• International Journal of Advanced Culture Technology
• /
• 제3권2호
• /
• pp.34-41
• /
• 2015

Bonding strength of a thermal sprayed coating is difficult to measure using a conventional pull-off test method. Scratch test is a potential alternative testing method. An adhesive and a cohesive bond strength of the coating can be measured by the pull-off test while the scratch test performed on the cross-section of the thermal sprayed coating can only demonstrate the cohesive bond strength of the coating. Nevertheless, it is still beneficial to perform the scratch testing on the cross-section of the coating for the sake of comparison thus providing an alternative to the pull-off test. The scratch test method can reduce testing time and cost in the long run due to a significant cost reduction in consumables and energy and time saving from the curing step of the glue used in the pull-off test. This research investigates the possibility of using the scratch test to measure the cohesive bond strength of Mo/NiCrBSi composite coating. The results from the pull-off test and the scratch test indicate that the cohesive bond strengths of the Mo composite coating show similar trend and that the cohesive bond strength are increased when increasing NiCrBSi content.

• Advances in aircraft and spacecraft science
• /
• 제1권2호
• /
• pp.177-196
• /
• 2014

A theoretical exploration for determining the characteristic length of the cohesive zone for a double cantilever beam (DCB) specimen under mode I loading was conducted. Two traction-separation laws were studied: (i) a law with only a linear elastic stage from zero to full traction strength; and (ii) a bilinear traction law illustrating a progressive softening stage. Two analytical solutions were derived for the first law, which fit well into two existing solution groups. A transcendental equation was derived for the bilinear traction law, and a graphical method was presented to identify the resultant cohesive zone length. The study using the bilinear traction law enabled the theoretical investigation of the individual effects of cohesive law parameters (i.e., strength, stiffness, and fracture energy) on the cohesive zone length. Correlations between the theoretical and finite element (FE) results were assessed. Effects of traction law parameters on the cohesive zone length were discussed.

• 한국지반공학회논문집
• /
• 제29권11호
• /
• pp.73-84
• /
• 2013

사면 내 토사가 붕괴되거나 토석류가 발생하는 경우 파괴면에 작용하는 전단강도는 0에 가깝게 되면서 토사가 비점성 액체와 같이 유동한다. 점성토는 함수비 증가에 따라 그 연경도가 달라지며 액체상태로 바뀌는 액성한계에서 도 약간의 전단강도를 가진다. 본 연구에서는 점성토의 전단강도가 0이 되어 흐름을 유발하는 함수비를 찾고자 하였 다. 카올리나이트, 벤토나이트, 그리고 카올리나이트(50%)+벤토나이트(50%)와 같은 세 종류의 점토에 혼합수로 증류 수, 해수, 또는 미생물용액을 혼합하여 액성한계 상태로 만든 다음 함수비를 단계적으로 증가시키면서 토베인 시험기 를 이용하여 비배수전단강도를 측정하였다. 액성한계와 소성한계에서 비배수전단강도의 범위는 각각 3.6-9.2kPa와 24-45kPa 정도이었다. 한편 측정 결과로부터 비배수전단강도가 급격하게 변화하는 값에 해당하는 함수비를 흐름함수 비(Flow Water content)로 정의하였으며, 비배수전단강도가 0이 될 때의 함수비를 흐름한계(Flow Limit)로 정의하였다. 그리고 흐름한계와 액성한계의 상관관계를 살펴보기 위하여 흐름한계와 액성한계의 차이를 점성지수(Cohesive Index) 로 정의하였다. 또한 흐름한계와 소성한계의 차이를 새로운 소성지수(New Plasticity Index)로 정의하였으며, 흐름한계를 이용하여 새로운 액성지수(New Liquidity Index)도 정의하였다. 흐름한계(Flow Limit)는 액성한계보다 1.5-2배 정도 높은 값을 보였으며, 새로운 소성지수는 기존 소성지수보다 2-5.5배 정도 높았다.

• 소성∙가공
• /
• 제18권5호
• /
• pp.385-391
• /
• 2009

An adhesively bonded power steering cylinder with a steel tube and an aluminum bracket was developed to reduce the weight of steering systems. To achieve the joint strength between the steel tube and of the aluminum bracket, the shape aluminum bracket re-designed by using the FE-analysis. Fracture behavior of the adhesive layer was considered by a cohesive zone model(CZM), which is based on the two-parameter fracture phenomenon with critical stress and fracture toughness. From the result of FE-analysis with CZM, re-designed power steering cylinder satisfied the desired joint strength for axial and torsion modes. And its joint strength was verified by the fracture test in each mode.

• Restorative Dentistry and Endodontics
• /
• 제19권2호
• /
• pp.633-640
• /
• 1994

The tensile bond strength to dentin was measured for three glass-ionomer cement and composite resin combinations: two light-curing glass-ionomer cements(Vitrebond and XR - Ionomer) and one traditional glass - ionomer cement(Ketac - Bond), two adhesive systems(Scotchbond, and XR - Bonding System), and a corresponding composite resin. The bond strength of this "sandwich" was also compared with that of the same cements used in bulk. Vitredbond showed a significantly higher bond strength in bulk than did the other two cements. Of the sandwiches, the XR - Iomomer and XR - Bond combination showed a bond strength significantly higher than that of the Vitrebond and Scotchbond or Ketac- bond and Scotchbond combination. The fracture of the bond was mainly adhesive for Vitrebond, cohesive for XR - Ionomer when used in bulk and adhesive - cohesive when used in a sandwich, and cohesive for Ketac-Bond.

