• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 A
• /
• pp.202-205
• /
• 1995

Developed controller is the part of deflection yoke winding machine which controls the power to form the deflection yoke coil into desired shape after winding. So as to form the deflection yoke coil, it is needed to melt the bonding material which is spreaded on the coil. The heat melt the bonding material which is produced by flowing the current through the winded coil. Therefore, at first it is needed to peel off the enamel from the winded coil so as to flow the current, and then supply the power to produce the heat which form the winded coil into desired shape. Naturally developed controller is composed of the peeling part and the conduction and forming part. All of them consist of the inverter structure and control the output current. The peeling is achieved by low voltage and high AC current, the conduction and forming is by DC current. Developed controller also has a function that detect the resistance of the deflection yoke coil to prevent the damage of the load which is produced by poor peeling.

• 한국안전학회지
• /
• 제21권1호
• /
• pp.53-58
• /
• 2006

This paper has been addressed on the discharge characteristics of the ignition coil by Weibull function. It analyzed discharge number and amount of discharge using Weibull distribution to know the inter-relationship between partial discharge and mileage. We detected the discharge which happens for 10 seconds. The applied voltage increased by 0.5[kV] at discharge inception voltage. We diagnosed failure rate using the shape parameters. As a result, we confirmed that the failure rate was increased, because the shape parameter showed the value of 5 according to increasing mileage degradation. Also, it is considered to increase the degradation of inner insulator of ignition coil. Because failure rate of virgin was increased from 0[%] to 25[%] after degradation, stability analysis of the ignition coil using Weibull analysis is possible.

• 대한조선학회논문집
• /
• 제45권3호
• /
• pp.303-308
• /
• 2008

The induction heating is more efficient for a plate bending because of its easy operation and control of working parameters, compared with the heating by a gas torch. The existing axis symmetric analysis method could neither handle initial curved plates nor be used in the optimization of coil shapes because of its limit of an axis symmetric coil shape. But the proposed method using some discrete part models and analysis processes could overcome these difficulties and show more accurate results in temperatures and deflections of flat or curved plates with initial curvature than those in the existing axis symmetric analysis method. This method is composed of the multi-disciplinary analyses such as an electro magnetic analysis, a heat transfer analysis and a deformation analysis based on inherent strain approach per each step. Traditionally, the coil shape in the induction heating is circular shape and it needs the moving process along heating lines. To overcome this, the 'Long Type Coil' with some linear parallel coils was proposed. It did not need the moving process along heating lines and reduced the heating process time. The results of experiments were compared with those of the simulation.

• 한국초전도학회:학술대회논문집
• /
• 한국초전도학회 2000년도 High Temperature Superconductivity Vol.X
• /
• pp.257-261
• /
• 2000

The value of I$_c$(critical current) in HTS (High Temperature Superconductor) tape has a great influence on B${\bot}$(vertical field). Therefore, in shape design of field coil for the HTSG(High Temperature Superconducting Generator), a method to reduce the B${\bot}$ should be considered in order to maintain the stability and substantial improvement on the performance. On the basis of the magnetic field analysis, this paper deals with various field coil shape according to the iron plate to obtain small B${\bot}$ by using Biot-Savart's law, image method and 2D FEA(2 Dimensional Finite Element Analysis) considering the stress condition of HTS. Moreover, the analysis is verified by comparison with experimental results. And also this paper presents the advanced model by using 3D FEA, in which flux density at armature is calculated in 5kVA class HTSG.

• 대한치과교정학회지
• /
• 제22권1호
• /
• pp.135-146
• /
• 1992

It was the purpose of this study to analyze and compare the mechanical properties of ortho dontic open coil springs. Four variable factors were presented - wire diameter (.008", .009", .010"), lumen size (.030", .032", .036"), arch wire size and shape (.016" round, $ .016^{{\prime}{\prime}}{\times}.022^{{\prime}{\prime}}$ rect.) and alloy type (HiT II, Elgiloy, Sentalloy). The total 104 specimens were divided into 13 groups, and compression test was performed on an Instron test machine. The load deflection curve of each open coil spring was obtained, from which, the load-deflection relations, stiffnesses, percent recoveries were computed statistically. The results were obtained as follows: 1. When the lumen size of the coil spring remained constant, stiffness and percent recovery increased as the wire diameter increased. 2. When the wire diameter of the coil spring remained constant, stiffness and percent recovery decreased as the lumen size increased. 3. The effect of size and shape of arch wire on the coil spring was not statistically significant. 4. In alloy types, stiffness was the greatest in HiT II (55.21), Elgiloy (42.61) and Sentalloy (7.74) in that order. Sentalloy exhibited superior percent recovery and long range of action.

