• 한국전산유체공학회지
• /
• 제16권3호
• /
• pp.8-14
• /
• 2011

Although the geometry of circular cylinder is simple, the flow is complicate because of the flow separation and vortex shedding. In spite of many numerical and experimental researches, the flow around a circular cylinder has not been clarified even now. It has been known that the unsteady vortex shedding from a circular cylinder can vibrate and damage a structure. Lock-on phenomenon is very important in the flow around an oscillating circular cylinder. The lock-on phenomenon is that when the oscillation frequency of the circular cylinder is at or near the frequency of vortex shedding from a stationary cylinder, the vortex shedding synchronizes with the cylinder motion. This phenomenon can be recognized by the spectral analysis of the lift coefficient history. At the lock-on region the vortex is shedding by the modulated frequency to the body frequency. However, the vortex is shedding by the mixed frequencies of natural shedding and forced body frequency in the region of non-lock-on. In this paper, it was analyzed the relation between the frequency of rotary oscillating circular cylinder and the vortex shedding frequency.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2012년도 제38회 춘계학술대회논문집
• /
• pp.356-363
• /
• 2012

This paper addresses an analytical study on the gas-solid two phase flows in a nozzle. The primary purpose is to get recognition into the gas-solid suspension flows and to investigate the particle motion and its influence on the gas flow field. The present study is the primal step to comprehend the gas-solid suspension flow in the convergent-divergent nozzle. This paper try to made a development of an analytical model to study the back pressure ratio, particles loading and the particle diameter effect on gas-solid suspension flow. Mathematical model of gas-solid two phase flow was developed based on the single phase flow models to solve the quasi-one-dimensional mass, momentum equations to calculate the steady pressure field. The influence of particles loading and particle diameter is analyzed. The results obtained show that the suspension flow of smaller diameter particles has almost same trend as that of single phase flow using ideal gas as working fluid. And the presence of particles will weaken the strength of the shock wave; the bigger particle will have larger slip velocity with gas flow. The thrust coefficient is found to be higher for larger particles/gas loading or back pressure ratio, but it also depends on the ambient pressure.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권1호
• /
• pp.59-69
• /
• 2019

This paper focuses on the numerical simulation of ice abrasion induced by unbreakable ice floe. Under the assumption that unbreakable floes behave as rigid body, the Discrete Element Method (DEM) was applied to simulate the interaction between a fixed structure and ice floes. DEM is a numerical technique which is eligible for computing the motion and effect of a large number of particles. In DEM simulation, individual ice floe was treated as single rigid element which interacts with each other following the given interaction rules. Interactions between the ice floes and structure were defined by soft contact and viscous Coulomb friction laws. To derive the details of the interactions in terms of interaction parameters, the Finite Element Method (FEM) was employed. An abrasion process between a structure and an ice floe was simulated by FEM, and the parameters in DEM such as contact stiffness, contact damping coefficient, etc. were calibrated based on the FEM result. Resultantly, contact length and contact path length, which are the most important factors in ice abrasion prediction, were calculated from both DEM and FEM and compared with each other. The results showed good correspondence between the two results, providing superior numerical efficiency of DEM.

• Structural Engineering and Mechanics
• /
• 제70권3호
• /
• pp.325-337
• /
• 2019

In the present article, cross ply laminated composite plates are considered and a simple sinusoidal shear deformation model is tested for analyzing their flexural, stability and dynamic behaviors. The model contains only four unknown variables that are five in the first order shear deformation theory (FSDT) or other higher order models. The in-plane kinematic utilizes undetermined integral terms to quantitatively express the shear deformation influence. In the proposed theory, the conditions of zero shear stress are respected at bottom and top faces of plates without considering the shear correction coefficient. Equations of motion according to the proposed formulation are deduced by employing the virtual work principle in its dynamic version. The analytical solution is determined via double trigonometric series proposed by Navier. The stresses, displacements, natural frequencies and critical buckling forces computed using present method are compared with other published data where a good agreement between results is demonstrated.

• Steel and Composite Structures
• /
• 제52권6호
• /
• pp.609-620
• /
• 2024

The impact problem of imperfect beams is crucial in engineering fields such as water conservancy and transportation. In this paper, the low velocity impact of graphene reinforced metal foam beams with geometric defects is studied for the first time. Firstly, an improved Hertz contact theory is adopted to construct an accurate model of the contact force during the impact process, while establishing the initial conditions of the system. Subsequently, the classical theory was used to model the defective beam, and the motion equation was derived using Hamilton's principle. Then, the Galerkin method is applied to discretize the equation, and the Runge Kutta method is used for numerical analysis to obtain the dynamic response curve. Finally, convergence validation and comparison with existing literature are conducted. In addition, a detailed analysis was conducted on the sensitivity of various parameters, including graphene sheet (GPL) distribution pattern and mass fraction, porosity distribution type and coefficient, geometric dimensions of the beam, damping, prestress, and initial geometric defects of the beam. The results revealed a strong inhibitory effect of initial geometric defects on the impact response of beams.