• Computers and Concrete
• /
• 제20권3호
• /
• pp.291-295
• /
• 2017

Tests on the fracture behavior of CFRP-concrete composite bonded interfaces have been extensively carried out. In this study, a progressive damage model is employed to simulate the fracture behaviors. The crack nucleation, propagation and more other details can be captured by these models. The numerical results indicate the fracture patterns seem to depend on the relative magnitudes of the interface cohesive strength and concrete tensile strength. The fracture pattern transits from the predominated adhesive-concrete interface debonding to the dominated concrete cohesive cracking as the interface cohesive strength changes from lower than concrete tensile strength to higher than that. The numerical results have an agreement with the experimental results.

• Geomechanics and Engineering
• /
• 제4권2호
• /
• pp.135-150
• /
• 2012

This paper presents the study of the effect of microorganism Bacillus pasteurii on the properties such as Atterbergs' limit and unconfined compressive strength of cohesive soils. The results of this study reveal that the liquid limit and plasticity index for all clay soils decreased and the unconfined compressive strength increased. Decrease in plasticity index is very high for Kuttanad clay followed by bentonite and laterite. The unconfined compressive strength increased for all the soils. The increase was high for Kuttanad soil and low for laterite soil. After 24 h of treatment the improvement in the soil properties is comparatively less. Besides the specific bacteria selected Bacillus pasteurii, other microorganisms may also be taking part in calcite precipitation thereby causing soil cementation. But the naturally present microorganisms alone cannot work on the calcite precipitation.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 추계학술대회 논문집
• /
• pp.224-228
• /
• 2002

To study the trafficability on soft and cohesive benthic terrain, a soil bin is designed and constructed. The information of shear strength of pacific seafloor and the results of dimensional analysis of vehicle-train system are used as basic datum for concept design of soil bin. Cohesive benthic terrain is modeled by means of bentonite-water mixture. The shear strength of the mixture is measured by motorized shear meter. Several facilities are constructed for mixing and evening modeled soil, transporting vehicle model. The shear strength in soil bin is investigated for depth, age and velocity. The result of this study is used as basic information to the experiment, study for development of crawler on benthic terrain.

• 한국전산구조공학회논문집
• /
• 제31권3호
• /
• pp.121-125
• /
• 2018

본 연구에서는 굴곡 계면을 따른 균열 진전을 응집 요소를 사용하여 유한요소 해석을 수행하였고 균열 선단에서 복합 모드 하중을 고려하기 위하여 BK 법칙을 적용하였다. 정현파 굴곡 계면을 갖는 이중 외팔보에 하중을 부여하고 복합 모드 응집 법칙에서 응집 강도와 응집 에너지에 따른 하중-변위 선도의 변화를 알아보았다. 응집 강도가 커지면 응집 영역 크기가 상대적으로 작아지고 균열 진전에 따른 하중-변위 선도에 굴곡이 나타나는 것을 보여 주었으며 인장과 전단 응집에너지 비율에 따라 하중의 증가와 하중-변위 선도에 굴곡이 나타나는 것을 보여주었다. 또한 굴곡 계면의 형상에 따른 균열 진전 거동의 영향을 분석하였는데 균열의 형상비가 커지면 균열 진전을 위한 더 큰 균열 분리 에너지가 요구되는 것을 보여 주었다. 굴곡 계면의 형상과 응집 법칙을 변화시켜 파괴 인성을 크게 향상시킬 수 있으며 균열 진전 거동을 변화시킬 수 있게 된다.

• 한국지반공학회논문집
• /
• 제30권7호
• /
• pp.41-53
• /
• 2014

본 연구는 절리형성 암반지층 굴착벽체 작용토압의 크기 및 분포에 대해서 절리의 점착강도, 암석종류 및 절리경사각을 달리하여 조사하였다. 본 연구는 특히 절리 점착강도의 영향에 대해 초점을 두었다. 실내모형실험(Son and Park, 2014)에 근거하여 암석과 구조물의 상호작용을 고려하면서 확장된 매개변수 연구를 수행하였다. 이 때 매개변수 연구는 암석과 절리의 거동특성을 고려할 수 있도록 개별요소법에 근거하여 수행하였다. 연구결과 굴착벽체에 작용하는 토압은 암석 및 절리경사각 뿐만아니라 절리 점착강도에 의해서 크게 영향을 받는 것으로 나타났다. 절리 점착강도의 영향은 특히 절리가 활동될 수 있는 조건에서 크게 나타났다. 본 연구에서는 서로 다른 조건에서 절리의 활동을 방지하기 위한 절리 점착강도의 크기를 조사하였다. 연구결과는 또한 토사지반에서의 토압산정을 위해 자주 이용되는 Peck의 경험토압과도 비교되었다. 비교결과 절리형성 암반지층에서 발생하는 토압은 토사지반에서의 토압과는 크게 다를 수 있다는 것을 나타냈다. 본 연구결과는 향후 절리형성 암반지층 굴착벽체 작용토압에 대해 보다 나은 이해를 제공할 수 있을 것으로 기대된다.