• 설비공학논문집
• /
• 제10권3호
• /
• pp.282-291
• /
• 1998

Heat transfer performance are studied for the turbulent flow of water in 3 smooth tube coils having ratios of coil to tube diameter of 16, 21 and 27, and a corrugated-coiled tube having a ratio of coil to tube diameter of 29, for Reynolds numbers from 8000 to 60000 and is also compared with the limited results available to data. The experiments are carried out for the fully developed turbulent flow of water in tube coils under the condition of uniform heat flux. This work is limited 0 tube coils of R/a between 10 and 30. The tube having a ratio of coil to tube diameter of 27 among the 3 smooth tube coils shows the best heat transfer performance. The performance of coiled tube best transfer performance. The performance of coiled tube with a similar curvature ratio is better for a corrugated-coiled tube(R/a=17) than for a smooth coiled tube(R/a=16). An empirical relation which correlates most of the data within $\pm$25% was also developed. Test result shows that the Nusselt number is found to be affected by a secondary flow due to curvature.

• 대한의용생체공학회:의공학회지
• /
• 제35권4호
• /
• pp.105-110
• /
• 2014

For the combination of MRI and magnetic particle hyperthermia(MPH), we investigated the relative heating efficiency with respect to the strength of the static magnetic field under which the magnetic nanoparticles are to be heated by RF magnetic field. We performed nanoparticle heating experiments at the fringe field of 3T MRI magnet with applying the RF magnetic field perpendicularly to the static magnetic field. The static field strengths were 0T, 0.1T, 0.2T, and 0.3T. To prevent the coil heat from conducting to the nanoparticle suspension, we cooled the heating solenoid coil with temperature-controlled water with applying heat insulators between the solenoid coil and the nanoparticle container. We observed significant decrease of heat generation, up to 6% at 0.3T(100% at 0T), due to the magnetic saturation of the nanoparticles of 15 nm diameter under the static field. We think MPH is still feasible at low magnetic field lower than 0.3T if stronger RF magnetic field generation is permitted.

• Journal of Advanced Marine Engineering and Technology
• /
• 제34권1호
• /
• pp.30-36
• /
• 2010

다중관식 헬리컬 코일형 가스냉각기내 $CO_2$의 열유량과 압력강하에 대해서 실험적으로 조사하였다. $CO_2$와 냉각수의 유량은 각각 0.06~0.075kg/s이고, 가스냉각기의 냉각압력은 8~10 MPa이다. $CO_2$의 열유량은 냉각수 질량유량, $CO_2$의 질량유량과 냉각압력에 비례하여 증가한다. $CO_2$의 압력강하는 냉각수와 $CO_2$의 질량유량이 감소할수록 감소하지만, $CO_2$의 냉각압력이 증가할수록 감소한다. 다중관식 헬리컬 코일형 가스냉각기내 $CO_2$의 열유량과 압력강하는 각각 이중관식 가스냉각기보다 상당히 높게 또는 낮게 나타났다. 따라서 다중관식 헬리컬 코일형 가스냉각기에 $CO_2$를 적용하는 경우에는 가스냉각기의 고효율화, 고성능화, 컴팩트화가 가능할 것이다.

• 한국자기학회지
• /
• 제23권5호
• /
• pp.166-172
• /
• 2013

본 연구는 자성유체 우퍼 스피커 내부에 위치한 보이스 코일의 입력전류에 따른 열전달 특성을 수치 해석적으로 고찰하는 것이다. 이를 위하여 일반 우퍼 스피커 및 자성유체 우퍼 스피커에 대하여 입력전류를 10W에서 50W로 10W씩 변화시켜가면서 입력전류에 따른 보이스 코일 발열 및 각 부품으로 전달되는 열전달 및 온도 특성 변화를 고찰하였다. 그 결과 우퍼 스피커에 공급되는 입력전류가 증가함에 따라 보이스 코일 온도가 선형적으로 증가하였고 자성유체 우퍼 스피커의 보이스 코일 온도가 일반 우퍼 스피커에 비하여 동일 입력 전류 40 W 기준에서 51.0 % 감소하였고, 동일 보이스 코일 발생 온도 490 K 기준에서 필요 입력전류는 42.5 % 감소하였다. 또한 보이스 코일에서 주변 부품으로 열전달은 자성유체 우퍼 스피커가 일반 우퍼 스피커에 비하여 51.7 % 증가하였다.

