• Korean Chemical Engineering Research
• /
• v.49 no.3
• /
• pp.277-284
• /
• 2011

In this study, UV-curing type organic - inorganic hybrid hard coating solutions were prepared from alumina sols and acrylate monomers. The mixture of alumina sols, prepared from aluminum isopropoxide, and a silane coupling agent, methacryloxypropyl trimethoxysilane(MPTMS), was used as an inorganic component. Also, the mixture of acrylate monomers, pentaerythritol triacrylate(PETA), 1,6-hexanediol diacrylate(HDDA) and dipentaerythritol hexaacrylate (DPEHA), was used as an organic component. The organic-inorganic hybrid coating solutions were obtained by mixing the inorganic component and organic component, deposited on polycarbonate substrates by spin coating and densified by UV-curing. The effect of the amount of MPTMS in the inorganic component and the irradiation time during UV-curing was studied on the properties of coating films. As a result, when 0.20 mole of MPTMS was used, the pencil hardness of coated films showed an excellent pencil hardness of 3H and also exhibited a good abrasion resistance of 2% in haze.

• Polymer(Korea)
• /
• v.27 no.6
• /
• pp.555-561
• /
• 2003

The self-assembled monolayer coating of octadecyltrichlorosilane (OTS) on the silicon based MEMS was investigated and surface characteristics were considered as a function of coating conditions and reagent composition. The sulfuric peroxide mixture (SPM) solution was used to form -OH group which caused the hydrophilic characteristic on silicon surftce. Highest hydrophilicity was obtained by SPM solution with 85% acid content at room temperature. OTS was applied on the silicon surface by means of self-assembled monolayers (SAMs) coating. It was found that sol-gel reaction was took place between -OH group on the silicon surface and -Cl group in OTS. As a result, the contact angle increased due to the increase of hydrophobicity by Si-O bonding of SAMs. Sol-gel reaction could be controlled by coating conditions as well as reagent composition in OTS coating solution.

• Applied Science and Convergence Technology
• /
• v.24 no.6
• /
• pp.219-223
• /
• 2015

Enhancement of the surface hydrophobicity of polydimethylsiloxane (PDMS) thin films deposited on substrates covered with titanium dioxide ($TiO_2$) nanospheres was studied. First, a low-temperature solution-phase method using polyvinylpyrrolidone (PVP) as a surface capping agent and a water/dimethylformamide (DMF) mixture as the reaction medium was used to synthesize monodisperse $TiO_2$ nanospheres. It was possible to easily control hydrolysis rate of the Ti-precursors and the size of the synthesized nanospheres by varying the amount of PVP and the volume ratio of the solvent mixture. Spray coating of the synthesized $TiO_2$ nanospheres under the PDMS film increased the water contact angle of the film surface to $150.3^{\circ}$. This simple treatment can modify the surface morphology at a nanometer scale without any long or complicated nanoprocess; hence, the surface enters the superhydrophobic Cassie-Baxter regime.

• Korean Journal of Metals and Materials
• /
• v.46 no.3
• /
• pp.182-188
• /
• 2008

Carbon nanotubes(CNTs) have outstanding mechanical, thermal, and electrical properties. Thus, by placing nanotubes into appropriate matrix, it is postulated that the resulting composites will have enhanced properties. Cold spray can produce thick metal-based composite coatings with very high density, low oxygen content, and phase purity, which leads to excellent physical properties. In this study, we applied cold spray coating process for the consolidation of Cu/CNT composite powder. The precursor powder mixture, in which CNTs were filled into copper particles, was prepared to improve the distribution of the CNT in copper matrix. Pure copper coating was also conducted by cold spraying as a reference. Annealing heat treatment was applied to the coating to examine its effect on the properties of the composite coating. The hardness of Cu/CNT composite coating represented similar value to that of pure copper coating. It was importantly found that the electrical conductivity of the Cu/CNT composite coating significantly increased from 53% for the standard condition to almost 55% in the optimized condition, taking annealed ($500^{\circ}C/1hr$.) copper coating as a reference (100%). The thermal conductivity of Cu/CNT composite coating layer was higher than that of pure Cu coating. It was also found that the electrical and thermal conductivities of Cu/CNT composite could be improved through annealing heat treatment. The microstructural evolution of Cu/CNT coating was also investigated and related to the macroscopic properties.