• 한국군사과학기술학회지
• /
• 제18권2호
• /
• pp.181-188
• /
• 2015

This paper present, the result of the guidance and control law for a course correction munitions(CCM) with 2sets of canards positioned in the rotating nose section. The nonlinear simulation model of the CCM was developed based on 7DOF equation of motion. The ability of correcting position was verified by open-loop control input with nonlinear model. The guidance and control command was constructed by reference trajectory which can be obtained with no control. Finally, the performance of the guidance and control law was evaluated through Monte-carlo simulation. The CEP(Circular Error Probability) was obtained by considering the errors in muzzle velocity, aerodynamic coefficient, wind, elevation and azimuth angle and density.

• Steel and Composite Structures
• /
• 제24권5호
• /
• pp.603-613
• /
• 2017

In this research, the free vibration response of laminated composite plates is investigated using a novel and simple higher order shear deformation plate theory. The model considers a non-linear distribution of the transverse shear strains, and verifies the zero traction boundary conditions on the surfaces of the plate without introducing shear correction coefficient. The developed kinematic uses undetermined integral terms with only four unknowns. Equations of motion are obtained from the Hamilton's principle and the Navier method is used to determine the closed-form solutions of antisymmetric cross-ply and angle-ply laminates. Numerical examples studied using the present formulation is compared with three-dimensional elasticity solutions and those calculated using the first-order and the other higher-order theories. It can be concluded that the present model is not only accurate but also efficient and simple in studying the free vibration response of laminated composite plates.

• 대한기계학회논문집B
• /
• 제25권12호
• /
• pp.1869-1878
• /
• 2001

Experiments are carried out to investigate the effect of pulsations on the flow and heat transfer characteristics of an axisymmetric impinging jet on a flat plate heated by using a gold coated aim. Vertex motion in the impinging jet is visualized using a fog generator, and a thermochromatic liquid crystal (TLC) technique is used to measure the time averaged local temperature distributions on the impingement plate. In addition, the quantitative data for mean velocity and turbulence intensity are obtained employing hot-wire anemometer. Parameters such as pulsating frequency (f = 0, 10 and 20 Hz) and the nozzle-to-palate spacing (H/D = 2, 10) are considered at the jet Reynolds number of 20,000. Consequently, the significant changes of flow structure and local Nusselt number distribution due to pulsations are observed. In the case of H/D = 2, the enhanced heat transfer coefficient exceeding 30 % is observed at the stagnation point. At the high H/D, heat transfer rate increases with pulsation frequency.

• 대한조선학회지
• /
• 제23권2호
• /
• pp.1-13
• /
• 1986

The nonlinear hydrodynamic forces acting on a two-dimensional circular cylinder, oscillating with large amplitude in the free surface, are calculated by using the Semi-Lagrangian Time-Step-ping Method used by O.M. Faltinsen. In present calculation the position and the potential value of free surface are calculated using the exact kinematic and dynamic free surface boundary condition. At each time step an integral equation is solved to obtain the value of potential and normal velocity along the boundaries, consisting of both the body surface and the free surface. Some effort was devoted to the elimination of instability arising in the range of high frequency. Numerical simulations were performed up to the 3rd or 4th period which seems to be enough for the transient effect to die out. Each harmonic component and time-mean force are obtained by the Fourier transform of forces in time domain. The results are compared with others' experimental and theoretical results. Particularly, the calculation shows the tendency that the acceleration-phase 1st-harmonic component(added mass) increases as the motion amplitude increases and a reverse tendency in the velocity-phase 1st-harmonic component(damping coefficient). The Yamashita's experimental result also shows the same tendency. In general, the present result show relatively good agreement with the Yamashita's experimental result except for the time-mean force.

• 한국시뮬레이션학회논문지
• /
• 제28권3호
• /
• pp.83-89
• /
• 2019

본 연구는 회전 비행체(Magnus rotor)를 탑재한 분산탄두의 분산 균일도에 미치는 요인 분석과 성능지표를 도출하기 위해 모탄의 속도 V와 회전속도 ${\omega}$, 비행경로각(flight path angle) ${\gamma}$ 그리고 고도 h의 변화에 따른 해석 결과를 기술했으며, 이때 모탄의 회전속도와 속도의 비를 새로운 변수로 정의했다. 자탄의 분산 해석에는 풍동실험을 통해 획득한 공력계수를 사용한 6 자유도 운동방정식을 이용했으며, 분산도 분석을 위해 회귀분석과 결정계수를 구해 분산도를 평가했다. 해석결과 최적의 회전속도와 낙하속도의 비, 비행경로각(flight path angle)을 구할 수 있었으며, 방출고도는 분산도에 회전속도와 낙하속도의 비, 비행경로각(flight path angle)의 영향에 비해 영향은 크지 않고, 자탄의 분산반경에 영향이 큰 것을 확인했다.