• 한국추진공학회지
• /
• 제24권3호
• /
• pp.59-70
• /
• 2020

본 논문에서는 기존 적층형 배관의 총 열전달 계수 경험식을 활용할 때 발생하는 한계점을 해결하고자, 외부 총 열전달 계수의 강제 대류 열전달 계수 항을 독립적으로 도출하는 간소화된 모델링을 제안하고, 이를 극저온 환경의 실험 결과로 확인하였다. 액체 산소 냉각 나선형 열교환기가 액체 질소와 열교환하는 실험 장치를 구성하고 열교환기의 열전달량을 계측하여, 외부 총 열전달 계수를 도출하였다. 측정된 외부 총 열전달 계수가 모델링으로 예측 곡선과 일치함을 확인하였다.

• Journal of Biosystems Engineering
• /
• 제25권5호
• /
• pp.385-390
• /
• 2000

The heat pump is one of heating and cooling systems driven by electricity using natural energy as a heat source. The heat pump system was mainly adopted to a cooling system or a refrigeration system. In regions with a large amount of electricity, it is used as a heating system or a heating and cooling system of houses, buildings and agricultural facilities. During cold weather, air source heat pumps do not work well because of some technical problems, such as frosting on evaporator coil when outside air temperature is below -5$^{\circ}C$. In this research, the heat regenerative technology was employed to eliminate the frosting on evaporator coil and improve the COP of the heat pump system. This fiber belt heat regeneration system(FBHRS) has very simple structure consisting of a geared motor and a porous fiber belt passing through alternatively between cold and warm air duct. The laboratory test showed that the heat pump system with a FBHRS yielded an impressive COP higher than 3.5 at the outside air temperature of -7$^{\circ}C$ in heating mode.

• 전력전자학회논문지
• /
• 제23권1호
• /
• pp.24-31
• /
• 2018

An induction heating (IH) resonant converter, as well as its coil design method, is proposed in this study to improve the heat capability of low- and high-resistance IH vessels. Conventional IH resonant converters have been designed only for heating high-resistance containers designed for IH application. Thus, the primary current in the resonant tank becomes extremely high to transfer the rated power when the converter heats the low-resistance vessel. As a result, the rated power cannot be transferred due to overcurrent flows against the rated switch current. Hence, the optimal number of coil turns and proper operating frequency to heat high- and low-resistance vessels are proposed in this study by analyzing an IH load model. Simulation and experimental results using a 2.4 kW prototype resonant converter and its IH coil validate the proposed design.

• 대한조선학회논문집
• /
• 제45권3호
• /
• pp.303-308
• /
• 2008

The induction heating is more efficient for a plate bending because of its easy operation and control of working parameters, compared with the heating by a gas torch. The existing axis symmetric analysis method could neither handle initial curved plates nor be used in the optimization of coil shapes because of its limit of an axis symmetric coil shape. But the proposed method using some discrete part models and analysis processes could overcome these difficulties and show more accurate results in temperatures and deflections of flat or curved plates with initial curvature than those in the existing axis symmetric analysis method. This method is composed of the multi-disciplinary analyses such as an electro magnetic analysis, a heat transfer analysis and a deformation analysis based on inherent strain approach per each step. Traditionally, the coil shape in the induction heating is circular shape and it needs the moving process along heating lines. To overcome this, the 'Long Type Coil' with some linear parallel coils was proposed. It did not need the moving process along heating lines and reduced the heating process time. The results of experiments were compared with those of the simulation.

• 한국산학기술학회논문지
• /
• 제15권5호
• /
• pp.2623-2627
• /
• 2014

본 연구의 목적은 우퍼 스피커 유닛의 열전달 특성 고찰하기 위하여 입력신호를 500Hz, 1000Hz, 2000Hz 그리고 3000Hz로 변화시키면서 실험을 수행하였다. 이를 위하여, 우퍼 스피커 유닛의 더스트 캡을 제거하고 보빈 내부에 열전대를 부착하여 보이스 코일에서 발생되는 온도를 측정하였고 주변으로의 열전달 특성을 파악하였다. 결과적으로, 입력신호가 감소할수록 보이스 코일 온도가 증가하였고, 입력신호가 증가할수록 스피커 유닛 각 부품의 온도편차가 증가하는 것을 확인하였다. 또한 1800sec및 입력신호 500Hz에서 보이스 코일 온도는 3000Hz에 비하여 48.4% 감소하였다.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2013년도 제46회 KOSCO SYMPOSIUM 초록집
• /
• pp.65-68
• /
• 2013

In a syngas cooling system of coal gasification process, fly slag carried by syngas deposit on the surface of heat exchanger. The deposited materials form a fouling layer with several millimeters thickness, disturbing heat transfer between steam and syngas. This study investigates flow and heat transfer characteristics of syngas in helical coil heat exchanger using computational fluid dynamics under clean and fouled surface condition. Process model were also designed and its results are in good agreement with CFD results.