• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.308-312
• /
• 1999

Developed the model equations which calculate roll force, roll power during hot rolling in real time. The variables which mainly effect on the roll force, roll power are shape factor, reduction, roll diameter, roll velocity, strip inlet temperature, carbon content of strip and strip-roll contact friction coefficient. Among these variables roll diameter, roll velocity, inlet temperature, carbon content and friction coefficient can be excluded in interpolated model equation by introducing equation of die force(F'), power(p') of the frictionless uniform plane strain compression which can be calculated without iteration. At the case of coulomb friction coefficient of 0.3, we evaluated coefficient of polynomial equations of {{{{ { F} over {F' } }}}}, {{{{ { Pf} over {Pd }, { Pd} over {P' } }}}} from the result of finite element analysis using interpolation. It was found that the change of values of {{{{ { F} over {F' }, { P} over {P' } }}}} with the friction coefficient tend to straight line which slope depend only on shape factor. With these properties, developed model equations could be extended to other values of coulomb friction coefficient. To verify developed roll force, roll power model equation we compared the results from these model equation with the results from these model equation with the results from finite element analysis in factory process condition.

• Transactions of Materials Processing
• /
• v.18 no.6
• /
• pp.465-470
• /
• 2009

The frictional behaviors of Cermets/Cr-Ceramics and Cu-Al coatings of piston ring were investigated. Friction tests were carried out by pin-on-disk test and materials properties of coating layer were analyzed by nano indentation tester. The effect of surface roughness of cylinder liner on the friction coefficient was analyzed. This study provided tribological data of hard and soft piston ring coatings against cylinder liner. The surface roughness does exert an influence on the average friction coefficient, with smoother surfaces generally yielding lower friction coefficients. In case of hard-coating, the scratch depth, width and pile-up height had close relationship with hardness. So the scratch width, depth and pile-up height increases with decreasing friction coefficient. But in case of soft-coating, the friction coefficients are strongly dependent on the morphological characteristics such as, scratch depth, width, pile-up height and elastic modulus.

• Tribology and Lubricants
• /
• v.16 no.4
• /
• pp.266-273
• /
• 2000

The friction characteristics of phenolic resin and model friction materials were investigated with the content of hexamethylenetetamine (HEXA). At 10 wt.% of HEXA, the phenolic resin and model friction materials showed the most stable friction coeffcient in constant temperature test at various test conditions because of its good thermal stability and proper curing reaction. It was found from constant interval test in mild condition that the friction coeffcients of friction materials cured with 10 wt.% of HEXA was the highest and stable values in the whole range of braking operations. However, at the severe condition in constant interval test, the friction coefficient of friction materials cured with 10 wt.% to of HEXA was lowered and as the number of braking operation increased, the values became stable. In order to obtain the thormal stable friction materials, the content of HEXA from 5 to 10 wt.% could be recommended.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.6
• /
• pp.207-213
• /
• 1999

In this study, the possibility of estimation of friction coefficient between tire and road surface using running car data are checked. To get necessary data, such as tire and car velocities and braking force, a test car is driven with certain magnitude of decelerations from pre-set initial velocities to stop . The data are used to estimate friction coefficient with property chosen parameters , e.g,, driving stiffness, pressure distribution functions, etc. Experimental results show that running data car be used with properly chosen parameters to estimate friction coefficient.

• Journal of the Korean Society of Industry Convergence
• /
• v.8 no.3
• /
• pp.135-141
• /
• 2005

The static friction coefficients of 4 samples against each different temperatures were similar values. Compared against RT, at $80^{\circ}C$ the static friction coefficients decreased from 0.130 to 0.116 that was equal from 88% to 90% of the static friction coefficients respectively. Otherwise the dynamic friction coefficients compared against RT, decreased from 0.138 to 0.088 which was from 71% to 77.5% respectively at $80^{\circ}C$. The noise characteristics were judged by s/d value. And when the s/d value was limited less than 0.8, noise concerns were released. At 3000 engaging cycles the static friction and the dynamic friction coefficient were 0.137 and 0.073 respectively. When plate pressure rose up to $195kg_f/cm^2$, the static friction coefficient decreased from 0.137 to 0.125 but this decreasing could be considered as stable. When speed rose up to 2200rpm, the static friction coefficient decrease from 0.14 to 0.13 but this decreasing could be considered as stable. At 3000 engaging cycles the amount of worn out was 0.04 : the thickness of disc was decrease from 4.72mm to 4.68mm. But regarding the normal operation condition, further more worn-out could not be expected. Therefore concerning worn-out, the basic oil could be considered as appropriate.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.4
• /
• pp.527-534
• /
• 2023

