experiments of material transport and tidal circulation in the inner bay, Chinhae Bay are investigated in the dispersion of cold discharge from LNG terminal. The condition of ambient water is exposed to tide, tidal current and cold discharge temperature. Simple numerical model experiments highlight the importance of tidal circulation and cold discharge at each case and some results are discussed. The results of this study can be used as the guideline for the site selection of LNG terminals and long-term marine environmental impact assessment.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.233-234
• /
• 2006

LNG is extremely cold, $-160^{\circ}C$ in its liquid state. When it vaporizes, returning to its natural state (re-vaporization), it cools its surroundings. This is cold energy. The manufacturing of liquid air is the first processes developed as the most effective utilization of LNG cold. In this paper, adopting the LNG cold process for manufacturing liquid air was developed and analysed. The result showed that as the higher air pressure and adapting nitrogen precooling, liquefaction rate and cumulative mass was increased.

• 한국수소및신에너지학회논문집
• /
• 제31권2호
• /
• pp.259-264
• /
• 2020

In this study, comparison study has been performed between two-stage compression and a vapor-recompression refrigeration cycle and a liquefaction using LNG cold heat. When using a first method using two-stage compression and a refrigeration cycle, at least three compressors are required, however when using LNG cold heat, no compressor is required since carbon dioxide can be pumped after condensing with the heat exchange with -160℃ of LNG. Through this study, we can save more than one hundred million KRW annually by using LNG cold heat instead of using gas compression and refrigeration cycle.

• 한국정밀공학회지
• /
• 제23권7호
• /
• pp.101-107
• /
• 2006

Cold gas dynamic spray or cold spray is a novel manufacturing method for coatings. Cold spray is a high rate and direct material deposition process that utilizes the kinetic energy of particles sprayed at high velocity (300-1,200m/s). In this research, a technique to repair the damaged mold by cold spray deposition and mechanical machining was proposed. An aluminum 6061 mold with three-dimensional surface was fabricated, intentionally damaged and material-added by cold spray, and its original geometry was re-obtained successfully by Computer Numerical Control (CNC) machining. To investigate deformation of material caused by cold spray, deposition was conducted on thin aluminum plates ($100mm{\times}100mm{\times}3mm$). The average deformation of the plates was $205{\sim}290{\mu}m$ by Coordinate Measurement Machine (CMM). In addition, the cross section of deposited layer was analyzed by scanning electron microscopy (SEM). To compare variation of hardness, Vickers hardness was measured by micro-hardness tester.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.860-864
• /
• 2001

Today's industrialized plants are required to reduce SOx emitted from stacks at factories, utility power stations, etc. For this purpose, flue gas desulfurization (FGD) system is installed and gas-gas heater (GGH) is used to play a vital role to reheat the wet treated gas from FGD. The sector plates are located at cold and hot sides of gas gas heater. They serve as sealing to prevent mixing treated and untreated gases. Therefore, the deformation of the sector plate due to its dead weight and gas pressure should be considered as major factor for the sector plate design.