• 한국항행학회논문지
• /
• 제21권6호
• /
• pp.614-619
• /
• 2017

본 논문에서는 6.78 MHz 자기공진방식 무선전력전송 송수신 코일을 최적화하고 이에 따른 시뮬레이션 및 측정 결과를 제시하였다. 전송 효율은 시스템 형태 및 코일 크기 등 다양한 요인에 따라 영향을 받게 되므로 자기 공진형 무선전력전송의 실용화에 있어 코일 구조를 각각 송신용 헬리컬 공진코일과 수신용 평판형 스파이럴 공진코일을 구성하여 부피의 문제점을 최소화하고 원통형 형태의 무선충전형태에 맞게 코일의 크기, 공진기 내의 코일과 코일 간의 거리 등을 결정하였으며, 전자계 시뮬레이션을 통해 이를 확인하였다. 860mm 지름 상판과 600mm 떨어진 기둥의 원통형 구조에 대하여 적용 가능한 무선전력전송 코일을 설계하여 특성을 시뮬레이션하고, 제작하여 특성을 측정하였다. 시뮬레이션 특성은 ${\mid}S_{21}{\mid}$이 -0.53 dB, 효율 88 %, 측정 결과는 ${\mid}S_{21}{\mid}$이 -0.71 dB 로 효율 85 %를 나타내었다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 추계학술대회 논문집
• /
• pp.85-88
• /
• 2001

Deep drawing process, one of sheet metal forming methods, is used widely. Circular or square shape blanks are currently studied mainly. Especially, circular blank for coating case of chip condenser remains bridges when it is made out of aluminum coil. The bridge reduces Material-withdrawal-rate of aluminum coil to $60\%$. This paper proposes a no-bridge blank instead of circular blank. To get the different values of two cases, comparison circular blank with no-bridge blank is accomplished in the point of thickness strain in the vicinity of flange. In order to find optimal condition in new proposed blank, several process variables - those are blank holder shape, die shape radii, punch shape radii and blank holding force - are changed.

• 대한의용생체공학회:학술대회논문집
• /
• 대한의용생체공학회 1994년도 춘계학술대회
• /
• pp.85-87
• /
• 1994

This paper proposes a new inductance minimization scheme for a gradient system of arbitrarily selected shape. Although it is important to minimize the gradient coil inductance to reduce the current switching time, such minimization has been possible only for cylindrical or parallel biplanar coils. By using small current loops on arbitrarily selected surface as optimization elements, the inductance of the whole circuit can be minimized using the loop's self- and mutual-inductances. Wire positions can be easily derived from the loop current distribution. Preliminary studies for the design of x-directional surface gradient coil show the utility of tile proposed gradient coil design scheme.

• 비파괴검사학회지
• /
• 제23권6호
• /
• pp.622-634
• /
• 2003

This paper is concerned with a computational method for recovering a crack shape of steam generator tubes of nuclear plants. Problems on the shape identification are discussed arising in the characterization of a structural defect in a conductor using data of eddy current inspection. A surface defect on the generator tube ran be detected as a probe impedance trajectory by scanning a pancake type coil. First, a mathematical model of the inspection process is derived from the Maxwell's equation. Second, the input and output relation is given by the approximate model by virtue of the hybrid use of the finite element and boundary element method. In that model, the crack shape is characterized by the unknown coefficients of the B-spline function which approximates the crack shape geometry. Finally, a parameter estimation technique is proposed for recovering the crack shape using data from the probe coil. The computational experiments were successfully tested with the laboratory data.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 춘계 학술발표대회 개요집
• /
• pp.305-307
• /
• 2004

One set of rotor coils is required per each large generator rotor assembly, Rotors consist of two directly opposing poles. Each pole requires from 5 to 9 coils. Each coil is made up of two halves identified on the connection end. These coil halves will be joined together by butt brazing process during subsequent rotor assembly. Each half coil is made up of typically 4 to 9 layers of copper conductors. Because of Generator rotor is rotated very high speed with 3,600RPM, the quality soundness of brazed joints is very important at each coil. But, it is very difficult to be optimized non-destructive evaluation, because c-coil has the long shape and evaluation is to be done assembled condition. In this paper introduce newly developed inspection process and acceptance standards for the ultrasonic inspection of " C" coil butt braze. This inspection system is a semi-automatic ultrasonic flaw detector with data acquisition and retention capable of assessing the relative lack of bond of brazed butt joints