This paper conducted a study on the application of ceramic materials for bridge bearing that can complement the durability of PTFE, a conventional bridge bearing friction material, and exhibit low coefficient of friction and friction behavior without lubricant. The ceramic material was zirconia (ZrO₂), and the friction behavior was evaluated according to the roughness coefficient. The roughness coefficient was divided into 0.8 and 0.027, and the average coefficient of friction was calculated to be 0.16 under 15 MPa surface pressure. Afterward, ceramic was made into friction material and applied to the bridge bearing, and performance comparison with PTFE bridge bearing was conducted through compression test and friction test. In the compression test, the ceramic and PTFE bridge bearing showed ideal compression behavior depending on the load. No fractures or defects were observed in the ceramic bridg bearing, but lubricant loss was observed in the PTFE bridge bearing. The average coefficient of friction of the ceramic bridge bearing analyzed through friction behavior was 0.16. The inherent material properties of the physical and chemical properties of ceramics, the excellent mechanical properties derived from the performance evaluation, and the coefficient of friction of 0.16 suggest that it can be considered as a friction material.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.05a
• /
• pp.201-203
• /
• 2012

The establishment of the technology for evaluating friction resistance and pipe pressure and the relation of the fluid characteristics and pumpability of concrete is essential for the evaluation of concrete pumping performance for high speed construction of super-tall building. So, this study focuses on quantitative evaluation of concrete fluid characteristics and surface friction resistance under the change of concrete mix proportion and pumping condition. In this study, we measured the rheology of concrete and pipe pressure and surface friction characteristics when pumping. And, relations between the rheology characteristics of concrete and pumping performance was investigated by experiment. As the result of the experiment, high regression between the surface friction and pressure gradient was confirmed. And, prediction model to evaluate the friction resistance coefficient and pipe pressure reduction coefficient was suggested.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2002.10b
• /
• pp.385-386
• /
• 2002

The friction characteristics of contact region between vane tip and cam-ring is studied with an experimental device model. The radius of vane tip is less than 1 mm and sliding speed is lower than 10 m/s. The friction characteristics of the actual oil hydraulic vane pump is estimated on the basis of coefficient of friction. The coefficient of friction can be obtained by measuring the frictional forces in the contact region. The lubrication condition between vane and disk is modeled after the actual condition between the vane and cam-ring.

• Journal of Mechanical Science and Technology
• /
• v.20 no.4
• /
• pp.513-521
• /
• 2006

The performances of porous bearings under different operating conditions were experimentally investigated in this study. Material groups studied are 90%Cu + 10%Sn bronze and 1%C + % balance Fe iron-based self-lubricating P/M bearings at constant (85%) density. In the experiments, the variation of the coefficient of friction and wear ratio of those two different group materials for different sliding speeds, loads, and temperatures were investigated. As a result, the variation of the friction coefficient-temperature for both constant load, and constant sliding speed, friction coefficient-average bearing pressure, PV-wear loss and temperature-wear loss curves were plotted and compared with each other for two materials, separately. The test results showed that Cu-based bearings have better friction and wear properties than Fe-based bearings.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2000.11a
• /
• pp.29-36
• /
• 2000

This investigation has been studied about friction and wear properties which were important problem, when carbon fiber reinforced plastic(CFRP) was used practically. Unidirection carbon fiber reinforced composites was fabricated with epoxy resin matrix and carbon fiber as a reinforced, and its surface was modified by the ion-assisted reaction. And then we tested the their friction and wear properties according to the ion-irradiation. when the amount of ion-irradiation was 1${\times}$10l6$\^$16/ ions/$\textrm{cm}^2$, the friction coefficient values were about 0.1, where as, the friction coefficient values of non-treatment composites were about 0.16. The former was the stablest in wear mode. We know that ion-irradiation was not proportioned to the friction coefficient, so we found the optimal conditions of the friction and wear according to the ion-irradiation.