• Journal of the Korea Furniture Society
• /
• v.11 no.1
• /
• pp.37-44
• /
• 2000

This work was done to investigate problems of cashew coating in a wooden-art industry such as ritual vessels and to improve a curing property of cashew film. The main problem in the cashew coating industry was a small-scale business, insufficiency of facilities, lack of knowledge about cashew resin and painting, and lack of a technology of productivity improvement by accelerated drying time of cashew film. In present, cashew coating for ritual vessels mostly used the petroleum as a thinner. The time of set to touch of cashew film thinning with petroleum on glass plates was increased with the increasement of the thinning proportion, but retarded from 3 to 11 times compared to that of an exclusive thinner according to thinning level. The addition of 20% aceton to petroleum contributed to the high reduction rate up to about 60% at the thinning level of 100%, which was effective to accelerate the drying time of cashew film. Even though only the petroleum or the petroleum-aceton(20%) mixture was used as a thinner, it did not exhibit any distinguishable differences in crack and appearance of cashew-film coated on Frexinus rhynchophylla after 5 cycles of soak under the vacuum-drying treatment.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.7
• /
• pp.550-554
• /
• 2013

Carbon nanotubes (CNT) / polyvinylidene fluoride (PVDF) piezoelectric composite films for nanogenerator devices were fabricated by spray coating method. When the CNT/PVDF mixture solution passes through the spray nozzle with small diameter by the compressed nitrogen gas, electric charges are generated in the liquid by a triboelectric effect. Then randomly distributed ${\beta}$ phase PVDF film could be re-oriented by the electric field resulting from the accumulated electrical charges, and might be resulted in extremely one-directionally aligned ${\beta}$ phase PVDF film without additional electric field for poling. X-ray diffraction patterns were used to investigate crystal structure of the CNT/PVDF composite films. It was confirmed that they revealed extremely large portion of the ${\beta}$ phase PVDF crystalline in the film. Therefore we could obtain the poled CNT/PVDF piezoelectric composite films by the spray coating method without additional poling process.

• Journal of Adhesion and Interface
• /
• v.10 no.4
• /
• pp.182-190
• /
• 2009

In this work, effect of antistrip additives to reduce moisture damage of asphalt mixture were studied. Asphalt antistripping agents were prepared by condensation of formaldehyde with tetraethylene pentamine (TEPA), triethylenetetramine (TETA) and bis(hexamethylene)-triamine (BHMT), respectively. And also the metal type antistripping agent was prepatred by neutralization of stearic acid or palmitic acid with metal hydroxide. Mechanical characteristics of the asphalt mixture added antistripping agent were evaluated with Marshall stability, submerging residuals and coating rate. It was found that antistripping agent prepared in this study reduced moisture damages of asphalt mixtures. In particular, asphalt mixtures added BHMT and C/S (Calcium stearate hydroxide) antistripping agent showed highest submerging and coating rate. Because BHMT and C/S type antistripping agent was to improve bonding between asphalt and aggregate owing to increase of amine concentration and role of metal surfactant.

• Journal of Powder Materials
• /
• v.21 no.1
• /
• pp.21-27
• /
• 2014

In this study, diatomite based materials were investigated as a support filter for silica particle coating. The silica sol for coating was synthesized by a st$\ddot{o}$ber process. The diatomite support was dry-pressed at 10 MPa and sintered at $1200^{\circ}C$ for 1 hour. The coating sol was prepared as a mixture of EtOH and silica sol. The diatomite support was coated by a dip-coating process. Silica coated diatomite filter was sintered at $1000{\sim}1200^{\circ}C$ for 1 hour. The largest pore size was decreased with increasing concentration ratio of coating sol. The gas and water permeability of silica coated diatomite decreased with increasing of concentration ratio of the coating sol.

• Journal of the Korean Ceramic Society
• /
• v.44 no.12
• /
• pp.733-739
• /
• 2007

NiO-YSZ anode-supported single cell was prepared by spin-coating YSZ and LSM slurries as electrolyte and cathode, respectively. Dense YSZ electrolyte film was successfully prepared on the porous NiO-YSZ anode substrate by tuning pre-sintering temperature of NiO-YSZ and co-firing temperature. The thickness of YSZ film was controlled by the solid content of slurry and coating cycles. The experimental conditions affecting on the thickness of YSZ film was discussed. Single cells with the active electrode area ${\sim}0.8\;cm^2$ were prepared by spin-coating the cathode layers of LSM-YSZ mixture and LSM consequently as well. The effects of the pre-sintering temperature and thus the microstructure of NiO-YSZ substrate on the current-voltage characteristics of co-fired cell were investigated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.496-496
• /
• 2011

A very simple and cost-effective method for fabrication of SiOx-incorporated diamond-like carbon (DLC) thin films at a preparation temperature of less than $200^{\circ}C$ was developed. Since DLC coating can be prepared not under vacuum but atmospheric conditions without any carrier gas flow, not only wafers but also powderic substrates can be used for DLC coating. Formation of DLC coating could result in appearance of superhydrophobic behaviors, which was sustained in a wide range of pH (1~14). DLC-coated surfaces selectively interacted with toluene in a toluene/water mixture. These results imply that our preparation method of the DLC coating can be useful in many application fields such as creating self-cleaning surfaces, and water and air purification filters.